COP-USA CM259VAIR-WF User Manual

Client Software

User’s Manual

Index

˄

1 Brief Introduction......................................................................................................................1

2 Installation Guide......................................................................................................................1

3 Software Instructions...............................................................................................................4

3.1 Main Interface.................................................................................................................4

3.2 The function descriptions...........................................................................................7

3.2.1 Toolbar ..................................................................................................................7

3.2.1.1 Image Quality...........................................................................................8

3.2.1.2 OSD.............................................................................................................8

3.2.1.3 Sheltered Area.........................................................................................9

3.2.1.4 Motion Detection...................................................................................10

3.2.2 PTZ Control ........................................................................................................11

3.2.3 Device List..........................................................................................................13

3.2.4 Interface Structure...........................................................................................13

3.2.5 Other Function..................................................................................................13

3.2.5.1 Screen Switch........................................................................................13

3.2.5.2 Client_side Setup..................................................................................14

3.2.5.3 Playback..................................................................................................16

3.2.5.4 Language Version.................................................................................17

3.2.5.5 Full Screen.............................................................................................. 17

3.3 Device property............................................................................................................18

3.3.1 Address/Port......................................................................................................18

3.3.2 DDNS ...................................................................................................................19

3.3.3 PPPoE..................................................................................................................20

3.3.4 Multicast .............................................................................................................21

3.3.5 E-Mail...................................................................................................................22

3.3.6 Date/Time............................................................................................................23

3.3.7 Alarm In...............................................................................................................24

3.3.8 Alarm Out ...........................................................................................................25

3.3.9 PTZ.......................................................................................................................26

3.3.10 Video Channel .................................................................................................27

3.3.11 Audio Channel.................................................................................................28

3.3.12 User....................................................................................................................29

3.3.13 Update...............................................................................................................31

3.3.14 Record...............................................................................................................32

3.3.15 Wireless NIC....................................................................................................33

3.3.16 Miscellaneous

4 Other ..........................................................................................................................................35

4.1 LAN and WAN configuration.....................................................................................35

4.2 Application for DDNS..................................................................................................35

4.3 Router configuration ..................................................................................................35

Appendix A IE mode...............................................................................................................36

UPnP function˅..............................................................34

1 Brief Introduction

The software used to realize the central control for all internet video monitor devices
(including:DVS and IP camera) : monitor, dat a storage, data transfer\manage\control. This
version support 1/4/6/8/9//12/16//20/25/30 display , OSD setting, talkback, record playback,
alarm control and MD, etc. The interface is friendly and easy, can help to control more
than one device in same time. The main functions below:

z Realtime monitor, support CIF/QCIF/Half-D1/D1 format
z Support talkback function
z Support ptz function, allow Pelco D/P and other transparent protocol
z Support alarm /MD/time/ manual trigger record
z Support MD(area/sensitivity optional)/private mask/picture snap
z Support SMTP, send picture to mailbox when alarm
z Support DDNS/PPPoE/DHCP
z Support UPnP,auto configuration port
z Support long distance online upgrade

2 Installation Guide

 System requirement

z Operating System: Windows 2000/XP/Vista
z Processor: Intel Pentium III, 1G or Higher (Pentium IV, 2G or Higher

recommended)

z RAM: 256 MB or more
z Color Monitor: At least DirectX 8.1 or higher and 32M Display storage
z HD: More than 40G

 Software installation

Run the client software DVS_Client_Setup.exe, the window below will pop up:

Design and specification are subject to change without prior notice

1

Select English, and clickǏOKǐ˖

Click ǏNextǐ, the window below will pop up:

Press ǏBrowse…ǐ to change the default path. If you do not want to change, press

Design and specification are subject to change without prior notice

2

ǏInstallǐ.

The below window will pop up:

Then the setup is completed successfully.

Design and specification are subject to change without prior notice

3

3 Software Instructions

3.1 Main Interface

Run DVS Client software, need input password, default is blank. Please refer ǏClient

Setupǐ ĺ Ǐlocal user managementǐfor user name and password change. The interface

as below:

For the first login, user need add the IP address/domain name in order to trigger the
monitor screen, the steps are as follows:

ķ Click

on the right side, pop following dialog:

Design and specification are subject to change without prior notice

4

Mark1: If device not in same network segment, the software can search the IP
address but can’t link. Please change device and pc in same segment.

Mark2: Default IP is 192.168.0.233, gateway is 192.168.0.1.

ĸ Can add device IP address/ Domain name by manual, clickǏaddǐ pop following
dialog:

Ĺ Input device IP/domain name, eg input IP/Host testdvs.3322.org, port 8001,
device type “DVS/IP-CAM”,click ǏOKǐ pop following dialog:

Design and specification are subject to change without prior notice

5

Choose the right device, input user name and password, default is ĺ admin, as

following:

Click Ļ ǏConnectǐ, the right column will display the device address, choose

“channel 1”, hold the left button, drag it to the need window, as following:

Design and specification are subject to change without prior notice

6

3.2 The function descriptions

3.2.1 Toolbar

Followed by login info, talk, sound, snap, record, color, setup, rotation, play.









˖Click to check device user number

/ : Click for Talk off/on

/ : Click for Sound off/on

˖Click for current channel snap

Design and specification are subject to change without prior notice

7

 / : Click to start or off record. Click for record path settingˈ

Click

 ˖Click for brightness/contrast/Saturation/color setting. Default 128 , range

is 0-255







for record playback

/ : Click for current screen off/on

˖Click for screen rotation

˖Click for image quality/OSD/screen mask/MD setting

3.2.1.1 Image Quality

Allow setting frame mode,stream type,frame rate,I frame interval,see below:

ǏCoding StyleǐQualith priority or speed priority

ǏCoding Rateǐ Fixed or dynamic. Fixed on suitable for fixed bandwidth.Dynamic

suitable for record. Default dynamic stream, limits on 100Kbps.

ǏFrame/secondǐ Range is 125ˈdefault 10 Fps.

ǏGap betweem I-framesǐOne I frame in per 100 frame, default 300.

3.2.1.2 OSD

OSD is “on screen display”, mean the info accompany with the image. Allow setting

Design and specification are subject to change without prior notice

8

channel info, time, text color and position.

3.2.1.3 Sheltered Area

Sheltered Area as needed. Hold Ǐctrlǐ to drag mouse choose the area, click

Ǐclearǐ to delete it.

The mask effect as below:

Design and specification are subject to change without prior notice

9

3.2.1.4 Motion Detection

ǏArea settingǐHold Ǐctrlǐ choose the area, max 4 zones allowed.

ǏSensitivityǐSetting high for high sensitivity.

ǏValid Period of TimeǐSetting MD valid period and alarm valid period.

ǏActionǐBuzz, notify client,send e-mail.

ǏOutput toǐChoose the display channel.

Design and specification are subject to change without prior notice

10

3.2.2 PTZ Control

 Click adjust focus

 Click

 Click

 Click up/down/left/right control pan&tliti or hold mouse left key adjust direction by

drag the middle dot

 Preset

position. Click the mouse right key then choose Ǐset current view as a preset

pointǐfor preset .

adjust aperture

adjust lens

˖choose preset from drop down list can control pt to the setting

Design and specification are subject to change without prior notice

11

 Cruise ˖Click setting the route or choose the already one by dr op

down list, click

to stop the cruise.

Click the mouse right key then choose Ǐset current view as a preset pointǐ,pop
following dialog:

Click

, set your cruise route in the following dialog:

Design and specification are subject to change without prior notice

12

3.2.3 Device List

Display connected devices name, domain name, channel name ,etc. Click to

add device. Click
disconnect device.

to pop device property dialog. Click connect or

3.2.4 Interface Structure

Click following button can adjust your own display mode. Click save or click

delete.

3.2.5 Other Function

3.2.5.1 Screen Switch

Click switch display mode,
1/4/6/8/9//12/16//20/25/30 optional

Design and specification are subject to change without prior notice

13

Click to start or stop screen switch ( mean the switch is in process).

3.2.5.2 Client_side Setup

 Client Setup

Click

to setup record path/alarm trigger record period/sound/last time scene.

More than one path can be saved, the top one will be the default record path.

Record up limit 1024M/7200s

 Video Switch Setting

It will realize multi-device or different channels switch in one screen. Click Ǐpageǐ
arrow to add/delete page, clickǏ stayǐ arrow to add/delete standstill period, click

Ǐ

ǐ choose display mode, hold mouse left key drag the wanted channel to the

right column or delete it by double click the channel name.

Design and specification are subject to change without prior notice

14

 Local User Management

Default password is blank. After login, allow add new user and related
password/private. Password will be needed when quit under ǏFull Screenǐ.

Design and specification are subject to change without prior notice

15

 Automatic_Record

Allow time record channel/period setting, save path setting inǏclient setupǐ. The

interface indicator

will blink after start this function.

3.2.5.3 Playback

Click pop following dialog, Search need file through catalog or event list.
Double click to play the file.

Design and specification are subject to change without prior notice

16

Please choose device IP under ǏDevice-side Fileǐthen

clickǏFindǐwhen check file in SD card.

Mark1:Event mean trigger MD or alarm, event record mean MD or alarm trigger
record.

Mark2:Device port file mean file save in linked SD card.

3.2.5.4 Language Version

The software support Chinese and English, click pop to
switch.

3.2.5.5 Full Screen

Click change to full screen mode, all action will be locked under this mode,
input administrator password when quit. Click the right button to pop˖

Choose to pop alarm info

Design and specification are subject to change without prior notice

17

3.3 Device property

Click or choose IP address in device list, click ǏPropertyǐ by right key to
pop dialog, setup or adjust IP addressǃDDNǃPPPoEǃbroadcast configurationǃuser

managementǃupdate online,etc.

3.3.1 Address/Port

Default IP address:192.168.0.233, subnet mask:255.255.255.0ˈgateway:192.168.0.1,
service port 8001. After change, system will register you restart your device to valid the
setup. Change service name not need restart.

Mark1: IP address will valid only after device restart.

Design and specification are subject to change without prior notice

18

Mark2: When link 2 or more devices, need change related IP address and physical
address.

Mark3: Outer net visit need mapping the service port, refer router configuration part.
DNS server needs change to current DNS IP address also.

3.3.2 DDNS

DDNS mean dynamic DNS, for unfixed IP domain name mapping. This client
software support peanut shellǃ3322 and our company DDNS service. Just apply your
domain name in the proper network station(refer to Part3.2) then click ǏOKǐ in the pop
dialog, the DDNS will valid.

ǏDDNS Service Providerǐnow support www.oray.net and www.3322.org.

ǏUser NameǐOne account can apply different domain name, the provider request

not same.

ǏPasswordǐThe related password when you apply the domain name.

ǏDynamic Domain NameǐAccording to domain integrated address.

Design and specification are subject to change without prior notice

19

3.3.3 PPPoE

The client software allow PPPoE . Link the device to phone line through modem,
dial to internet. User can visit the monitor picture by internet from long distance. Choose
PPPoE in following dialog then input user name and password then click ǏOKǐ.

Design and specification are subject to change without prior notice

20

3.3.4 Multicast

Use set device as needed to realize the multicast function.

Design and specification are subject to change without prior notice

21

3.3.5 E-Mail

When choose mail service, the device will send event report and picture to the
appointed mailbox when alarm or MD triggered.

Design and specification are subject to change without prior notice

22

ǏSMTP ServerǐFollow your mailbox hints for related setup.

ǏSMTP Portǐdefault 25.

ǏSender’s AccountǐNeed according to the SMTP service if your mailbox support.

ǏUser Accountǐauto catch account info.

ǏPasswordǐAccount related password.

ǏReceiver’s AccountǐAny mailbox which can receive mail. ClickǏSend A Test Mailǐ

after setup to confirm your action.

Mark: For outlook or foxmail user, need set the sender account to valid the function.

3.3.6 Date/Time

Adjust device date, time. ClickǏSame with PCǐto synchronous with pc.

Design and specification are subject to change without prior notice

23

3.3.7 Alarm In

Design and specification are subject to change without prior notice

24

ǏchannelǐAllow setup name for choosed channel.

ǏActions take to response to alarmǐSound alarm, notice client , send e-mail.

ǏOutput to ǐSetup output channel.

ǏPTZ linkageǐSeperateǃpresetǃcruise. Moniter channel must be appointed when

choose preset or cruise mode.

ǏValid period of timeǐ Setup alarm input time period. + mean valid period,- mean

except the period.

Mark: The record in SD card will lead the real record time add 0-20s base the setting.

3.3.8 Alarm Out

ǏchannelǐAllow setup name for choosed channel

Design and specification are subject to change without prior notice

25

ǏValid period of timeǐSetup alarm output time period. + mean valid period,- mean

except the period

3.3.9 PTZ

ǏVideo Channelǐchoose video channel.

Design and specification are subject to change without prior notice

26

ǏAddressǐMatching the PTZ address with protocol.

ǏProtocolǐSupport Palco-D & Palco-P, default is Palco-D.

ǏStep Lengthǐ Range 1~64, defaul t 32. High speed will make the control hard ,

suggest under 32 for high speed dome.

ǏComm Settingǐ Set baud rate, data bit, stop bit, parity bit.

3.3.10 Video Channel

ǏChannelǐChoose the channel no.

Design and specification are subject to change without prior notice

27

ǏNameǐSetup channel name.

ǏResolutionǐQCIF / CIF / Half_D1 / D1.

ǏPAL/NTSCǐChoose PAL or NTSC.

Mark1: Need restart device to valid new setup.

Mark2: 4 channel DVS only support channel 1 set as D1 format.

3.3.1 1 Audio Channel

Design and specification are subject to change without prior notice

28

ǏChannel NumberǐChoose the channel no.

ǏBits Widthǐ8bits / 16bits / 32bits optional.

ǏSampling Rate ǐThe effect will better with frequency increase.

ǏCompressionǐChoose different mode to compress audio steam( about 10 tims).

Mark: Suggest keep the default setting in normal. Just click
talk back function.

3.3.12 User

Design and specification are subject to change without prior notice

open

29

User management is use to add, delete or modify user name and password, and
setup corresponding authority. User name can only be English character or
number,Chinese is no supported, maximum length of user name or password is 10
characters.

User is separated into three classes:

ƹ Normal User: Admit to brown monitor image, no authority to setup device and
manage user.

ƹ Power User: Admit to setup device, no authority to manage user

ƹ Administrator: Authorized to setup device and manage user. The default

administrator id is admin, password is admin, the id is no allowed to delete.

Design and specification are subject to change without prior notice

30

3.3.13 Update

User can update device local by client or long distance through IE. Device will auto
restart after upgrade. User can check current version no. here.

ǏCurrent version ǐDisplay current version, not allow edit.

ǏFile to uploadǐ ClickǏOpenǐfind the file then clickǏUploadǐ, the following dialog

will show the progress. The device will auto restart after upgrade, not shut off during

the process.

Mark: Online upgrade file DAT is pk2. Firmware program and client program can be
upgrade integrated or separated.

Design and specification are subject to change without prior notice

31

3.3.14 Record

The record property will auto display when link to SD card. In other condition, please
clickǏIPǐĺǏPropertyǐĺǏRecordǐto pop the dialog:

Set file limit, 0 mean no limit

Valid record period

Mark1: Please cut off device before plug SD card.

Mark2: Choose FAT32 type when form at SD card.

Mark3: Click

presentation:

choose ǏDevice-Side Fileǐ to review record, see diagrammatic

Design and specification are subject to change without prior notice

32

3.3.15 Wireless NIC

Wireless network card property will auto display; in other condition click ǏIPǐĺ

ǏPropertyǐĺǏRecordǐ to pop the dialog:

Design and specification are subject to change without prior notice

33

3.3.16 Miscellaneous˄UPnP function

˅

UPnP( Universal Plug and Play), the router will auto mapping TCP and UDP port.

Mark1: Router must support UPnP function

Mark2: Recommend external port between 1025-32767

Design and specification are subject to change without prior notice

34

4 Other

4.1 LAN and WAN configuration

i LAN automatically search

Run DVS Client, Click
device list. Only PC and video server in same network segment can connect.

If there are no device in the device list, make sure the following question:

If DVS is already powered?ķ
If DVS and PC have been normal connected? If yes, the light will be long bright or ĸ

flashing.

If PC has firewall working? If yes, should do it agaĹ in after closing the firewall.

i WAN manually search

If users want to login in another subnet, the device can not automatically be searched.
The video device should be manually added as the following steps:

Register DDNS services from a DDNS service proviķ der. After applications a

domain name will be assigned, and an account number and password will be obtained.

Click mouse right key in device list up item, choose ĸ ǏPropertyǐĺǏDDNSǐ set

your domain info ,please see 3.3.2 for details.

When Internet IP is Ĺ changed. The device will automatically tell DDNS server its

, the video server in the local LAN will appear in the

new Internet IP.

Users only input domain in the network browser can run Client.ĺ

4.2 Application for DDNS

Normally users use dynamic IP address in the internet. User can use a static
hostname instead of a dynamic IP address to monitor Lan device image. In this way, user
should register a domain name and obtain a password. The device supports

www.3322.org

doing it, set your domain info as 3.3.2 for details.

and www.dyndns.org , users can login it and register the domain, after

4.3 Router configuration

Routers must be set to enable a PC TCP connecting to the device. Routers use port
number to decide which device request is allowed, this function is port transmitting or

Design and specification are subject to change without prior notice

35

virtual services.

Appendix A IE mode

When first visit device through IE, user need add http:// by manual to pop the
following dialog:

ClickǏ

Then input user name and password (default is admin ) can get monitor page, see below:

Design and specification are subject to change without prior notice

ǐ download the client and control , then install it.

36

Storage IP Box Camera

User’s Manual

Note: WIFI function is an option of IP camera

Index

˄

1 PRODUCT OVERVIEW ....................................................................................................................1

ERFORMANCE..............................................................................................................................1

1.1 P

1.2 I

NTERFACE.....................................................................................................................................2

2 CLIENT SOFTWARE INSTALLATION GUIDE.............................................................................3

3. CLIENT SOFTWARE INSTRUCTIONS GUIDE...........................................................................5

AIN INTERFACE ...........................................................................................................................5

3.1 M

3.2 T

HE FUNCTION DESCRIPTIONS ......................................................................................................8

3.2.1 Toolbar.................................................................................................................................8

3.2.2 PTZ Control....................................................................................................................... 11

3.2.3 Device List.........................................................................................................................13

3.2.4 Interface Structure..........................................................................................................13

3.2.5 Other Function.................................................................................................................13

3.3 D

EVICE PROPERTY.......................................................................................................................17

3.3.1 Address/Port.....................................................................................................................17

3.3.2 DDNS..................................................................................................................................18

3.3.3 PPPoE.................................................................................................................................19

3.3.4 Multicast............................................................................................................................20

3.3.5 E-Mail..................................................................................................................................21

3.3.6 Date/Time...........................................................................................................................21

3.3.7 Alarm In..............................................................................................................................22

3.3.8 Alarm Out...........................................................................................................................23

3.3.9 PTZ......................................................................................................................................24

3.3.10 Video Channel................................................................................................................25

3.3.1 1 Audio Channel................................................................................................................26

3.3.12 User...................................................................................................................................27

3.3.13 Update..............................................................................................................................28

3.3.14 Record..............................................................................................................................29

3.3.15 Wireless NIC(optional).................................................................................................30

3.3.16 Miscellaneous

UPnP function˅.............................................................................31

4 OTHER...............................................................................................................................................32

4.1 LAN

4.2A

4.3 R

AND WAN CONFIGURATION................................................................................................32

PPLICATION FOR DDNS............................................................................................................33

OUTER CONFIGURATION............................................................................................................33

APPENDIX A IE MODE...................................................................................................................33

1 Product Overview

Storage IP box Camera is an embedded device designed for network video

surveillance application. Optimized H.264 video compression algorithm assures clearer
and more fluent image transmission. It uses the newest techniques and high integration
single chip SOC with powerful Linux RTOS (Real-time Operating System) realized high
performance and low cost digital multimedia process. Built-in mini Web Server (38x38mm
double boards) that allows users to conveniently carry out remote control via Internet
Explorer. Furthermore, central management software can be used for integrated
surveillance and management of multiple network cameras, so it is very easy to build
large video surveillance system.

1.1 Performance

z high-density and programmable communication media processor Hi3510, SOC

single chip solution, equipped with two processors,ARM9 and DSP

z Support both high sensitivity SONY CCD or other CMOS sensor

z H.264 baseline profile@Level 2.2, realize transmission of High Definition video over

low network bandwidth easily

z Up to 30fps(NTSC) or 25fps(PAL)

z Up to 30 viewers can directly access the camera simultaneously

z Built-in Web server enables the use of a standard Web browser for viewing and

management

z Support SD card video/picture storage

z Support remote software upgrade safely function

z Support dynamic IP address , LAN, Internet (ADSL and Cable Modem)

z Network protocols: HTTP, SMTP, PPPoE, DDNS, DNS, DHCP, UPnP(CP for NAT)

z Support Bi-directional real- time transmission of audio talk-back &broadcast

z Network self-adapting technology to adjust video frame rate automatically according

to the network bandwidth

z Provide motion detection/shelter /sensor alarm functions (Area & Sensitivity can be

set )

Design and specification are subject to change without prior notice

1

z Provide RS485 serial port with several built-in high-speed domes and decoder

˖

˖

˖

˖

˖

˖

˖

˖

˖

˖

˖

˖

protocols, supports transparent protocols.

1.2 Interface

DC12V
RST
LAN
A in
A out
SD Card

RS485
GND

ALM In
ALM Out
AUTO IRIS
ANT

Storage IP box Camera (Back)

Power Supply, DC 12V/1.5A
Reset Button
Ethernet Port

Audio Input

Audio Output

SD Card slot

485 Control interface, connect to Pan/Tilt or encoder, support many protocols

Signal ground, alarm ground, RS485 ground

1 Alarm Input

2 Alarm output

Auto Iris port, support DC Lens

WiFi interface(optional)

Design and specification are subject to change without prior notice

2

2 Client Software Installation Guide

 System requirement

z Operating System: Windows 2000/XP/Vista
z Processor: Intel Pentium III, 1G or Higher (Pentium IV, 2G or Higher

recommended)

z RAM: 256 MB or more
z Color Monitor: At least DirectX 8.1 or higher and 32M Display storage
z HD: More than 40G

 Software installation

Run the client software DVS_Client_Setup.exe, the window below will pop up:

Select English, and clickǏOKǐ˖

Design and specification are subject to change without prior notice

3

Click ǏNextǐ, the window below will pop up:

Press ǏBrowse…ǐ to change the default path. If you do not want to change, press

ǏInstallǐ.

The below window will pop up:

Then the setup is completed successfully.

Design and specification are subject to change without prior notice

4

3. Client Software Instructions Guide

3.1 Main Interface

Run DVS Client software, need input password, default is blank. Pls refer ǏClient

Setupǐ ĺ Ǐlocal user managementǐfor user name and password change. The interface

as below:

For the first login, user need add the IP address/domain name in order to trigger the
monitor screen, the steps are as follows:

Clickķ

on the right side, pop following dialog:

Design and specification are subject to change without prior notice

5

Mark1: If device not in same network segment, the software can search the IP
address but can’t link. Please change device and pc in same segment.

Mark2: Default IP is 192.168.0.233, gateway is 192.168.0.1.

Can add device IP address/ Domain name by manual, clickĸ Ǐaddǐ pop following

dialog:

Input device IP/domain name, eg input IP/Host testdvs.3322.org,Ĺ port 8001,

device type “DVS/IP-CAM”,click ǏOKǐ pop following dialog:

Design and specification are subject to change without prior notice

6

Choose the right device, input user name and password, default is ĺ admin, as

following:

Click Ļ ǏConnectǐ, the right column will display the device address, choose

“channel 1”, hold the left button, drag it to the need window, as following:

Design and specification are subject to change without prior notice

7

3.2 The function descriptions

3.2.1 Toolbar

Followed by login info, talk, sound, snap, record, color, setup, rotation, play.











 ˖Click for brightness/contrast/Saturation/color setting. Default 128 , range



˖Click to check device user number

/ : Click for Talk off/on

/ : Click for Sound off/on

˖Click for current channel snap

/ : Click to start or off record. Click for record path settingˈ

Click

is 0-255

for record playback

/ : Click for current screen off/on





˖Click for screen rotation

˖Click for image quality/OSD/screen mask/MD setting

3.2.1.1 Image Quality

Allow setting frame mode,stream type,frame rate,I frame interval,see below:

ǏCoding StyleǐQualith priority or speed priority

ǏCoding Rateǐ Fixed or dynamic. Fixed on suitable for fixed bandwidth.Dynamic

suitable for record. Default dynamic stream, limits on 100Kbps.

ǏFrame/secondǐ Range is 125ˈdefault 10 Fps.

ǏGap betweem I-framesǐOne I frame in per 100 frame, default 300.

Design and specification are subject to change without prior notice

8

3.2.1.2 OSD

OSD is “on screen display”, mean the info accompany with the image. Allow setting
channel info, time, text color and position.

Design and specification are subject to change without prior notice

9

3.2.1.3 Sheltered Area

Sheltered Area as needed. Hold Ǐctrlǐ to drag mouse choose the area, click

Ǐclearǐ to delete it.

The mask effect as below:

3.2.1.4 Motion Detection

ǏArea settingǐHold Ǐctrlǐ choose the area, max 4 zones allowed.

ǏSensitivityǐSetting high for high sensitivity.

ǏValid Period of TimeǐSetting MD valid period and alarm valid period.

ǏActionǐBuzz, notify client,send e-mail.

ǏOutput toǐChoose the display channel.

Design and specification are subject to change without prior notice

10

3.2.2 PTZ Control

 Click adjust focus

 Click

 Click

 Click up/down/left/right control pan&tliti or hold mouse left key adjust direction by

drag the middle dot

 Preset

position. Click the mouse right key then choose Ǐset current view as a preset

pointǐfor preset .

adjust aperture

adjust lens

˖choose preset from drop down list can control pt to the setting

Design and specification are subject to change without prior notice

11

 Cruise ˖Click setting the route or choose the already one by dr op

down list, click

to stop the cruise.

Click the mouse right key then choose Ǐset current view as a preset pointǐ,pop
following dialog:

Click

, set your cruise route in the following dialog:

Design and specification are subject to change without prior notice

12

3.2.3 Device List

Display connected devices name, domain name, channel name ,etc. Click to

add device. Click
disconnect device.

to pop device property dialog. Click connect or

3.2.4 Interface Structure

Click following button can adjust your own display mode. Click save or click

delete.

3.2.5 Other Function

3.2.5.1 Screen Switch

Click switch display mode,
1/4/6/8/9//12/16//20/25/30 optional

Design and specification are subject to change without prior notice

13

Click to start or stop screen switch ( mean the switch is in process).

3.2.5.2 Client_side Setup

 Client Setup

Click

to setup record path/alarm trigger record period/sound/last time scene.

More than one path can be saved, the top one will be the default record path.

Record up limit 1024M/7200s

 Video Switch Setting

It will realize multi-device or different channels switch in one screen. Click Ǐpageǐ
arrow to add/delete page, clickǏ stayǐ arrow to add/delete standstill period, click

Ǐ

ǐ choose display mode, hold mouse left key drag the wanted channel to the

right column or delete it by double click the channel name.

Design and specification are subject to change without prior notice

14

 Local User Management

Default password is blank. After login, allow add new user and related
password/private. Password will be needed when quit under ǏFull Screenǐ.

Design and specification are subject to change without prior notice

15

 Automatic_Record

Allow time record channel/period setting, save path setting inǏclient setupǐ. The

interface indicator

will blink after start this function.

3.2.5.3 Playback

Click pop following dialog, Search need file through catalog or event list.
Double click to play the file.

Please choose device IP under ǏDevice-side Fileǐthen

clickǏFindǐwhen check file in SD card.

Design and specification are subject to change without prior notice

16

Mark1:Event mean trigger MD or alarm, event record mean MD or alarm trigger
record.

Mark2:Device port file mean file save in linked SD card.

3.2.5.4 Language Version

The software support Chinese and English, click pop to
switch.

3.2.5.5 Full Screen

Click change to full screen mode, all action will be locked under this mode,
input administrator password when quit. Click the right button to pop˖

Choose to pop alarm info

3.3 Device property

Click or choose IP address in device list, click ǏPropertyǐ by right key to
pop dialog, setup or adjust IP addressǃDDNǃPPPoEǃbroadcast configurationǃuser

managementǃupdate online,etc.

3.3.1 Address/Port

Default IP address:192.168.0.233, subnet mask:255.255.255.0ˈgateway:192.168.0.1,
service port 8001. After change, system will register you restart your device to valid the
setup. Change service name not need restart.

Design and specification are subject to change without prior notice

17

Mark1: IP address will valid only after device restart.

Mark2: When link 2 or more devices, need change related IP address and physical
address.

Mark3: Outer net visit need mapping the service port, refer router configuration part.
DNS server needs change to current DNS IP address also.

3.3.2 DDNS

DDNS mean dynamic DNS, for unfixed IP domain name mapping. This client
software support peanut shellǃ3322 and our company DDNS service. Just apply your
domain name in the proper network station(refer to Part3.2) then click ǏOKǐ in the pop
dialog, the DDNS will valid.

Design and specification are subject to change without prior notice

18

ǏDDNS Service Providerǐnow support www.oray.net and www.3322.org.

ǏUser NameǐOne account can apply different domain name, the provider request

not same.

ǏPasswordǐThe related password when you apply the domain name.

ǏDynamic Domain NameǐAccording to domain integrated address.

3.3.3 PPPoE

The client software allow PPPoE . Link the device to phone line through modem,
dial to internet. User can visit the monitor picture by internet from long distance. Choose
PPPoE in following dialog then input user name and password then click ǏOKǐ.

Design and specification are subject to change without prior notice

19

3.3.4 Multicast

Use set device as needed to realize the multicast function.

Design and specification are subject to change without prior notice

20

3.3.5 E-Mail

When choose mail service, the device will send event report and picture to the
appointed mailbox when alarm or MD triggered.

ǏSMTP ServerǐFollow your mailbox hints for related setup.

ǏSMTP Portǐdefault 25.

ǏSender’s AccountǐNeed according to the SMTP service if your mailbox support.

ǏUser Accountǐauto catch account info.

ǏPasswordǐAccount related password.

ǏReceiver’s AccountǐAny mailbox which can receive mail. ClickǏSend A Test Mailǐ

after setup to confirm your action.

Mark: For outlook or foxmail user, need set the sender account to valid the function.

3.3.6 Date/Time

Design and specification are subject to change without prior notice

21

Adjust device date, time. ClickǏSame with PCǐto synchronous with pc.

3.3.7 Alarm In

ǏchannelǐAllow setup name for choosed channel.

ǏActions take to response to alarmǐSound alarm, notice client , send e-mail.

ǏOutput to ǐSetup output channel.

ǏPTZ linkageǐSeperateǃpresetǃcruise. Moniter channel must be appointed when

choose preset or cruise mode.

ǏValid period of timeǐ Setup alarm input time period. + mean valid period,- mean

except the period.

Design and specification are subject to change without prior notice

22

Mark: The record in SD card will lead the real record time add 0-20s base the setting.

3.3.8 Alarm Out

ǏchannelǐAllow setup name for choosed channel

ǏValid period of timeǐSetup alarm output time period. + mean valid period,- mean

except the period

Design and specification are subject to change without prior notice

23

3.3.9 PTZ

ǏVideo Channelǐchoose video channel.

ǏAddressǐMatching the PTZ address with protocol.

ǏProtocolǐSupport Palco-D & Palco-P, default is Palco-D.

ǏStep Lengthǐ Range 1~64, defaul t 32. High speed will make the control hard ,

suggest under 32 for high speed dome.

ǏComm Settingǐ Set baud rate, data bit, stop bit, parity bit.

Design and specification are subject to change without prior notice

24

3.3.10 Video Channel

ǏChannelǐChoose the channel no.

ǏNameǐSetup channel name.

ǏResolutionǐQCIF / CIF / Half_D1 / D1.

ǏPAL/NTSCǐChoose PAL or NTSC.

Design and specification are subject to change without prior notice

25

Mark1: Need restart device to valid new setup.

Mark2: 4 channel DVS only support channel 1 set as D1 format.

3.3.1 1 Audio Channel

ǏChannel NumberǐChoose the channel no.

ǏBits Widthǐ8bits / 16bits / 32bits optional.

ǏSampling Rate ǐThe effect will better with frequency increase.

ǏCompressionǐChoose different mode to compress audio steam( about 10 tims).

Design and specification are subject to change without prior notice

26

Mark: Suggest keep the default setting in normal. Just click
talk back function.

open

3.3.12 User

User management is use to add, delete or modify user name and password, and
setup corresponding authority. User name can only be English character or
number,Chinese is no supported, maximum length of user name or password is 10
characters.

User is separated into three classes:

ƹ Normal User: Admit to brown monitor image, no authority to setup device and

manage user.

Power User: Admit to setup device, no authority to manage userƹ

Design and specification are subject to change without prior notice

27

Administrator: Authorized to setup device and manage user. The defaultƹ

administrator id is admin, password is admin, the id is no allowed to delete.

3.3.13 Update

User can update device local by client or long distance through IE. Device will auto
restart after upgrade. User can check current version no. here.

ǏCurrent version ǐDisplay current version, not allow edit.

ǏFile to uploadǐ ClickǏOpenǐfind the file then clickǏUploadǐ, the following dialog

will show the progress. The device will auto restart after upgrade, not shut off during

the process.

Design and specification are subject to change without prior notice

28

Mark: Online upgrade file DAT is pk2. Firmware program and client program can be
upgrade integrated or separated.

3.3.14 Record

The record property will auto display when link to SD card. In other condition, please
clickǏIPǐĺǏPropertyǐĺǏRecordǐto pop the dialog:

Design and specification are subject to change without prior notice

29

Valid record period

Set file limit, 0 mean no limit

Mark1: Please cut off device before plug SD card.

Mark2: Choose FAT32 type when form at SD card.

Mark3: Click

presentation:

choose ǏDevice-Side Fileǐ to review record, see diagrammatic

3.3.15 Wireless NIC(optional)

Wireless network card property will auto display; in other condition click ǏIPǐĺ

ǏPropertyǐĺǏRecordǐ to pop the dialog:

Design and specification are subject to change without prior notice

30

3.3.16 Miscellaneous˄UPnP function

˅

UPnP( Universal Plug and Play), the router will auto mapping TCP and UDP port.

Design and specification are subject to change without prior notice

31

Mark1: Router must support UPnP function

Mark2: Recommend external port between 1025-32767

4 Other

4.1 LAN and WAN configuration

i LAN automatically search

Run DVS Client, Click
device list. Only PC and video server in same network segment can connect.

If there are no device in the device list, make sure the following question:

If DVS is already powered?ķ
If DVS and PC have been normal connected? If yes, the light will be long bright or ĸ

, the video server in the local LAN will appear in the

Design and specification are subject to change without prior notice

32

flashing.

If PC has firewall working? If yes, should do it again after closing the firewall.Ĺ

i WAN manually search

If users want to login in another subnet, the device can not automatically be searched.
The video device should be manually added as the following steps:

Register DDNS services from a DDNS service provider. After applications a ķ

domain name will be assigned, and an account number and password will be obtained.

Click mouse right key in device list up item, choose ĸ ǏPropertyǐĺǏDDNSǐ set

your domain info ,please see 3.3.2 for details.

When Internet IP is changed. The device will automatically telĹ l DDNS server its

new Internet IP.

Users only input domain in the network browser can run Client.ĺ

4.2 Application for DDNS

Normally users use dynamic IP address in the internet. User can use a static
hostname instead of a dynamic IP address to monitor Lan device image. In this way, user
should register a domain name and obtain a password. The device supports

www.3322.org

doing it, set your domain info as 3.3.2 for details.

and www.dyndns.org , users can login it and register the domain, after

4.3 Router configuration

Routers must be set to enable a PC TCP connecting to the device. Routers use port
number to decide which device request is allowed, this function is port transmitting or
virtual services.

Appendix A IE mode

When first visit device through IE, user need add http:// by manual to pop the
following dialog:

Design and specification are subject to change without prior notice

33

ClickǏ

ǐ download the client and control , then install it.

Then input user name and password (default is admin ) can get monitor page, see below:

Design and specification are subject to change without prior notice

34