Coral Industries 21X1-G User Manual

21X1-G

Bypass Enclosure

PAN HEAD SELF

H900

DRILLING SCREW

O

F

HA12

PULL/

STOP

H342
ROLLER

E

H810
FLAT
HEAD
SCREW

HBAB
TOWEL BAR
BRACKET KIT

H904
PULL/ STOP
LABEL

K

H479

PAN

HEAD

SCREW

H430
TRUSS HEAD SCREW

HA14
TOWEL
BAR
BRACKET

A712

D

TOWEL BAR

A950

C

HEADER

HB01

BUMPER

I

H

H480
PAN HEAD
SCREW

H002
ANCHOR

M

A947

JAMB

B

A925

SILL

PAN HEAD SELF

DRILLING SCREW

A

H900

O

OUTSIDE OF SHOWER

G

HA62
GUIDE

FRAME PACKAGE

KEY DESCRIPTION PART

A SILL A925 1 1
B JAMB A947 2 2
C HEADER A950 1 1
D TOWEL BAR A712 2 1

J VINYL TRACK GUIDE V436 1 1

TOWEL BAR

UNIT

HARDWARE BAG PARTS

E TOWEL BAR BRACKET KIT HBAB 1

L TOWEL BAR/PULL HANDLE KIT HBAH 1

F ROLLER H342 4 4
K 8-32 X 3/8 TRUSS HEAD SCREW H430 4 4
G GUIDE HA62 1 1
H 8A X 1 1/4 PAN HEAD SCREW H480 6 6

I BUMPER HB01 4 4
M ANCHOR H002 6 6
O 8A X 3/8 PAN HD SELF DRILLING SCREW H900 3 3

8A X 1 PAN HEAD SCREW H479 2
8A X 1 1/4 FLAT HEAD SCREW H810 2
PULL / STOP HA12 2
PULL / STOP LABEL H904 2
TOWEL BAR BRACKET HA14 4

8A X 1 PAN HEAD SCREW H479 2
8A X 1 1/4 FLAT HEAD SCREW H810 2
PULL / STOP HA12 2
PULL / STOP LABEL H904 2
PULL HANDLE HA16 2
TOWEL BAR BRACKET HA14 2

TOWEL BAR /

PULL HANDLE

UNIT

V436

J

VINYL TRACK GUIDE

TOOLS

NEEDED

1/8" Drill Bit

3/16" Drill Bit

(3/16" Masonry Bit for

Ceramic Tile)

Scratch Awl

Measuring Tape

Hacksaw

Phillips Screw Driver

Caulking Compound

Masking Tape

File

Drill

Level

21X1-G 10/08

Before starting installation of your new enclosure, carefully read all instructions

and lay out parts to become familiar with their identity.

USE OF ANCHORS

Anchors are furnished with every enclosure. However, the use of anchors is not recommended when attaching your enclosure
to a fiberglass unit or wall surrounds with board reinforced mounting areas. Mounting holes in this case should be drilled with
an 1/8" drill bit.

Mounting of this unit on tile requires the use of anchors. Special care must be taken not to crack the tile. Before drilling holes
in the tile, lightly chip glazed surface of tile at the desired locations. Drill holes using a 3/16" masonry drill bit. Insert anchors
into the holes making certain that ring on large end of anchor meets the surface of the tile.

CLEANING

Cleaning and care of your enclosure is important to its lasting beauty. We suggest using a nonabrasive liquid cleaner.

Never use scouring powder or pads.

SEALING

The use of a caulking compound can assure a water-tight seal when applied along outside edge of the enclosure where metal
and bath meet. If desired, caulk inside of enclosure where jambs meet walls.

Do not try to cut the mirrors or glass used in this enclosure.

Tempered glass and mirrors will disintegrate if cut.

1

Due to the manufacturing process, there may be
rack marks present at one end of your sill and
header. Sill and header must be trimmed to fit
your individual opening. When cutting sill and
header, make certain to trim off end with rack
marks.

Measure wall to wall opening at tub level and cut sill (A)
9/16" less than that measurement. Slide vinyl track
guide (J) into small groove on upright of sill. Trim end
flush with edge of sill.

Locate center of sill. Position guide (G) at center of sill
with curved leg fitting over curve of sill, and back of guide
fitting under small lip on back upright of sill.

Position 1/8" drill bit in small groove on curved leg of
guide. Drill through guide into sill. Secure guide to sill
with 8A x 3/8" pan head screw (O).

Sill (A)

Guide

8A x 3/8" Pan

Head Screw

Place guide at

center of sill.

G

O

INSIDE OF BATH

Measure

A

Sill

A

Vinyl Track

J

Guide

Sill

21X1-G 10/08