Coral Industries 4HJ User Manual
4HJ-GP
Swing Door
Technical Assistance is available Monday - Friday, 8:00 a.m. - 5:00 p.m. (Central Time)
1-877-723-7190 (Toll Free)
4HJ-GP 10/06
PARTS LIST
FRAME PACKAGE
DESCRIPTIONKEY PART QTY
A SILL A001 1
B HINGE / MAGNETIC DOOR STOP A081 2
C VINYL DOOR SEAL V678 4
D VINYL DRIP SWEEP V001 1
HARDWARE BAG
E HINGE H006 2
F PUSH/PULL HANDLE KIT HTG6 1
PLASTIC WASHER 4
EXTERIOR PULL HANDLE 1
INTERIOR PULL HANDLE 1
BUSHING 2
HANDLE CONNECTOR SCREW 2
L ANCHOR H002 8
G 8A X 1 1/4" FLAT HEAD SCREW H810 4
H 8A X 2" FLAT HEAD SCREW H462 4
I 4MM ALLEN WRENCH H636 1
J 3/32 ALLEN WRENCH H635 1
K MAGNETIC CATCH KIT HKMAGCH 1
MAGNET HOLDER WITH MAGNET HMAH / HG92 1
METAL SLIDE HA75 1
HANDLE VINYL V208 1
TOOLS
NEEDED
1/8" Drill Bit
Pencil
Measuring Tape
Hacksaw
Phillips Screw Driver
Silicone Caulk
File
Drill
Level
Masking Tape
Before starting installation of your new enclosure, carefully read all instructions and lay out parts to become familiar
with their identity. Installation is a manageable task for an experienced "Do-It-Yourselfer" and a helper.
Frameless patch-hinge doors, by nature of their design, are not completely watertight.
USE OF ANCHORS
Anchors are furnished with every enclosure. However, the use of anchors is not recommended when attaching your enclosure to
a fiberglass unit or wall surrounds with board reinforced mounting areas. Mounting holes in this case should be drilled with an 1/8"
drill bit.
Mounting this unit on tile requires the use of anchors. Special care must be taken not to crack the tile. Before drilling holes in the
tile, lightly chip glazed surface of tile at the desired locations. Drill holes using a 3/16" masonry drill bit. Insert anchors into the
holes making certain that ring on large end of anchor meets the surface of the tile.
CAUTION
Do not attempt to cut mirrors or glass used in this enclosure. Tempered glass and mirrors will shatter if cut.
Care should be taken when standing raw glass on its edge. Glass may shatter if corners are bumped or edge is rested on a
rough floor surface. Cardboard, wood blocks, or a similar surface is a safe resting surface for glass.
CLEANING
Cleaning and care of your enclosure is important to its lasting beauty. A nonabrasive liquid cleaner is recommended.
Never use scouring powder or pads.
SEALING
Seal unit by caulking along outside of enclosure where metal and bath meet, especially where sill meets threshold. If desired, caulk
inside of enclosure where jambs meet walls.
4HJ-GP 10/06
B
A081
HINGE / MAGNETIC
DOOR STOP
G
H810
1 1/4" FLAT
HEAD SCREW
INTERIOR
HANDLE
EXTERIOR
HANDLE
H006
HINGE
B
A081
HINGE / MAGNETIC
DOOR STOP
E
H810
1 1/4" FLAT HEAD
SCREW
G
METAL
SLIDE
C
V678
VINYL
DOOR
SEAL
V001 VINYL DRIP
SWEEP
A001 SILL
MAGNET
HOLDER
WITH
MAGNET
K
MAGNETIC
CATCH
KIT
D
A
F
HANDLE
VINYL
OUTSIDE OF SHOWER
HTG6
PUSH/PULL
HANDLE KIT
L
H002
ANCHOR
H462
2" FLAT HEAD
SCREW
H
Care should be taken when standing raw glass on its edge. Glass may shatter if corners are bumped or edge is rested
on a rough floor surface. Cardboard, wood blocks, or a similar surface is a safe resting surface for glass.
8A x 2" Flat Head Screw
H
(H462 - Used for securing
Patch Hinges to walls)
8A x 1 1/4" Flat Head Screw
G
(H810 - Used for securing Jambs
to walls)
4HJ-GP 10/06
Loading...