Installation Manual For Mini High Speed
Dome Camera
Please read the operation manual carefully before installing and using
SAFETY PRECAUTIONS
CAUTION:
TO REDUCE THE RISK OF ELECTRI CAL SHOCK, DO DOT
OPEN COVERS. NO USER SERVICEABLE PARTS I NSIDE.
REFER SERVICI NG TO QUALI FIED SERVICE PERSONNEL
The l i ght i ng f l ash wi t h a arr owhead symbol , i n an
equi l at eral tr i angl e, i s i ntended t o al ert t he user .
There i s uni nsul at ed “ danger ous vol t age” presence
near by t he product ' s encl osure whi ch may be r i sk of
t o per sons .
The ex c l amat i on poi nt wi t hi n an equi l at er al
t r i angl e i s i nt ended t o al ert the user t o ref er ence
of t he i mpor t a nt oper at i ng and ma i nt enanc e
(servi ci ng ) i nst r uct i ons .
CAUTION
RISK OF ELECTRI C
SHOCK. DO NOT OPEN!
THE PRODUCT CODE MARKED ON THE BOTTOM COVER. PLEASE
FILL THE CODE I N THE FOLLOWI NG BLANK. PLEASE SAVING
THI S SPECI FI CATI ON CAREFULLY, SO THAT CHECKING.
MODEL:________________________
PRODUCT CODE:________________________
V2.0
Contents
Notice ………………………………………………………………….……………………….1
I Description of Functions…………………..………………………………………………2
1.1 Dome Specification………………………………….……………………………….2
1.2 Camera Specification……………………………….………………………………..3
1. 3 Dom e Fu n c t io n s …… … … ……… … … …… … . .… … … …… … … … …… … . . 4
II Setup of the Menu………………………………………..……………………………5
2.1 Main Menu………………………………………….…..…………………………….5
2. 2 S ystem Setup ………………………………………….. ……………… ………….. 5
2.3 Display Setup………………………………………………………………………….6
2.4 Camera Setup………………………………………..……………………………….7
2.5 Motion Setup………………………………………….……………………………..8
2.6 Privacy Mask……………………………………………..………………………….10
2.7 Advance Setup…………………………………………………………………………10
III Setup of the Dome Camera……………………………………………………………13
3.1 Connection of the System……………………………………………………………13
3.2 Dip Switch……………………………………………………………………………14
3.3 Protocol and the Default Baud Rate………………………………………………….15
3.4 Setup of the Baud Rate………………………………………………………………16
3.5 Selection of the Terminal Resistor……………………………………………………16
3.6 Special Control………………………………………………………………………16
IV Installation……………………………………………………………………………17
4.1 Safety Measure………………………………………………………………………17
4.2 Warning………………………………………………………………………………17
4.3 Ambient Requirement…………………………………………………………………17
4.4 Preparation……………………………………………………………………………18
4.5 Brief of the Installation………………………………………………………………18
4.6 Installation of the Dome………………………………………………………………19
4.7 Dismounting of the Black Cover………………………………………………………22
4.8 Installation of the camera module……………………………………………………23
4.9 Wire Out………………………………………………………………………………26
Appendix:
I Trouble shooting………………………………………………………………………27
II Lightning and surging Protection………………………………………………………28
III Cleaning of the cover…………………………………………………………………28
IV RS485 Bus Basic Knowledge…………………………………………………………29
-
Notice
Please read this manual carefully, before you install and use the dome camera.
Electric safety
Please act on the national electric standard when you installing and using this product. To be sure
the power adaptor is original, it is DC12V/2A.
Transportation
The stress, strenuous vibration and water logging will damage the products under the
transportation, storage and installation. The integrity packaging can protect the product, otherwise
vendor will not pay for the damage.
Installation
Please install this product follow the manual, to take the camera module carefully, do not extrusion
the structure. The dome cover is an optical part, please do not touch it by hand.
Staff quality
Only the qualified serviceman or system installation people can install this product.
Do not take down the dome camera arbitrarily
Only the qualified serviceman or system installation people can take down the product.
Ambient requirement
Ambient Temperature: indoor 0～+40, outdoor -35～+55
Humidity: 10-75％ Air pressure: 86-106kpa Power supply: DC12V/2A
Installation requirement
Please do not take arm the camera module to the bright objects, even the dome camera is
power off.
Please install the product on an enough tolerance position.
Please do not use the strong or abrasive scour to clean the dome, the neutral scour is accept.
Please do not use the indoor product in the outdoor place, the product will be damaged.
Please keep the enough distance from the RS485 wires to the high voltage equipment and
cable, and the protection of the lightning strike and surge is necessary.
Please do not try to repair the defective product, the trouble shooting can help you to find the
problem, and only the authorized service people can fix and repair the product.
Please use the only lens tissue to clean the camera lens.
- 1
-
I. Description of Functions
The intelligent dome camera is a hi-tech CCTV product which incorporates high-clarity color camera,
panoramic speed-variable PAN/TILT, multifunctional decoder, universal character generator, CPU
processor, memory chip into a whole. It can largely reduce connection and installation processes of
components in the system, rise up reliability of the system and facilitate installation and maintenance.
Therefore it has advantages of beautiful appearance, compact structure and easy operation.
1.1 High speed dome
Power supply DC12V/2A
Power consumption 12VA
Preset position 128
Cruising track 6
Pattern 3
Alarm 4 input & 1 output
Auto overturning
The camera will rotate 180°automatically, when it reaches
the vertical position.
Pan scanning
Pan speed
Pan range
Tilt range
Tilt speed
360°programmable
0° -- 300°/s
360°continuously
0-- 90°
0° -- 120°/s
Communication RS485
Baud rate 2400/4800/9600/19200 bps
Fan / heater Auto (only for outdoor)
Relative humidity
Work temperature
10-75%（without agglomeration）
Indoor：0℃ — +40℃
Outdoor：–35℃ -- +55℃
- 2
-
1.2 Camera Specification
Camera
Image sensor
Scan system
Horizontal
resolution
Synchronization
PAL 795(H)x596(V) 470K
Active
pixels
NTSC
Min. illumination
2000-Z
Color
Internal
1/3″Color CCD
2:1 interval line scan
650 TVL
752(H)x 582(V) 440K
0.02Lux
10×
Optical
Visible angle
Digital Zoom
Visible angle
S/N Ration
Video Output
f=3.6 to 36 mm
0
Wide: 51.2°
TELE: 5.58°
＞
52dB
BNC 1.0Vp-p/75
Ω
- 3
-
1.3 Dome Functions
Multi protocol decoder integrated
a. built-in the multi protocol decoder, including maximum 16 protocols with optional baud rates
from 2400bps to 19200bps.
b. RS485 data communication, dome addresses (ID): 1～511.
Omni bearing Pan/tilt
a. 360º panning, panning speed: 0.2～300rad/s,
b. 0～90º tilting，tilting speed: 120rad/s,
c. low speed running smoothly, low noise.
Intelligent functions
a. 128 preset positions, power off memory function.
b. Line scanning function, with adjustive speed.
c. 6 cruising tracks, each cruising track has 16 preset positions with adjustive residence time.
d. 3 Pattern tours, 120 seconds for each, with power off memory function.
e. Alarm function, 4 alarm in and 1 alarm out.
f. Angle display, including the panning, tilting and camera view angles.
g. Power recovery.
h. Temperature display.
i. Password protection for the menu.
j. Long distance dome address modification. The address of the dome can be modified by RS485,
the rules are as the following.
k.The dip switcher address is the hardware address (HID), the address we change by RS485 is the
software address (SID).The HID and SID is same when we produce it. (ie: HID=SID=001) If
we change the SID to 002 by RS485, then the address of the dome is 002. And this address is
power off memory.But if then, we change the HID to 003 by dip switcher, the HID and the SID
are all 003. It means the address of the dome will be same with the HID or SID which we
changed at the last.
- 4
-
II. Setup of the Menu of the Dome Camera
Basic Operation of the Menu
Open the main menu of the setup by the control keyboard or by the matrix via the operation “Call
No. 64 preset position or No.95 preset position”. Besides that, continuously test No.1 preset
position twice in 4 seconds, you can also open the menu; Through setting No.64 or No.95 preset
position in order to close the munu.
When the menu is displayed on the screen, operate “TILT UP”, “TILT DOWN” to move the
cursor to the option to be set, operate “PAN LEFT”, “PAN RIGHT” to modify the content or the
order to enter this option.
All setups on the menu couldn’t be lost even power failure happens.
2.1 MAIN MENU
SYSTEM SETUP: enter the submenu of the SYSTEM SETUP.
MAIN MENU
DISPLAY SETUP: enter the submenu of the DISPLAY SETUP, to
setup the ID DISPLAY, PRESET LABEL and so on.
CAMERA SETUP: enter the submenu of the camera common
parameter setup.
1.<SYSTEM SETUP>
2.<DISPLAY SETUP>
3.<CAMERA SETUP>
4.<MOTION SETUP>
5.<PRIVACY MASK>
6.<ADVANCE SETUP>
7.SYSTEM RESET
8.EXIT
MOTION SETUP: enter the submenu of the dome enhancement functions.
PRIVACY MASK: enter the submenu of the camera PRIVACY MASK setup.
ADVANCE SETUP: enter the submenu of the ADVANCE SETUP.
SYSTEM RESET: to reset the dome camera.The dome camera will self test after the resetting,
and some settings of the dome will be restored: camera auto flip – ON, proportional panning
speed – ON, address display – ON, angle display – ON, display position – top of the screen,
dome title display – OFF, digital zoom – OFF, BLC – OFF, home
SYSTEM SETUP
function – OFF, fan – AUTO, temperature display – OFF.
EXIT：exit from the Main menu.
1.SYSTEM INFORMATION
2.AUTO FLIP OFF
3.PROP PAN SPD OFF
4.RESERVED N/A
5.<ALARM SETUP>
6.RETURN
2.2 SYSTEM SETUP
SYSTEM INFORMATION: enter the submenu of the SYSTEM
INFORMATION.
AUTO FLIP: to ON/OFF the dome camera auto flip function.
SYSTEM INFORMATION
CAMERA SN:000000
CAMERA ID :001
PROTOCOL :P003
BAUD RATE :2400BPS
MODEL :S100P
VERSION :1.00
PROP PAN SPD: to ON/OFF the dome camera proportional panning speed function.
- 5
-
RESERVED: Blank.
ALARM SETUP: enter the submenu of the Alarm setup.
ALARM NO: to select the alarm number, from 1 to 4.
ACTION: to select the action of the dome camera after the alarm,
the action could be 1-50 preset positions, the 1st cruising track, the
SYSTEM SETUP
1.SYSTEM INFORMATION
2.AUTO FLIP OFF
3.PROP PAN SPD OFF
4.RESERVED N/A
5.<ALARM SETUP>
6.RETURN
1st pattern and the 1st scanning line. And the dome camera will go
back to the action before the alarm, after the alarm has been
canceled.
ALARM: to ON/OFF the each numbered alarm.
RETURN: return to the previous menu.
2.3 DISPLAY SETUP: enter the submenu of the DISPLAY SETUP.
CAMERA ID: enter the submenu of the camera ID (address).
DISPLAY: to ON/OFF the display of the camera ID on the screen.
POSITION: to select the display position of the camera ID on the
four corners of the screen.
RETURN: return to the previous menu.
ANGLE DISPLAY: enter the submenu of the ANGLE
DISPLAY.
DISPLAY: to ON/OFF the angle display on the screen.
POSITION: to select the display position of the camera angle on the
top or lower of the screen.
ALARM SETUP
1.ALARM NO: 001
2.ACTION: 001
3.ALARM ON
4.RETURN
DISPLAY SETUP
1.<CAMERA ID>
2.<ANGLE DISPLAY>
3.<PRESET LABEL>
4.<DOME LABEL>
5.RETURN
CAMERA ID
1.DISPLAY : ON
2.POSITION: TOP-R
3.RETUTN
DISPLAY SETUP
1.<CAMERA ID>
2.<ANGLE DISPLAY>
3.<PRESET LABEL>
4.<DOME LABEL>
5.RETURN
ANGLE DISPLAY
1.DISPLAY : ON
2.POSITION : TOP
3.RETUTN
RETURN: return to the previous menu.
PRESET LABEL: enter the submenu of the PRESET LABEL
display.
DISPLAY: to ON/OFF the display of the PRESET LABEL on the
screen.
DISPLAY SETUP
1.<CAMERA ID>
2.<ANGLE DISPLAY>
3.<PRESET LABEL>
4.<DOME LABEL>
5.RETURN
PRESET LABEL
1.DISPLAY : ON
2.POSITION : TOP
3.RETUTN
POSITION: to select the display position of the PRESET LABEL
on the top or lower of the screen.
RETURN: return to the previous menu.
DOME LABEL: enter the submenu of the DOME LABEL.
- 6
DISPLAY SETUP
1.<CAMERA ID>
2.<ANGLE DISPLAY>
3.<PRESET LABEL>
4.<DOME LABEL>
5.RETURN
DOM LABEL
1.DISPLAY : ON
2.POSITION: TOP
3.RETUTN
-
DISPLAY: to ON/OFF the display of the DOME LABEL on the screen.
POSITION: to select the display position of the DOME LABEL on the top or lower of the
screen.
RETURN: return to the previous menu
2.4 CAMERA SETUP: enter the submenu of the CAMERA SETUP, and if the camera module
do not support this function, this item will be blank.
D-ZOOM: to ON/OFF the digital zoom of the camera.
DISPLAY: to ON/OFF the display of the camera information.
FOCUS MODE: to select the FOCUS MODE of the camera: auto iris, auto focus, auto iris &
focus or all manual.
ICR: to select the ICR mode of the camera: auto, day mode or night mode.
BLC: to ON/OFF the back light compensation function.
RESERVED: to ON/OFF the reserved function of the camera. (some cameras do not have this
function.)
SLOW SHUTTER: to ON/OFF the slow shutter function (only
available for SONY camera module.).
WB/AE SETUP: enter the submenu of the WB/AE SETUP of the
camera.
AE MODE: to select the exposure mode of the camera: AUTO /
MANU / SHUTTER.
SHUTTER: to adjust the shutter speed, when the AE MODE is
SHUTTER.
WB MODE: to select the WHITE BALANCE mode of the camera:
AUTO / INDOOR / OUTDOOR / ONEPUSH / ATW / MANUAL.
R GAIN: to adjust the RED GAIN, when the WB MODE is MANUAL.
B GAIN: to adjust the BLUE GAIN, when the WB MODE is MANUAL.
WDR MODE: to ON/OFF the WDR mode.
EXPCOMP SETUP: enter the submenu of the EXPOSURE
COMPENSATION setup.
CAMERA SETU
1.
D-ZOOM OFF
2.DISPLAY OFF
3.FOCUS MODE: MANUAL
4.ICR AUTO
5.BLC ON
6.RESERVED N/A
7.SLOW SHUTTER ON
8.<WB/AE SETUP>
9.RETURN
WB/AE SETUP
1.AE MODE: ATUO
SHUTTER: N/A
2.WB MODE: AUTO
R GAIN N/A
B GAIN N/A
3.WDR MODE ON
4.<EXPCOMP SETUP>
5.RETURN
EXPCOMP SETUP
1.EXPCOMP: ON
2.AMOUNT: -7
3.RETURN
P
EXPCOMP: to ON/OFF the EXPOSURE COMPENSATION of the camera.
- 7
-
AMOUNT: to select the value of the EXPOSURE COMPENSATION: -7～+7.
RETURN: return to the previous menu.
2.5 MOTION SETUP: enter the submenu of the dome enhancement functions.
PRESETS: enter the submenu to edit the label of the PRESETS.
PRESET NO: to select the preset number, from 1 to 128.
Pic.freeze: PIC.FREEZE setting ON/OFF.(Only some series of camera
support the setting of pic.freeze).
EDIT LABEL: to edit the label of the presets, then the screen will
display the figure as the right. The first line means it is the No. 1 preset,
and the second line is just show “NO LABEL” at the beginning. Now
we can use the joystick or the direction keys to modify the label, turn
left/right to move the cursor, and up/down to change the character, the
press “CLOSE” to save and quit the editing status. It is maximum 10
characters in the label, the characters could be 0～9, A～Z, blank and
some special characters: “
；：〈
=
〉？，
@\+、-./ ］”.
CLR LABAL: to clear the label of the preset.
RETURN: return to the previous menu.
MOTION SETUP
1.< PRESETS >
2.
＜＜＜＜
AUTO SCAN
＜＜＜＜
3.
PATROLS
4.
＜＜＜＜
PATTERNS
5.
＜＜＜＜
CLEAR
6
. EDIT DOME LABEL
7
. RETURN
＞＞＞＞
＞＞＞＞
＞＞＞＞
＞＞＞＞
PRESETS
1. PRESET NO 01
2. PIC.FREEZE:ON
3. EDIT LABEL
5. CLR LABEL
6. RETURN
PRESET NO. : 001
LABEL: NO LABEL
MOTION SETUP
1.< PRESETS
2.
＜＜＜＜
AUTO SCAN
＜＜＜＜
3.
PATROLS
4.
＜＜＜＜
PATTERNS
CLEAR
5.
＜＜＜＜
EDIT DOME LABEL
6.
7.
RETURN
>
＞＞＞＞
＞＞＞＞
＞＞＞＞
＞＞＞＞
AUTO SCAN: enter the submenu of the AUTO SCAN.
SCAN NO: to select the number of the line scanning: 1～3.
SPEED: the select the level of scanning speed to each line: 1～7.
SET START LIMIT: to set the start point of the scanning line by
joystick or direction keys, then press “CLOSE” to save and return.
SET END LIMIT: to set the end point of the scanning line by joystick or
direction keys, then press “CLOSE” to save and return.
RUN SCAN: to run the scanning line, and if the start point and the end
point are the same one, the dome will scan for 360°. Press “CLOSE” to
quit.
CLEAR SCAN: to clear the scanning line we selected.
RETURN: return to the previous menu.
- 8
AUTO SCAN
1. SCAN NO : 001
2. SPEED
3. SET START LIMIT
4. SET END LIMIT
5. RUN SCAN
6. CLEAR SCAN
7. RETURN
:
001
MOTION SETUP
1.< PRESETS
2.
＜＜＜＜
AUTO SCAN
3.
＜＜＜＜
PATROLS
4.
＜＜＜＜
PATTERNS
5.
＜＜＜＜
CLEAR
6.
EDIT DOME LABEL
7.
RETURN
1. PATROL NO : 001
2. EDIT PATROL
3. RUN PATROL
4. CLEAR PATROL
5. RETURN
>
＞＞＞＞
＞＞＞＞
＞＞＞＞
＞＞＞＞
PATROLS
-
PATROL: enter the submenu of the cruising tracks （PATROL）.
PATROL NO: to select the number of the PATROL.
EDIT PATROL: to edit the patrol, the screen will be display as the following figure:
We can use the joystick or the direction keys to modify the label, turn left/right to move the
cursor, and up/down to change the character, the press “CLOSE” to save and quit the editing
status. The PATROL will follow the number 1~16. We can select the preset number and stay
time for each 1~16 number, and if we blank one number, the patrol will skip that number.
RUN PATROL: to run the PATROL, then press “CLOSE” to quit.
CLEAR PATROL: to clear the PATROL we selected.
RETURN: return to the previous menu.
PATTERNS: enter the submenu of the PATTERNS.
PATTERN NO: to select the number of the PATTERN: 1～3.
RECORD PATTERN: enter this item to start the recording of the
pattern, then use joystick or direction keys to move the camera as the
MOTION SETUP
1.< PRESETS
2.
＜＜＜＜
AUTO SCAN
3.
＜＜＜＜
PATROLS
4.
＜＜＜＜
PATTERNS
5.
＜＜＜＜
CLEAR
EDIT DOME LABEL
6.
7.
RETURN
>
＞＞＞＞
＞＞＞＞
＞＞＞＞
＞＞＞＞
PATTERNS
1.PATTERN NO. 001
2.PECORD PATTERN
3.RUN PATTERN
4.CLENR PATTERN
5.RETURN
pattern we want, then press “CLOSE” to quit.
RUN PATTERN: to run the PATTERN, then the controlling of the joystick or direction keys
will stop the PATTERN.
CLEAR PATTERN: to clear the PATTERN we selected.
RETURN: return to the previous menu.
CLEAR: enter the submenu of the CLEAR.
MOTION SETUP
1.< PRESETS
2.
＜＜＜＜
AUTO SCAN
＜＜＜＜
3.
PATROLS
4.
＜＜＜＜
PATTERNS
5.
CLEAR
＜＜＜＜
6.
EDIT DOME LABEL
7.
RETURN
>
＞＞＞＞
＞＞＞＞
＞＞＞＞
＞＞＞＞
CLEAR ALL PRE LABEL: to clear all the PRESET LABELS.
CLEAR ALL SCAN: to clear all the PRESET LABELS.
CLEAR ALL PATROLS: to clear all the PATROLS.
- 9
CLEAR
1. CLEAR ALL PRELABEL
2. CLEAR ALL SCAN
3. CLEAR ALL PATROLS
4. CLEAR ALL PATTERNS
5. RETURN
CLEAR ALL PATTERNS: to clear all the PATTERNS.
RETURN: return to the previous menu.
EDIT DOME LABEL: to edit the label of the dome. We can use the joystick or the direction
keys to modify the label, turn left/right to move the cursor, and up/down to change the character,
the press “CLOSE” to save and quit the editing status. It is maximum 10 characters in the label,
the characters could be 0～9, A～Z, blank and some special characters: “
；：〈
=
〉？，
@\+
、
-./ ］”.
RETURN: return to the previous menu.
2.6 PRIVACY MASK: enter the submenu of the PRIVACY MASK, and if the camera module
do not support this function, this item will be blank.
PRIVACY MASK: to select the number of the PRIVACY MASK, maybe different amount for
different camera module.
MASK SHADE: to select the mask color of the camera: BLACK,
WHITE or GRAY. Maybe different color collections for different
PRIVACY MASK
1.PRIVACY MASK 01
2.MASK SHADE WHITE
3.DISPLAY ON
4.EDIT MASK
5.RETURN
camera module.
DISPLAY: to ON/OFF the display of the MASK.
EDIT MASK: to edit the MASK area (this area must be a rectangle.). To use the joystick and the
direction keys to move the cursor, then press “OPEN” to select the top left corner and the lower
right corner of the rectangle to define the MASK area.
RETURN: return to the previous menu.
2.7 ADVANCE SETUP: enter the submenu of the ADVANCE SETUP.
HOME SETUP: enter the submenu of the AUTO HOME.
AUTO HOME: to ON/OFF the AUTO HOME function, it means the
dome camera will run the HOME ACTION, if it does not have
commands to follow in the PARK TIME.
HOME ACTION: to select the dome action when the dome run AUTO
HOME function. This action could be PRESET No.1 ~ 50, 1st PATROL,
1st SCAN LINE, 1st PATTERN or the status before the manual
operation.
- 10 -
ADVANCE SETUP
1. < HOME SETUP >
＜＜＜＜
2.
PASSWORD
＜＜＜＜
3.
CAM ID SETUP
＜＜＜＜
4.
FAN CONTROL
5. < >
RESERVED
6.
<MORE >
RETURN
7.
HOME SETUP
1. AUTO HOME : OFF
2. HOME ACTION : 01
3. PAPK TIME :
4.
PWR RESUME : ON
5. RETURN
＞＞＞＞
＞＞＞＞
＞＞＞＞
04 MIN
-
PARK TIME: to set the PARK TIME of the AUTO HOME, from 1 – 99 minutes. The PARK
TIME means the blank time of the dome camera without any commands.
PWR RESUME: to ON/OFF the function of the POWER RESUME, if we ON it, the dome
camera will follow the actions what it was doing before the power fails.
RETURN: return to the previous menu.
PASSWORD: enter the submenu of the PASSWORD.
PASSWORD: to ON/OFF the PASSWORD.
ADVANCE SETUP
1.< HOME SETUP>
＜＜＜＜
2.
PASSWORD
3.
＜＜＜＜
CAM ID SETUP
＜＜＜＜
4.
FAN CONTROL
5. < >
RESERVED
MORE
6.<
7.
RETURN
＞＞＞＞
>
＞＞＞＞
＞＞＞＞
MODIFY KEY: to input the old password first, then enter the new
password, the original password is 111111.
COMFIRM KEY: to enter the new password again to confirm.
RETURN: return to the previous menu.
PASS WORD
1 . PASSWORD : OFF
2. MODIFY KEY :
3 .
CONFIRM KEY:
4 .
RETURN
*******
*******
CAM ID SETUP: enter the submenu of the CAMERA ID SETUP. (CAMERA ID =
CAMERA ADDRESS).
CAMERA S/N: to display the camera serial number.
INPUT S/N: to input the camera serial number as the previous item
ADVANCE SETUP
1.< HOME SETUP>
＜＜＜＜
2.
PASSWORD
＜＜＜＜
3.
CAM ID SETUP
4.
＜＜＜＜
FAN CONTROL
5. < >
RESERVED
MORE
6.<
7.
RETURN
＞＞＞＞
>
＞＞＞＞
＞＞＞＞
by joystick or the direction keys, left/right to move the cursor,
up/down to change the character. Then press “CLOSE” to quit the
editing status.
OLD ID: to display the old ID of the dome camera.
CAM ID SETUP
1. CAMERA S / N: 2800000
2. INPUT S / N
3 . OLD ID
4 . NEW ID
5. SAVE & RETURN
6 . CANCEL & RETURN
:
0000000
:
001
:
001
NEW ID: to input new ID of the dome camera, before this, we have
to input the right serial number.
SAVE & RETURN: to save the new ID then return to the previous
menu.
ADVANCE SETUP
1.< HOME SETUP>
＜＜＜＜
2.
PASSWORD
＜＜＜＜
3.
CAM ID SETUP
4.
＜＜＜＜
FAN CONTROL
5. < >
RESERVED
MORE
6. <
7.
RETURN
＞＞＞＞
>
＞＞＞＞
＞＞＞＞
CANCEL & RETURN: to cancel the new ID then return to the
FAN CONTROL
previous menu.
FAN CONTROL: enter the submenu of the FAN CONTROL.
1. FAN AUTO
2. OPEN TEMP
.
3
TEMP
.
RETURN
4
DISPLAY
:
:
40
:
OFF
FAN: to select the FAN’s mode: ON, OFF or AUTO.
OPEN TEMP: to select the start temperature of the FAN, the range is
from 28 to 55, and it was defined on 40.
TEMP DISPLAY: to ON/OFF the display of the temperature.
RETURN: return to the previous menu.
ADVANCE SETUP
1.< HOME SETUP>
＜＜＜＜
2.
PASSWORD
＜＜＜＜
3.
CAM ID SETUP
＜＜＜＜
4.
FAN CONTROL
5. < >
RESERVED
MORE
6.<
7.
RETURN
＞＞＞＞
>
＞＞＞＞
＞＞＞＞
MORE: to go to the next page of this menu.
- 11
ADVANCE SETUP 2
:
LANGUAGE
1.
SET NORTH
2.
.
SHORTCUT
3
.
PAN SPEED
.
PREVIOUS
5
ENGLISH
OFF
:
:
150
:4
LANGUAGE: to select the language of this dome camera: ENGLISH
or CHINESE.
SET NORTH: to set the NORTH direction. The dome camera will define “NORTH” to the
direction which the camera is facing. And then the relative orientations (EAST, SOUTH,
WEST and so on, amount 8 orientations.) will be display on the screen.
SHORTCUT: to ON/OFF the SHORTCUT commands.
PAN SPEED: to select the panning speed: 100°
/s,
150°
PREVIOUS: to go to the previous page of this menu.
RETURN: return to the previous menu.
/s,
200°
/s,
250°
/s,
300°
/s.
- 12 -
III Setup of the Dome Camera
3.1 Connection of the System
3.2 The Figures of ID and protocol dip switcher.
Figure1
10-bit dip switcher: DIP1～DIP9 are for the ID, DIP10 is a terminal resistor.
6-bit dip switcher: DIP1-DIP4 are for the protocol selection, and the DIP5 & DIP6 are for the baud
rate.
- 13 -
3.3 Dip Switch
The code sheet:
Dome
Address
DIP-1 DIP-2 DIP-3 DIP-4 DIP-5 DIP-6 DIP-7 DIP-8 DIP-9 DIP-10
Status
1 ON OFF OFF OFF OFF OFF OFF OFF OFF OFF
2 OFF ON OFF OFF OFF OFF OFF OFF OFF OFF
3 ON ON OFF OFF OFF OFF OFF OFF OFF OFF
4 OFF OFF ON OFF OFF OFF OFF OFF OFF OFF
5 ON OFF ON OFF OFF OFF OFF OFF OFF OFF
6 OFF ON ON OFF OFF OFF OFF OFF OFF OFF
7 ON ON ON OFF OFF OFF OFF OFF OFF OFF
8 OFF OFF OFF ON OFF OFF OFF OFF OFF OFF
9 ON OFF OFF ON OFF OFF OFF OFF OFF OFF
10 OFF ON OFF ON OFF OFF OFF OFF OFF OFF
11 ON ON OFF ON OFF OFF OFF OFF OFF OFF
12 OFF OFF ON ON OFF OFF OFF OFF OFF OFF
13 ON OFF ON ON OFF OFF OFF OFF OFF OFF
14 OFF ON ON ON OFF OFF OFF OFF OFF OFF
15 ON ON ON ON OFF OFF OFF OFF OFF OFF
16 OFF OFF OFF OFF ON OFF OFF OFF OFF OFF
17 ON OFF OFF OFF ON OFF OFF OFF OFF OFF
18 OFF ON OFF OFF ON OFF OFF OFF OFF OFF
… … … … … … … … … … …
511 ON ON ON ON ON ON ON ON ON OFF
For example:
O
N
1 2 3 4 5 6 7 8 9 10
Speed Dome Addr ess=1
O
N
1 2 3 4 5 6 7 8 9 10
Speed Dome Addr ess=4
Table
O
N
1 2 3 4 5 6 7 8 9 10
Speed Dome Addr ess=2
O
N
1 2 3 4 5 6 7 8 9 10
Speed Dome Addr ess=18
O
N
1 2 3 4 5 6 7 8 9 10
Speed Dome Addr ess=3
O
N
1 2 3 4 5 6 7 8 9 10
Speed Dome Addr ess=511
- 14 -
3.4 Protocol and the Default Baud Rate
The SW2 is used to set the protocol of communication and the baud rate used by the dome
camera. DIP-4 to DIP-1 of SW2 is used to select protocols and 16 different protocols can be selected
in maximum. Following table shows states of coding switches of protocols selected by the dome
camera.
Protocols
DIP status
Normal Baud Rate
DIP-1 DIP-2 DIP-3 DIP-4 DIP-5 DIP-6
B01 ON OFF OFF OFF OFF ON
SAMSUNG-1 ON OFF OFF OFF OFF ON
Santachi OFF ON OFF OFF OFF ON
PELCO-P/D ON ON OFF OFF OFF OFF
PELCO-MK OFF OFF ON OFF OFF OFF
PANASONIC ON OFF ON OFF OFF ON
Longcomity OFF ON ON OFF OFF ON
HUNDA600 ON ON ON OFF OFF ON
LILIN OFF OFF OFF ON OFF ON
VICON ON OFF OFF ON ON OFF
MOLYNX OFF ON OFF ON OFF ON
KALATEL ON ON OFF ON ON OFF
VCL OFF OFF ON ON OFF ON
SAMSUNG-2 ON OFF ON ON OFF ON
ALEC OFF ON ON ON OFF ON
Ultrak ON ON ON ON OFF ON
Table 2
SAMSUNG-1 is old SAMSUNG protocol,SAMSUNG-2 is new updated SAMSUNG protocol.
- 15 -
3.5 Setup of the Baud Rate
As shown in the Figure, SW2 is used to set the protocol of communication and the baud rate used
by the dome camera. DIP-6 and DIP-5 of SW2 are used to select the baud rate of communication and
4 different baud rates can be selected in maximum. If the controller adopts non-standard baud rate,
you can adjust it to be identical with that of the main machine as per the following table.
Baud Rate of Communication DIP-1 DIP-2 DIP-3 DIP-4
2400 bps OFF OFF
4800 bps ON OFF
9600 bps OFF ON
19200 bps ON ON
Setup of Baud Rate
DIP-5 DIP-6
3.6 Selection of the Terminal Resistor
As shown in the Figure, sw1is the select switch of the 120 Ω terminal resistor on the bus
RS485, on which only one terminal resistor of the dome camera at the farthest end can be
connected, while the terminal resistors of other devices should be opened.
3.7 Special Control (the SHORTCUT item must be ON in the menu)
NO
1
64
65
66
67
68
69
70
Set Preset
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Tow Preset Open the menu
Call Preset
Open the menu
Run patrol 1
Run patrol 2
Run scan 1
Run scan 2
Run pattern 1
Run pattern 2
- 16 -
Atmospheric
Power supply
DC12V/2.5A
Ambient
ⅣⅣⅣⅣ
.
Description of Installation
4.1 Safety Measure
4.1.1 The requirement of the installation and service personnel.
With the qualifications of the CCTV system installation, high-altitude operation and other related
certifications.
With the basic knowledge and operation skill of the low voltage wiring and Low voltage
electronic circuit wiring.
With the ability to spell over this manual.
4.1.2 The requirement of the lifting appliance.
To be suitable for the installation place and dome installation.
With the good safety capability.
4.2 Warning
To prohibit to install and use this product near the flammable and explosive materials.
Please abide the national and regional electric safety regulations.
To be sure the power supplies have been disconnected during the installing of the products.
12VDC is the standard input voltage of this product, do not take the higher voltage to connect
with this product.
Do not install this product in the place where the ambient is too severe to use this product.
4.3 Ambient requirement
Indoor dome camera:
Ambient
0～+40
Temperature
Humidity 10-75% (without agglomeration)
86～106KPa
pressure
Outdoor dome camera:
-35
℃
～
+55℃
Temperature
Humidity 10-75% (without agglomeration)
Atmospheric
86～106KPa
pressure
Power supply DC12V/2.5A
- 17 -
4.4 Preparation
4.4.1 Basic requirement
Please abide the latest electric, fireproofing and other related regulations.
Please check if all the accessories are complete, and if this product is the same with your
requirement. Please contact with the supplier if not.
Please install and use this product under the right ambient.
4.4.2 Please check there are enough room and intensity to install this product.
4.4.3 Please check the intensity of the structure.
4.4.4 To setup the dip switcher.
To setup the dip switcher as the right protocol, baud rate and dome ID. ( refer to the setup of
the dome.)
4.4.5 The self testing of the dome
Please make the self testing of the product first before we install this product, if this product can
not complete the self testing, please stop the installation and contact with the supplier.
4.4.6 Please keep all the package materials.
Please keep all the package materials, and if this product need to be sent back, it need to be packed
safety.
4.5 Brief of the Installation
There are two types of the SPEED DOME CAMERA as the installation ambient: Outdoor
speed dome camera and Indoor speed dome camera. And there are three types of the SPEED
DOME CAMERA as the installation manner: Outdoor wall installation, indoor wall installation and
ceiling installation. As follows:
a) Ceiling installation
Figure 2 Figure 3
- 18 -
b) Wall installation
Figure 4 Figure 5
c) Outdoor wall Installation
Figure 6 Figure 7
4.6 Installing of the dome
1) Steps of installation for ceiling bracket.
a)
Open the packing cartons, take out of the dome and accessories carefully.
b)
Drill 3 holes according to the size on the ceiling.（Figure 8）.
c) Fix the dome on the ceiling with screws.（Figure 8）.
d) Take out of the dome, and put three pieces of screws into the fixing hole, rotate it
towards the clockwise direction until it’s tighten.（Figure 9）.
- 19 -
Figure 8 Figure 9
e) Finally fix the camera bottom board and camera connecting board with M3 Screws.
2） Steps of wall installation.
a)
Open the packing cartons, take out of the dome and accessories carefully.
b) Drill holes according to the position of the bracket bottom pedestal, and then fix the
bracket on the wall with 4 pieces of M6 screws.（Figure 10）.
c) Fixing the bracket on the wall with 4 pieces of M6 Screws.（Figure 11）.
Figure 10 Figure 11
d) Taking out of the dome, and put three pieces of screws into the fixing hole, rotate it in
a clockwise direction until it’s tighten.（Figure 12）.
Figure 12
- 20 -
Figure13
e) Finally fix the camera bottom pedestal board and camera connecting board with M3
Screw.
3) Steps of outdoor wall Installation.
a) Unpacking the carton and carefully take out the dome camera and its attachment.
b) Take out of the dome, and put three pieces of fast-fixed screws into the fixing hole,
rotate it towards the clockwise direction until it’s tighten. Finally fix the camera
bottom pedestal board and camera connecting board with M3 Screw（Figure13）.
d） Drill some holes on the wall according to the bottom fixed holes(Figure7)，then fix the
bracket on the wall（Figure14）.
e）Take out system control wires ,video wires, the power wires from the bracket
（
Figure15）.
f) Fix the dome on the wall with screws（Figure16）.
Figure 14 Figure15
- 21 -
Figure16
4.7 The taking aparts ways for the black cover
1) The taking aparts ways as the following steps：
a) Rotate the vitreous cover counterclockwise and take out it（As Figure 17shows）.
b)
Please firm the ball machine with your hands, two thumbs place the black cover hole separately, then
makes an effort to one side to cause the black cover internal bayonet socket slightly to be separated
from square shape installment hole of the camera mounting panel's, then take out the black cover
Figure 18shows）.
：：：：
（
As
Figure 17
Figure 18
2）The installing ways for the black cover：
a)
First please insert the black cover internal bayonet socket's A part to the square shape hole of the camera
mounting panel's, then makes an effort with the similar method to install slightly of the other side of the
black cover bayonet socket
（
As Figure 19 shows）.
b) Rotate the vitreous cover clockwise and mount it（As Figure 20 shows）.
- 22 -
.
Figure 19 Figure 20
4.8 The installing ways for the camera
1) The installing way of
a)
Take out
panel's camera's for 9 core flat wire, then make it that Camera on hole B alignment camera mounting
panel hole A ,and fix it with M2X3 screw
MINTRON
MINTRON camera module
camera , pass through square shape installment hole C of the camera mounting
：
（
As Figure 21 shows）.
b)
Take out MINTRON camera’s junction board, insert the camera flat wire to the 9 core camera
plug, then insert the plug to 7 core plugs.
c) Finally, please fix the hole of camera Junction panel according to the hole D and hole E
with two pcs M2X5 screws（As Figure 23 shows
Figur 21
（
As Figure 2 shows）.
- 23 -
）
Figure 22 Figure 23
2) The Installing way of Samsung camera ：
a)
Take out Samsung camera’s junction board, make it that Camera on hole B alignment camera mounting
panel hole A ,then take out camera junction panel ,and insert the camera flat wire to the 24 core camera
plug, then insert the plug to 7 core plugs.
（
As Figure 24 shows）.
Figure 24
b) please fix the hole of camera Junction panel according to the hole A and hole B with three pcs
M2X5 screws, finally please fix the camera flat wire to the camera with black Sticks strip, so as it
could avoid the bottom of camera touching of the PCB board.（As Figure 25 shows）.
black Sticks strip
Figure 25
- 24 -
3) The Installing way of Sony CNB.12X camera：
a) Take out Sony camera
take out Sony camera junction panel ,and insert the camera flat wire to the 9 core camera plug, then insert
the plug to 7 core plugs.
，
make it that Camera on hole B alignment camera mounting panel hole A ,then
（
As Figure 26 shows）.
Figure 26
b) Please fix the hole of camera Junction panel according to the hole A and hole B with two pcs
M2X5 screws, finally please fix the camera flat wire to the camera with black
could avoid the bottom of camera touching of the PCB board
Figure 27
（
As Figure 27 shows）.
Sticks strip, so as it
- 25 -
4.9 Connect the control cable as Figure 28.
Figure 28
Identifier of the alarm lines as Figure 29:
Figure 29
Notice 1: the signal of the alarm in must be switchable; other signals (such as the voltage
signal) will damage the dome. When the alarm signals come from multi-channel, the dome
will respond them one by one, and the response interval is 2 seconds.
Notice 2: In case there are one or more alarm signals, the dome will never respond the
function: “line scanning”, “tracking” and “self-learning” etc.
Connect the alarm lines as Figure 30.
Figure 30
- 26 -
Appendix I
No action when power
is switched on
Abnormal self-check.
Images with motor
noise
Normal self-check but
no images
Normal self-check but
out of control
.Troubleshooting
Problems Possible Causes Remedies
Power supply fault Replace
Bad connection of the power Correct
Transformer damaged Replace
Mechanical failure Repair
Camera inclined Reinstall
Power supply not enough Replace
Video signal fault Reinstall
Bad connection of the video Press to connect well
Camera damaged Replace
RS485 bus bad connection Check the RS485 connection
Dome ID setup is wrong Reselect
Protocol setup is wrong Reset and Switch ON again
Vague image
Dome camera out of
control
Bad connection of the video Press to connect well
Power supply not enough Replace
Self check error Switch ON again
Bad connection of control Press to connect well
Bad control of matrix Switch ON again
- 27 -
: Cleaning of the transparent cover
Appendix ⅡⅡⅡⅡ
Cleaning the cover for special time so as it is keeping cleaning.
Be cautious when cleaning. Hold the down cover ring only to avoid direct touch to the acrylic
down cover. The acid sweat mark of fingerprint will corrode the coating of down cover and
scratch on down cover will cause vague images.
Use soft dry cloth or the substitute to clean the inner and outer surfaces.
For hard contamination, use neutral detergent. Any cleanser for high grade furniture is applicable.
- 28 -
4800 Bps
1200m
Appendix ⅢⅢⅢⅢ
. RS485 Bus Basic Knowledge
1. Connection and termination resistor
The RS485 standards require a daisy-chain connection between the equipment. There must be
termination resistors with 120Ωimpedance at both ends of the connection .
2. Transmission distances of RS485 Bus
When user selects the 0.56mm (24AWG) twisted pair wires as data transmission cable, the
maximum theoretical transmitting distances are as follows:
Baud Rate Maximum Transmitting Distance
2400 Bps 1800m
9600Bps 800m
3. Connection and termination resistor
The RS485 standards require a daisy-chain connection between the equipment. There must be
termination resistors with 120Ωimpedance at both ends of the connection (refer to Picture 31).
Please refer to Picture 20 for simple connection. “D” should not exceed 7m.
120Ω 120Ω
1# 2# 3# 4# 32#
. . . . .
Figure 31
A+
. . . . .
. . . . .
120Ω
D
Main controller
B-
A+ B-
120Ω
1# 2# 3# 31#
Figure 29
- 29 -
Loading...