Coral Industries 6X0 User Manual
6X0-GP
Double Swing Door
Technical Assistance is available Monday - Friday, 8:00 a.m. - 5:00 p.m. (Central Time)
1-877-723-7190 (Toll Free)
6X0-GP 7/06
PARTS LIST
FRAME PACKAGE
KEY DESCRIPTION PART QTY
A SILL (Use is optional) A001 1
B JAMB A083 2
C HEADER A070 1
D HEADER INSERT A716 2
E MAGNETIC STOP A954 1
F VINYL DRIP SWEEP V001 2
V VINYL DOOR SEAL
W H-SEAL SPLASH GUARD
(Pre-Installed) V678 6
(Use is optional) V002 1
TOOLS NEEDED
1/8" Drill Bit
(3/16" Masonry Bit for
Ceramic Tile)
Pencil
HARDWARE BAG
G 8A X 1 1/4" PAN HEAD SCREW H480 8
H ANCHOR H002 8
I PUSH/PULL HANDLE KIT HTG6 2
PLASTIC WASHER 8
EXTERIOR PULL HANDLE 2
INTERIOR PULL HANDLE 2
BUSHING 4
HANDLE CONNECTOR SCREW 4
M MAGNETIC CLOSURE KIT HKMADCH 2
MAGNETIC CLOSURE WITH MAGNET HMAH / HG92 2
VINYL V208 2
STRIKE PLATE HA75 2
J 8A X 5/8"
K 8A X 3/8"
Before starting installation of your new enclosure, carefully read all instructions and lay out parts to become familiar
with their identity. Installation is a manageable task for an experienced "Do-It-Yourselfer" and a helper.
Frameless patch-hinge doors, by nature of their design, are not completely watertight.
Anchors are furnished with every enclosure. However, the use of anchors is not recommended when attaching your enclosure
to a fiberglass unit or wall surrounds with board reinforced mounting areas. Mounting holes in this case should be drilled with
an 1/8" drill bit.
SELF-DRILLING PAN HEAD SCREW
SELF-DRILLING PAN HEAD SCREW
USE OF ANCHORS
H437 4
H900 10
Measuring Tape
Hacksaw
Phillips Screw Driver
Silicone Caulk
File
Drill
Level
Masking Tape
Scissors
Mounting this unit on tile requires the use of anchors. Special care must be taken not to crack the tile. Before drilling holes in
the tile, lightly chip glazed surface of tile at the desired locations. Drill holes using a 3/16" masonry drill bit. Insert anchors into
the holes making certain that ring on large end of anchor meets the surface of the tile.
CAUTION
Do not attempt to cut mirrors or glass used in this enclosure. Tempered glass and mirrors will shatter if cut.
Care should be taken when standing raw glass on its edge. Glass may shatter if corners are bumped or edge is rested on
a rough floor surface. Cardboard, wood blocks, or a similar surface is a safe resting surface for glass.
CLEANING
Cleaning and care of your enclosure is important to its lasting beauty. A nonabrasive liquid cleaner is recommended.
Never use scouring powder or pads.
SEALING
Seal unit by caulking along outside of enclosure where metal and bath meet, especially where sill meets threshold. If desired,
caulk inside of enclosure where jambs meet walls.
6X0-GP 7/06
SELF-DRILLING
H437
PAN HEAD SCREW
J
A070
HEADER
C
HEADER INSERT
A716
D
CLOSURE KIT
V
V678
VINYL
DOOR
SEAL
(Pre-Installed)
MAGNETIC
M
A954
E
MAGNETIC STOP
INTERIOR
HANDLE
HTG6
I
PUSH/PULL
HANDLE KIT
H900
SELF-DRILLING
PAN HEAD SCREW
K
EXTERIOR
HANDLE
V002
W
H-SEAL
SPLASH GUARD
(Use is optional)
A083
B
JAMB
A
A001 SILL
(Use is optional)
V001 VINYL
DRIP SWEEP
OUTSIDE OF SHOWER
F
Care should be taken when standing raw glass on its edge. Glass may shatter if corners are bumped or edge is
rested on a rough floor surface. Cardboard, wood blocks, or a similar surface is a safe resting surface for glass.
8A x 1 1/4" Pan Head
G
Screw
(H480 - Used for securing
Jambs to walls)
8A x 3/8 Self-Drilling Pan
K
Head Screw
(H900 - Used for securing
Hinge Rails to Jambs)
8A x 5/8" Self-Drilling Pan
J
Head Screw
(H437 - Used for securing
Magnetic Stop to Header,
Header to Jambs)
G
H480
PAN HEAD
SCREW
H
H002
ANCHOR
6X0-GP 7/06
Loading...