Coral Industries 0PJ User Manual
H470
TRUSS HEAD
SCREW
J
DOUBLE CHANNEL
A685
0PJ
A681
ED
MAGNETIC DOOR STOP
G
H170
MAGNETIC
STRIP
PULL
L
HANDLE KIT
C
H470
TRUSS HEAD SCREW
A688
HEADER
J
A682
B
JAMB
OUTSIDE OF SHOWER
FRAME PACKAGE
KEY
DESCRIPTION PART
A SILL A689 1
B JAMB A682 2
C HEADER A688 1
D DOUBLE CHANNEL A685 1
E MAGNETIC DOOR STOP A681 1
F DRIP RAIL A710 1
M DRIP RAIL TAPE
N DRIP RAIL SWEEP VS91 1
G MAGNETIC STRIP H170 1
*
HARDW ARE BAG PARTS
P DRIP RAIL PLUG HA28 1
H ANCHOR H002 8
I 8A X 1 PAN HEAD SCREW H475 8
J 8A X 3/8 TRUSS HEAD SCREW H470 20
K ALLEN WRENCH H635 1
L PUSH/PULL HANDLE KIT HTG6 1
Pre-Installed
*
PLASTIC WASHER 4
EXTERIOR PULL HANDLE 1
INTERIOR PULL HANDLE 1
BUSHING 2
HANDLE CONNECTOR SCREW 2
INTERIOR
HANDLE
HA28
DRIP RAIL
PLUG
P
QTY
HT52 1
EXTERIOR
HANDLE
A710
F
DRIP RAIL
VS91
N
DRIP RAIL SWEEP
TOOLS NEEDED
HT52
DRIP RAIL
TAPE
M
A
1/8" Drill Bit
3/16" Drill Bit
(3/16" Masonry Bit for
Ceramic Tile)
Scratch Awl
Measuring Tape
Hacksaw
Phillips Screw Driver
Caulking Compound
File
Drill
Level
Masking Tape
I
H475
PAN
HEAD
SCREW
A689
SILL
H
H002
ANCHOR
0PJ 6/02
INSTALLATION INSTRUCTIONS
Before starting installation of your new enclosure, carefully read all
instructions and lay out parts to become familiar with their identity.
USE OF ANCHORS
Anchors are furnished with every enclosure. However, the use of anchors is not recommended when attaching your enclosure to a fiberglass
unit or wall surrounds with board reinforced mounting areas. Mounting holes in this case should be drilled with a 1/8" drill bit.
Mounting of this unit on tile requires the use of anchors. Special care must be taken not to crack the tile. Before drilling holes in the tile, lightly
chip glazed surface of tile at the desired locations. Drill holes using a 3/16" masonry drill bit. Insert anchors into the holes making certain that
ring on large end of anchor meets the surface of the tile.
CLEANING
Cleaning and care of your enclosure is important to its lasting beauty. We suggest using a nonabrasive liquid cleaner.
Never use scouring powder or pads.
SEALING
The use of a caulking compound can assure a water-tight seal when applied along outside edge of the enclosure where metal and bath meet.
If desired, caulk inside of enclosure where jambs meet walls.
Do not try to cut the mirrors or glass used in this enclosure. • Tempered glass and mirrors will disintegrate if cut.
Due to the manufacturing process, there may be rack marks present at one end of your sill and
header. All sills and headers must be trimmed to fit individual openings. When cutting sill and
1
header, make certain to trim off end with rack marks.
Measure opening at
threshold of shower and cut
sill (A) to that measurement.
If necessary, file sharp
corners of sill to fit contour of
your unit.
Position sill on center of
threshold with tall edge of sill
toward outside of shower.
Tape sill to threshold with
masking tape to hold in place
while positioning jambs.
When anchors (H) are used,
holes should be drilled using
2
Place jamb (B) on sill with short legs against
wall. If necessary, file sharp corners on back
of jamb to fit contour of your unit.
Align jamb vertically using a level and mark
wall through prepunched holes. Remove
jamb and drill where marked using 1/8" drill
bit. Repeat for remaining jamb on opposite
side.
Reposition jambs on wall and secure using
8A x 1" pan head screws (I).
3/16" drill bit. (Use masonry
bit for tile.)
File sharp
corners of sill
as necessary
to fit contour
of your unit
Sill
A
Masking Tape
Threshold Centerline
OUTSIDE OF SHOWER
Level
B
Jamb
Contour as
needed
OUTSIDE OF SHOWER
Measure
OUTSIDE OF SHOWER
8A x 1" Pan
I
Head Screw
Sill
A
Centerline
0PJ 6/02
Loading...