COP-USA CD69IRICR-1K User Manual
Specification
Model
Pick up Element
Effective Picture Elements
(H×V)
Resolution
Minimum Illumination
S/N Ratio
Scanning System
Synchronous System
Auto Electronic Shutter
Gama Characteristic
IR Distance
Video Output
Auto Gain Control
Power/Current
Lens
CD69IRICR-1K
1/3" SONY 1.3 Megapixel Sensor
1305(H) X1049(V)
1000TVL
0.01 Lux/F1.2
0Lux (with IR LED ON)
More than 50dB
Progressive
Internal, Negative sync.
NTSC: 1/60s~1/100,000s, PAL: 1/50s~1/100,000s
0.45
30 Meters (with ￠5X36 PCS Infrared LED)
1Vpp, 75Ω
Auto
DC12V(+/-10%)/450mA
2.8-12mm （2.0 Megapixel） Manual Zoom Lens
CD69IRICR-1K Color Camera
Vandalproof IR Dome Color Camera
Dimension (mm)
Weight (g)
Storage Temperature
Operating Temperature
￠131x 93(H)
800
-30~+60℃ RH95% MAX
-10~+50℃ RH95% MAX
Packing List
No
1.
Vandalproof IR Dome Color Camera CD69IRICR-1K 1
2.
Name Model Number
User Guide
CD69IRICR-1K
Franchiser：
Easily adjustable
Zoom
Notes:Before providing power for the
Easily adjustable
Focus
camera, please read this User Guide in
detail!
Do not attempt to disassemble the camera.
If the camera can not work, please contact
1
local franchiser or our company.
BRIEF OF PRODUCT
CONNECTING
INTRODUCTION
* Sensor (SONY 138)
Adopt SONY 1/3" Sensor.
* Auto Gain Control (AGC)
Built-in auto gain control (AGC) circuit. The color camera
can get high definition picture in low Lux condition.
* Scanning Mode
NTSC or PAL mode.
* Support UTC function
With UTC Remote Controller for the convenience of
OSD menu setting.
* OSD SETTING
3D-NR ON/OFF
GLOBAL/CENTER/CENTERWEIGHT/BLACK
LIGHT/FRONT LIGHT/DISTINGUISH
MOSAIC/WHITE/YELLOW/CYAN/GREEN/
MAGENTA/RED/BLUE/BLACK
IMAGE
DAY&NI
GHT
WB
OSD
SET
ZONE
MASK-
ING
DIREC-
TION
LAN-
GUAGE
LOAD DEFAULT
SOFT VERION
SAVE&EXIT
AE MODE
IMAGE ENHANCE SHARPNESS/CONTRAST/SATURATION
MIRROR ON/OFF
FLIP ON/OFF
BRIGHTNESS 0.10.20......250
ZOOM IN 50. 60. 70. 80. 90. 100
AUTO
IR-CUT
AWB-PRO
AWB-TEMPORA L
AWB-AI
AWB-SZ
AWB-GW
AWB-CCT
COLOR
AREA NO.0 - AREA
NO.7
AREA NO.0 - AREA
NO.3
ENGLISH
CHINESE
LEFT
KEY BOARD
UP
DOWN
Monitor
RIGHT
CD69IRICR-1K
MENU
Link wire rule：
Video
Power
PRESS
DC12V Power Supply
Video
DC12V
TROUBLE AND SOLUTION
1. No Picture after providing power
. May be the power supply voltage abnormity, please check the power
supply voltage and pole whether exactitude.
. Please check all the connecting cable and monitors whether be connected
correctly or not.
2. The picture level direction have flowing interference ripples
. May be caused by the power supply AC ripples, it need filter the wave of the
power supply.
. Check the monitor and peripheral equipments used.
3. The picture background color changes continuously
. The fluorescent lamp’s electromagnetic field cause color roll. This is proper
phenomenon of the cameras.
. Reduce the fluorescent lamp numbers or increase the distance between the
camera and the fluorescent lamps can improve it.
. Use power supply external sync. camera can solve it.
4. The picture smear too mass
. The power supply’s voltage unstable.
. Connecting cables not connect correctly or have high impedance.
Notes：
●The power supply must through safe attestation. Its output voltage,
current, voltage polarity and operating temperature must match the
camera’s requirement.
●When using the camera in the thunderbolt condition,please note to
mount Anti-thunder device or put off the power supply plug and cable.
●In order to capture high quality pictures, the power supply’s cable and
video output cable should not be too long.
Congratulations on your purchase of this product.
This User Guide suits CD69IRICR-1K product. We adopt
the latest SONY technical of sensor and driver. The most
attractive characteristics are small and easy hidden, suits
the elevator and corridor. In addition, it owns the characters of high definition and stability, strong anti-jamming,
rich and real color. Fixing and using this model are convenient too. It is very good for you to apply to your CCTV
system.
Please read this instruction manual carefully to en-
sure proper use of the product.
To prevent fire or shock hazarded. Do not expose the unit
to rain or moisture.
The symbol is intended to alert the user to the presence of
important operating and maintenance (servicing)
Instructions in the literature accompanying the appliance.
The symbol is intended to alert the user to the presence of
uninsulated ‘dangerous voltage’ within the product’s
enclosure that may be of sufficient Magnitude to constitute
a risk of electric shock to persons.
RISK OF ELECTRIC. DO NOT OPEN
SHOCK
DO NOT REMOVE COVER OR BACK NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
CAUTION: TO PREVENT ELECTRIC SHOCKS AND RISK OF
FIRE HAZARDS, DO NOT USE OTHER THAN
SPECIFIED POWER SOURCE.
Notes:
● Please note the camera’s operating temperature and its using
environment
too low temperatures. The operating temperature is -30~+60℃.
(Recommendatory operating temperature is -10~+50℃.)
● Never make the camera face the sun or bright object. Otherwise, it will damage the CMOS.
● Do not mount the camera near by the radiator or heater.
Specifications Subject to Change Without Notice. All Logos,
Trademarks and Copyrights belongs to their respective owners.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
requirement. Avoid using the camera at too high or
CAUTION:
Loading...