Coral Industries 063 User Manual
563-GP
Swing Door with Double In-Line Panels
Technical Assistance is available Monday - Friday, 8:00 a.m. - 5:00 p.m. (Central Time)
1-877-723-7190 (Toll Free)
563-GP 2/06
PARTS LIST
FRAME PACKAGE
K EY DESCRIPTION PART QTY
A SILL A855 1
B JAMB A942 2
C HEADER A101 1
D DRIP RAIL A710 / V667 1
E MAGNETIC DOOR STOP A993 1
F DRIP RAIL SWEEP VS91 1
G MAGNETIC STRIP H170 1
H
DRIP RAIL TAPE
*
*
HT52 1
TOOLS NEEDED
1/8" Drill Bit
3/16" Drill Bit
(3/16" Masonry Bit
for Ceramic Tile)
Scratch Awl
Measuring Tape
HARDWARE BAG
I DRIP RAIL PLUG HA28 1
J 8A X 1 PAN HEAD SCREW H475 8
K 8A X 3/8 TRUSS HEAD SCREW H470 24
L ANCHORS H002 8
M+ PULL HANDLE KIT + HSAD 1
EXTERIOR PULL HANDLE HA31 1
INTERIOR PULL HANDLE HA32 1
6-32 X 1 1/4 PAN HEAD SCREW H485 2
* Pre-Installed + May be Pre-Installed
Hacksaw
Phillips Screw Driver
Caulking Compound
File
Drill
Level
Masking Tape
Before starting installation of your new enclosure, carefully read all instructions
and lay out parts to become familiar with their identity.
USE OF ANCHORS
Anchors are furnished with every enclosure. However, the use of anchors is not recommended when attaching your enclosure
to a fiberglass unit or wall surrounds with board reinforced mounting areas. Mounting holes in this case should be drilled with
an 1/8" drill bit.
Mounting of this unit on tile requires the use of anchors. Special care must be taken not to crack the tile. Before drilling holes
in the tile, lightly chip glazed surface of tile at the desired locations. Drill holes using a 3/16" masonry drill bit. Insert anchors
into the holes making certain that ring on large end of anchor meets the surface of the tile.
CLEANING
Cleaning and care of your enclosure is important to its lasting beauty. We suggest using a nonabrasive liquid cleaner.
Never use scouring powder or pads.
SEALING
The use of a caulking compound can assure a water-tight seal when applied along outside edge of the enclosure where metal
and bath meet. If desired, caulk inside of enclosure where jambs meet walls.
Do not try to cut the mirrors or glass used in this enclosure.
Tempered glass and mirrors will disintegrate if cut.
563-GP 2/06
A101
HEADER
MAGNETIC DOOR STOP
C
A993
E
K
H170
G
MAGNETIC STRIP
H470 TRUSS
HEAD SCREW
M
PULL
HANDLE
KIT +
TRUSS HEAD SCREW
H470
K
J
H475
PAN
HEAD
SCREW
B
A942
JAMB
DRIP RAIL
I
HA28
DRIP
RAIL
PLUG
DRIP RAIL SWEEP
OUTSIDE OF SHOWER
A710
D
DRIP RAIL
VS91
HT52
TAPE
H
F
ANCHOR
A855
A
SILL
+ May be Pre-Installed
L
H002
8A x 1 Pan Head Screw
J
(H475 - Used for Jambs)
6-32 x 1 1/4 Pan Head Screw +
M
(H485 - Used for Pull Handle)
8A x 3/8 Truss Head Screw
K
(H470 - Used for securing verticals,
Header, Sill and Drip Rail.
563-GP 2/06
Loading...