Coral Industries 650 User Manual
650
PAN HEAD
VERTICAL
VINYL
GLAZING
Z
HORIZONTAL
VINYL
GLAZING
Y
7000 Series • Door with Double In-Line Panels
H900
SCREW
A083
JAMB
N
B
A716
D
HEADER / SILL INSERT
A083
JAMB
B
O
H170
MAGNETIC
STRIP
H900
PAN HEAD
SCREW
N
M
HSAD
PULL HANDLE KIT
HA28
DRIP
RAIL
PLUG
P
A710
DRIP RAIL
ASSEMBLY
F
C
A781
HEADER
L
H480
PAN
HEAD
SCREW
(GIH / AHD)
H
H002
ANCHOR
A083
JAMB
A989
B
X
HB5195
SETTING BLOCK
E
MAGNETIC
DOOR STOP
A716
D
HEADER / SILL INSERT
OUTSIDE OF SHOWER
FRAME PACKAGE PARTS
KEY DESCRIPTION PART QTY
A SILL (WITH WEEP HOLES) A782 1
B JAMB A083 4
C HEADER A781 1
D HEADER / SILL INSERT A716 2
E MAGNETIC DOOR STOP A989 1
F MAGNETIC STRIP
G DRIP RAIL ASSEMBLY A710 1
DRIP RAIL TAPE
DRIP RAIL SWEEP
Y HORIZONTAL VINYL GLAZING VK188H
Z VERTICAL VINYL GLAZING VK188V / VK250V 8
*
*
*
H170 1
HT52 1
VS91 1
/
VK250H 8
HARDWARE PARTS
P DRIP RAIL PLUG HA28 1
L 8A X 1 1/4 PAN HEAD SCREW H480 6
N 8A X 3/8 PAN HEAD S.DRILLING SCREW H900 14
H ANCHORS H002 6
M PULL HANDLE KIT
X SETTING BLOCK HB5195 4
*
6-32 X 1 1/4 PAN HEAD SCREW H485 2
EXTERIOR PULL HANDLE HA31 1
INTERIOR PULL HANDLE HA32 1
Pre-Installed + May be Pre-Installed
+
HSAD
A782
A
SILL
TOOLS NEEDED
1/8" Drill Bit
3/16" Drill Bit
(3/16" Masonry Bit for
Ceramic Tile)
Scratch Awl
Measuring Tape
Hacksaw
Phillips Screw Driver
Caulking Compound
File
Drill
Level
Masking Tape
650 6/09
Before starting installation of your new enclosure, carefully read all instructions and lay out parts to become
familiar with their identity.
USE OF ANCHORS • Anchors are furnished with every enclosure. However, the use of anchors is not recommended when
attaching your enclosure to a fiberglass unit or wall surrounds with board reinforced mounting areas. Mounting holes in this case
should be drilled with an 1/8" drill bit.
Mounting this unit on tile requires the use of anchors. Special care must be taken not to crack the tile. Before drilling holes in
the tile, lightly chip glazed surface of tile at the desired locations. Drill holes using a 3/16" masonry drill bit. Insert anchors into
the holes making certain that ring on large end of anchor meets the surface of the tile.
CAUTION •
Do not attempt to cut mirrors or glass used in this enclosure. Tempered glass and mirror will shatter if cut. Care should
be taken when standing raw glass on its edge. Glass may shatter if corners are bumped or edge is rested on a rough floor surface.
Cardboard, wood blocks (provided with hardware), or a similar surface is a safe resting surface for glass.
CLEANING • Cleaning and care of your enclosure is important to its lasting beauty. A nonabrasive liquid cleaner is
recommended. Never use scouring powder or pads.
SEALING • Seal unit by caulking along outside of enclosure where metal and bath meet, especially where sill meets threshold.
If desired, caulk inside of enclosure where jambs meet walls.
Kwikstal doors are designed to be reversible and may be installed to hinge-left or hinge-right. The following
instructions show a hinge-right door.
1
Due to the manufacturing process, there may be rack
marks present at one end of your sill. Sill must be
trimmed to fit your individual opening. When cutting
sill, make certain to trim off end with rack marks.
Header and sill are identical except that the sill has weep
holes on inside surface. Identify sill with weep holes.
Determine placement of sill (A) on shower threshold. Normally
door is installed with sill centered on the flat surface of
threshold.
Sill (A)
Sill
A
Measure
Weep holes
face inside of
shower.
Measure opening at threshold and cut sill to that
measurement. If necessary, file sharp edges to fit rounded
corners of your unit.
2
Sill (A)
With sill in upside down position, apply a 1/4" bead of caulk
along bottom of sill.
Position sill on threshold with weep holes facing inside of
shower. Tape to threshold with masking tape to hold in place
while positioning jambs.
Clean caulk that squeezes out from under sill with a wooden
wedge, plastic scraper, or popsicle stick.
650 6/09
OUTSIDE OF SHOWER
Clean caulk that
squeezes out from
under sill.
OUTSIDE OF SHOWER
Sill
A
A
Sill
Masking
Tape
File sharp edges to
fit contour of your
unit if needed.
Silicone
Caulk
Weep holes face
inside of shower.
Threshold
Loading...