COP-USA CD55-H-SDI User Manual

Download

HD-SDI High Speed Dome Camera

Series

USER’S MANUAL

Note:

※Please read the operation manual carefully before installing and using this unit

Warning:

To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. Do not

insert any metallic objects through the bentilation grills or other openings on the equipment.

This symbol indicates

that dangerous voltage

constituting a risk of

electric shock is present

within this unit.

CAUTION: TO REDUCE THE RISK OF

ELECTROIC SHOCK, DO NOT

REMOVE COVER(OR BACK). NO

USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL

Content

Warning .......................................................................................... Error! Bookmark not defined.

Content ........................................................................................... Error! Bookmark not defined.

1.Points for attention ....................................................................... Error! Bookmark not defined.

2.Function Description .................................................................... Error! Bookmark not defined.

3.System Connection ..................................................................................................................... 6

4.Installation ................................................................................................................................... 7

5.Operation Introduction ................................................................. Error! Bookmark not defined.

6.Technicial data ........................................................................................................................... 23

7.Troubleshooting ........................................................................... Error! Bookmark not defined.

Appendix I: Lightning proof and surge signal proof ......................... Error! Bookmark not defined.

Appendix II: The cleaning of clear downdover ................................ Error! Bookmark not defined.

Appendix III: RS485 bus basic knowledge ................................................................................... 26

I. Points for Attention

1. Please read the operation manual carefully before installing and operating the product.

2. The product takes power supply of AC24V. The rated input voltage of the camera is marked on the base or other corresponding place.

3. During the course of transportation, storage and installation, the product should be avoided from incorrect operations such as heavy pressing, strong vibration etc., which can cause damage of product as there are sophisticated optical and electronic devices inside the machine.

Do not attempt to disassemble the camera. In order to prevent electric shock, do

not remove screws or covers. There are no user-serviceable parts inside.

5. Always follow all electrical standards for safety when it is in operation. Adopt the

particular power supply which is provided with the unit. RS-485 and video signal should keep enough distance with high voltage equipments and cables when they are in transmission. Precautions for anti-lightning and anti-surging should be taken if necessary.

6. Do not operate it in case temperature, humidity and power supply are beyond the limited stipulations.

7. Do not let the camera aim at the sun or the object with extreme light whatsoever it is switched on or not. Do not let the

camera aim at or monitor bright and standstill object for a long time.

8. Do not use aggressive detergent to clean the main body of the camera. Wipe dirt with dry cloth. If needed, mild detergent

can be used suitably.

9. Operate the intelligent speed dome camera with great care to avoid shock or vibration. It operate incorrectly, the Speed

Dome could be damaged

10. Be careful to avoid to crash, Never mount the unit on a ceiling that cannot support its weight.

11. If necessary, use a commercial lens cleaning paper to clear the lens windows. Gently wipe the lens window until clean.

II. Functions Description

Integrated speed-variable PAN/TILT

a. Turning 360°horizontally and continuously with unlimited positions and an

adjustable speed from 0 -- 300°/s; turning 0 - 90°vertically with a speed up to 120°/s. b. Running stably at low speed with super lower noise. Pictures have no shaking. c. the location precision up to

d. 6 programmable tracks, 4 scanning tracks,1 pattern track. e. Idle ptorection and power-off memory function.

f. Display orientation,title of speed dome camera,temperature, alarm and other

informations

2. High Intelligent Degree

a. 255 preset positions can be preset with powerless memory; b. The camera can scan horizontally between two points and scan speed can be

modified. The positions of linear scan are optional and the dome camera can scan the range larger or smaller than 180° between any two points with adjustable speed;

c. Automatic speed matching function

d. Built-in PELCO-D、PELCO-P protocol, baud rate from 2400bps to 19200bps

±0.1°.

3. Functions of the Camera

a. Description of the Focus Control Mode: the user can adjust the focus of the

camera manually. b. Description of Backlight Compensation: when the object to be shot is dark

and looks dim, the user can open the backlight compensation according to

actual need. c. Description of White Balance: when the image has color distort on the screen,

the user can set different modes by orders. There are 6modes for options: 

Indoor Mode  Outdoor Mode  Touch Mode Automatic Trace of

White Balance ATW  Manual WB-MAN  Automatic Mode. d. Description of ZOOM Control: user can “pull near” or “push far” the lens

according to actual conditions e. Electron shutter: it is 1/50 sec after the camera electrified, and it will display 50

on the monitor. f. AE Mode: setup of Manual/Automatic. g. Low illumination set: It is used only when the external brightness is extremely

low. Normally the camera works on the automatic state. In case the external

brightness is lower than 1Lux, the camera can be switch to the Zero

Illuminance state automatically and icon appears on the screen. You can

also set the Zero Illuminance state manually

III. System connection

Fig 1

IV.Installation

1.Conect description

1.1 4 kinds of bracket installation for outdoor speed dome：wall mount, cornet

mount, ceilling mount, pole mount.

1.1.1 Wall mount Check the wall and make sure it’s firm. The bearing weight is more than 8 times of the

speed dome weight.

a. Label installation position

c. Assemble the speed dome

b. Install the bracket

d. Fix the speed dome

e. Connection of cables

1.1.2 Corner mount Check the wall and make sure it’s firm. The bearing weight is more than 8 times of the

speed dome weight.

f. Label installation position

g. Install the bracket

a. Install the base

Make the power cable, RS485 cable and

video cable through the hole of base

b. The same way of wall mount

installation

1.1.3 Pole mount

The diameter of pillar is 130-150mm( 5.12”~6)

a. Install the base

b. Install the bracket c. The same way of wall mount

installation

1.1.4 Ceilling mount

If the ceiling is too low, we can install the speed dome on the base directly.

a. Label installation position

c. Installation the base

팔

d. Install the bracket

Note:if outdoor, please use silicone gel and

rubber belt

Make the cable through the hole and fix the

base on the ceilling.

Note: if install outdoor, please coat silicone

gel on the base.

d. Install the dome housing

Note, if outdoor, please use waterproof tapes,

if the ceilling is too low, we may install on the

base directly.

e. Connection of cables

According to the connection identifier

1.2. Installation for indoor speed dome.

1.2.1 Carefully read the operation manual

and the point for attention.

1.2.2 Carefully set the communication code,

baud rate and address of the high speed

dome camera and make confirmation they

are correct.

구

1.2.3 Take out the plug of the dome camera

and connect external power supply, RS485

and VF wires as per marks on the plug. Take

care that the power supply of the spherical

camera and adopt the particular power

supply which is provided with the dome

camera.

1.2.4 Take out the mounting base from the

spherical camera, thread the connecting wire

from behind through the central hole of the

base. Fix the base by three screws on the

ceiling as per the drawing, and connect the

wire with the ball. Aim the latch in the ball

with the notch on the base as per the drawing,

and mount the ball upward to the position

and turn it clockwise until the spring sheet on

the base takes effect. In case the wire could

not come out from behind the ceiling, you can

open a hole on the edge of the casing for

running of the wire.

이

2.Product size

Fig 4.1

3.Connection identifier

Fig 4.2

V. Operation Introduction

1. Basic Operation of the Menu

1.1 Open the main menu of the setup by the keyboard or the matrix via the

operation “Call No. 64 preset position

1.2

When the menu is displayed on the screen, operate “TILT UP”, “TILT

DOWN” to move the cursor to the option to be set, operate “PAN LEFT”,

“PAN RIGHT” to modify the content or the order to enter this option.

1.3

All setups on the menu couldn’t be lost even power failure

2. Setup of the Menu

1.1 MAIN MENU

1.1.1 SYSTEM SETUP.

1.1.2 DISPLAY SETUP: to enter the submenu of display of the screen by

which ID display, title display of preset point and display of

camera screen can be set.

1.1.3 CAMERA SETUP: to enter the submenu of setup of normal

data of camera.

1.1.4 MOTTON SETUP: to enter the setup of enhanced function of

MAINMENU

1.<SYSTEM SETUP>

2.<DISPLAY SETUP>

3.<CAMERA SETUP>

4.<MOTION SETUP>

5.<PRIVACY MSK>

6.<ADVANCE SETUP>

7.SYSTEM RESET

8.EXIT

dome camera.

1.1.5 PRIVACY MASK: to enter the submenu of the camera privacy function

setting.

1.1.6 ADVANCE SETUP.

1.1.7 SYSTEM RESET: to reset the system. The dome will make

self-checking function after it carries out reset function, the station for

the dome's reset is ： AUTO FLIP -ON/PTZ SPD RATE-ON/ ID

DISPLAY-ON/ANGLE DISPLAY-OFF/ DOME LABEL DISPLAY-OFF/

D-ZOOM-OFF/ PT INTERLOCK –AF AUTO/BLC-OFF/ AUTO HOME

–OFF/ PARK TIME -4MIN/FAN-AUTO/ TIMP DISPAY-OFF。

1.1.8 EXIT: to quit the main menu.

1.2 SYSTEM SETUP

1.2.1 SYSTEM INFORMATION: to display the system information.

1.2.2 AUTO FLIP: to ON/OFF the dome 180°auto flip.

1.2.3 PROP PAN SPD: to ON/OFF the proportional pan function.

1.2.4 RESERVED：This function setting also kept for this products.

1.2.5 ALARM SETUP:

1.2.5.1 ALARM NO: N/A

1.2.5.2 ACTION: N/A

1.2.5.3 ALARM: N/A

1.2.5.4 RETURN: to return to the SYSTEM SETUP menu.

1.2.6 RETURN: to return to the main menu.

1.3 DISPLAY SETUP

SYSTEM SETUP

1.SYSTEM INFORMAT I ON

2.AUTO FLIP: ON

3.PROP PAN SPD: ON

4.RESERVED: N/A

5.<ALARM SETUP>

6.RETURN

SYSTEM SETUP

1.SYSTEM INFORMATION

2.AUTO FLIP: ON

3.PROP PAN SPD: ON

4.RESERVED: N/A

5.<ALARM SETUP>

6.RETURN

1.3.1 CAMERA ID: when it is set at ON, address of dome camera

appears on the screen such as “CAM 001”. The default setting

is ON.

1.3.1.1 DISPLAY: to ON/OFF the dome address.

1.3.1.2 POSITION: to set the position of dome address, there are four

positions to be displayed: TOP-L (top-left corner), TOP-R

(top-right corner), BOTT-R (bottom-right corner) AND

BOTT-L (bottom-left corner).

1.3.1.3 RETURN: to return to the DISPLAY SETUP menu.

1.3.2 ANGLE DISPLAY: to enter the angel display submenu.

1.3.2.1 DISPLAY: to ON/OFF the angle display. ONEPUSH

singly displayed, auto disappeared in 4 seconds.

1.3.2.2 POSITION: to set the display position of the angle:

TOP/BOTTOM.

1.3.2.3 RETURN: to return to the DISPLAY SETUP menu.

1.3.3 PRESET LABEL: to enter the PRESET LABEL submenu.

1.3.3.1 DISPLAY: to ON/OFF the display of the preset label. If it

is ON, the preset label will be displayed on the left of the

monitor when the preset position is setting.

1.3.3.2 POSITION: to set the display position of the preset label:

TOP-at the top of the monitor, BOTTON- at the bottom of

the monitor.

1.3.3.3 RETURN: to return to the DISPLAY SETUP menu.

1.3.4 DOME LABEL: to enter the DOME LABEL submenu.

1.3.4.1 DISPLAY: to ON/OFF the display of the dome label.

1.3.4.2 POSITION: to set the display position of the dome label:

TOP-at the top of the monitor, BOTTON- at the bottom of

the monitor.

1.3.4.3 RETURN: to return to the DISPLAY SETUP menu.

1.3.5 RETURN: to return to MAIN MENU.

1.4 CAMERA SEUP: If setting camera parameter is N/A, it

means the camera can not support this function.

1.4.1 D-ZOOM: to ON/OFF the digital zoom.

1.4.2 DISPLAY: to ON/OFF the display of the camera

information.

1.4.3 FOCUS MODE: NON: iris & focus invariably / A-AUTO:

Auto iris / F-AUTO: Auto focus / AF-AUTO: Auto iris and focus.

1.4.4 ICR: to set the AUTO/DAY/NIGHT situation.

1.4.5 BLC: to ON/OFF the back light compensation.

1.4.6 L-SYNC: to ON/OFF the external synchronization. (Only for some

special cameras.)

1.4.7 SLOW SHUTTER: frame accumulation with two options

Manual/Automatic. When camera screen is opened under automatic

state, ASS displays on screen. (Only sony camera has this function)

1.4.8 WB/AE SETUP.

1.4.8.1 AE MODE: to set the automatic exposure to

MANU/AUTO/SHUTTER mode; SHTTER: it is only

available at the AE MODE is SHUTTER.

1.4.8.2 WB MODE: to set the white balance mode: ATW /

MANUAL / AUTO / INDOOR / OUTDOOR / ONEPUSH;

R GAIN: it is only available for pulsing red at the WB

MODE

Is MANUAL.

B GAIN: it is only available for pulsing blue at the WB

MODE is MANUAL.

1.4.8.3 WDR MODE: to ON/OFF the Wide Dynamic Range mode.

1.4.8.4 EXPCOMP SETUP：exposure-compensation.

1.4.8.5 EXPCOMP: exposure-compensation.

1.4.8.6 AMOUNT:

the value of exposure-compensation:-7 - +7.

1.4.8.7 RETURN: to return to the WB/AE SETUP menu.

1.4.9 RETURN: to return to the MAIN MANU.

1.5 MOTION SETUP

1.5.1 PRESETS: to enter the Preset Position submenu.

1.5.1.1 PRESET NO: to edit the preset number.

1.5.1.2 EDIT LABEL: to edit the preset label. After entering the

edit mode, 1-225 present positions. It displayed on screen

as the pictures: in the picture, “PRESET NO” stands for

NO.1 present position, the topic is “NO LABEL”. Using

PANLEFT/RIGHT can remove the cursor, TILT UP/DOWN

can modify the number, press the “CLOSE”, exit edit mode

and save it. The topics of the present positions includes 10

characters at most, they are 0-9, A-Z, blank and special

characters including 〈 = 〉？，@\+、-./ ］etc. Notes: the

first letter must be from 0-9 or A-Z, in case that, it stands

for canceling the preset position topic. When testing the

preset position, it only display “NO.XXX”, not display the

topic.

1.5.1.3 CLR LABEL: to clear the preset label.

1.5.1.4 RETURN: to return to the PROGRAM SETUP submenu.

1.5.2 AUTO SCAN: to enter the Auto Scanning submenu:

1.5.2.1 SCAN NO: to set the auto scanning number, maximum

is 03.

1.5.2.2 SPEED: to set the scanning speed for each patrol.

1.5.2.3 SET START LIMIT: to set the start position of the

scanning. After the user enter this item, to use the

joystick to move the dome camera and press “CLOSE”

to save the current position.

1.5.2.4 SET END LIMIT: to set the end position of the scanning.

After the user enter this item, to use the joystick to

move the dome camera and press “CLOSE” to save the current

position.

1.5.2.5 RUN SCAN: to run the scanning function, Please set the start and

end position first. And if the start and end position are

the same. The dome camera will scanning for 360°。To

press “CLOSE” to exit.

1.5.2.6 CLEAR SCAN: the clear the setting of the scanning, to

press “CLOSE” to exit.

1.5.2.7 RETURN: to return to the PROGRAM SETUP menu.

1.5.3 PATROLS: to enter the submenu to set the patrols.

1.5.3.1 PATROL NO: to set the patrol number.

1.5.3.2 EDIT PATROL: to set the parameter of the patrol, after enter this item,

the monitor is as following:

Both top and bottom lines display prompt and information of each

patrol is displayed on the middle of the screen. Data of 2 Patrol

points appears on one line. And to press PAN LEFT/RIGHT to

move the cursor, to press TILT UP/DOWN to modify the data, to press

“CLOSE” to save and quit the edit state.

1.5.3.3 RUN PATROL: to run the patrol, press “CLOSE” to exit.

1.5.3.4 CLEAR PATROL: to clear the patrol.

1.5.3.5 RETURN: to return to the PROGRAM SETUP menu.

1.5.4 PATTERNS: to enter the PATTERN setting submenu.

1.5.4.1 PATTERNS: to edit the pattern number. No 1-3 for optional.

1.5.4.2 RECORD PATTERN: to record the pattern, and press

“CLOSE” to exit.

1.5.4.3 RUN PATTERN: to run the pattern, and will quit the menu

automatically, and any move of the joystick will stop this

function.

1.5.4.4 CLEAR PATTERN: to clear the setting of the pattern.

1.5.4.5 RETURN: to return to the superior menu.

1.5.5 CLEAR: to enter the CLEAR submenu.

1.5.5.1 CLEAR ALL PRELABEL: to clear all the preset positions.

1.5.5.2 CLEAR ALL SCAN: to clear all the scanning.

1.5.5.3 CLEAR ALL PATROLS: to clear all the patrols.

1.5.5.4 CLEAR ALL PATTERNS: to clear all the patterns.

1.5.5.5 RETURN: to return to the PREGRAM SETUP menu.

1.5.5.6 EDIT DOME LABEL: To edit the dome label. Set a label for each

dome, the label is make up of 10 characters, and the optional

character is the same as 2.5.1.2.

2.5.7 RETURN: to return to the MAIN MENU.

1.6 PRIVACY MASK:

1.6.1 PRIVACY MASK: to set the privacy number. 1-4 for optional.

(different cameras have different choose)

1.6.2 MASK SHADE: to set the color of the mask area.

1.6.3 DISPLAY: to ON/OFF the privacy function

1.6.4 EDIT MASK: to edit the mask area.

1.6.5 RETURN: to return to Main Menu.

1.7 ADVANCE SETUP:

1.7.1 HOME SETUP: to enter the auto home submenu.

1.7.1.1 AUTO HOME: to set ON to open the AUTO HOME function, it is

mean the dome camera will back to the home position without any

action in the PARK TIME. And set OFF to close this function.

1.7.1.2 HOME ACTION: to set the auto home point. For example:

if the user want to set one scene to be the HOME, just set

the dome camera to this scene, and set it to be the preset

No:3, then open this menu, set the HOME ACTION to be

“3”. And don’t forget to set the AUTO HOME to be ON.

The HOME ACTION could be the preset “1-50”, RESUME,

PATROL 1, SCAN 1, PATT 1. The “1-50” are the preset

number, RESUME is mean to back to the scene before

the manual control, PATROL 1 is the patrol No.1, SCAN 1 is the

scanning No.1 and the PATT 1 is the pattern No.1.

1.7.1.3 PARK TIME: to set the park time of the dome camera, it is mean how

long the dome camera will be back to the HOME. The time from 1-99

minutes.

1.7.1.4 PWR RESUME: to ON/OFF the function, which the dome camera

will be back to the scene before the power off.

1.7.1.5 RETURN: to return to the ADVANCE SETUP Menu.

1.7.2 PASSWORD: to enter the password setting menu. (Initial

pa ssword is 111111.)

1.7.2.1 PASSWORD: to ON/OFF the password protection.

1.7.2.2 MODIFY KEY: to enter the new password.

1.7.2.3 CONFIRM KEY: to enter the new password again for

confirm.

1.7.2.4 RETURN: to return to the ADVANCE SETUP menu.

1.7.3 CAM ID SETUP: to enter the soft ID setting submenu.

1.7.3.1 CAMERA S/N: to display the series number of the dome.

1.7.3.2 INPUT S/N: to input the series number of the dome.

1.7.3.3 OLD ID: to display the old address of the dome.

2.7.3.4 NEW ID: to display the new address of the dome. Input

the series number before inputting the new address.

2.7.3.5 SAVE & RETURN: to save and return to the ADVANCE

SETUP menu.

2.7.3.6 CANCEL & RETURN: to cancel and return to the

ADVANCE SETTING menu.

2.7.4 FAN CONTROL: to enter the fan control setting submenu.

2.7.4.1 FAN: to set the work condition of the fan: ON / OFF /

AUTO.

2.7.4.2 OPEN TEMP: to set the work temperature of the fan

under AUTO condition.

2.7.4.3 Temperature Fahrenheit / Celsius display switch.

2.7.4.4 TEMP DISPLAY: to ON/OFF the display of the temperature.

2.7.4.5 RETURN: to return the ADVANCE SETUP menu.

2.7.5 LANGUAGN: to select the language.

2.7.6 SET NORTH POSITION.

2.8 EXIT: to exit the main menu.

3. Code switch setting

3.1 Code Switch position

Fig 5.1

3.2 Setup of Coding Switch of Dome Camera

As shown in Figure 5.1, SW1 is used to set address of the dome camera

from 1 – 1023. The ID-CODE from DIP-10 to DIP-1 are equivalent to a 10-bit

binary digit. DIP-10 is MSB while DIP-1 is LSB. The state “ON” of each bit

means 1 while “OFF” means 0. Following table shows states of coding

switches of some addresses.

Dome

Address

1 ON OFF OFF OFF OFF OFF OFF OFF OFF

2 OFF ON OFF OFF OFF OFF OFF OFF OFF

3 ON ON OFF OFF OFF OFF OFF OFF OFF

4 OFF OFF ON OFF OFF OFF OFF OFF OFF

5 ON OFF ON OFF OFF OFF OFF OFF OFF

6 OFF ON ON OFF OFF OFF OFF OFF OFF

7 ON ON ON OFF OFF OFF OFF OFF OFF

8 OFF OFF OFF ON OFF OFF OFF OFF OFF

9 ON OFF OFF ON OFF OFF OFF OFF OFF

10 OFF ON OFF ON OFF OFF OFF OFF OFF

11 ON ON OFF ON OFF OFF OFF OFF OFF

12 OFF OFF ON ON OFF OFF OFF OFF OFF

13 ON OFF ON ON OFF OFF OFF OFF OFF

14 OFF ON ON ON OFF OFF OFF OFF OFF

15 ON ON ON ON OFF OFF OFF OFF OFF

16 OFF OFF OFF OFF ON OFF OFF OFF OFF

17 ON OFF OFF OFF ON OFF OFF OFF OFF

18 OFF ON OFF OFF ON OFF OFF OFF OFF

… … … … … … … … … …

512 ON ON ON ON ON ON ON ON ON

DIP-1 DIP-2 DIP-3 DIP-4 DIP-5 DIP-6 DIP-7 DIP-8 DIP-9

ID-CODE Status

Table 1

Eg：

3.3 Setup of the Protocol and the Default Baud Rate

As shown of figure 5.1, J8 set the protocol and baut rate of speed dome. DIP-4to DIP-1

to choose the protocol,DIP-1 to DIP-4 are all OFF means PELCL-D protocol

Protocol

PELCO-D OFF OFF OFF OFF OFF OFF

DIP-1 DIP-2 DIP-3 DIP-4 DIP-5 DIP-6

Protocol selcection Baute rate

PELCO-P OFF ON OFF OFF OFF OFF

Fig 5.2

3.4. Setup of the Baud Rate of Communication

As shown of figure 5.1, J8 set the protocol and baut rate of speed dome. DIP-4to

DIP-1 to choose the protocol, max 4 selection of baut rate.If the baut rate of contrller isn’t

standard, please adjust the baut rate the same with it.

Baut rate

2400bps OFF OFF

4800bps ON OFF

9600bps OFF ON

19200bps ON ON

Bate rate set

DIP-1 DIP-2 DIP-3 DIP-4 DIP-5 DIP-6

3.5. Selection of the Terminal Resistor of the Dome Camera

As shown of figure 5.1,J6 is the select switch of the 120 Ω terminal resistor on

the bus RS485, on which only one terminal resistor of the dome camera at the

farthest end can be connected, while the terminal resistors of other devices

should be opened.

J6, the tenth turn to be ON:120

terminal resistor is closed.

Ω terminal resistor is open; turn to be OFF: Ω

4. Shortcut control function

Preset N Set Preset N Call Preset N

1 Reserved

63 Open camera menu Open camera menu

64 Close the menu Open the menu

90 Reserved Reserved

91 Reserved Run the first patrol

92 Reserved Scan limit to left

93 Reserved Scan limit to right

94 Reserved Reserved

95 Close the menu Open the menu

96 Reserved Stop scan

97 Reserved Run the first scan

Twice Call Preset 1 within 4

seconds Open the menu

98 Reserved Reserved

If the built-in camera is

YOKO231, please set the 99

preset in advance, re-start the

speed dome, camera will work

correctly. Reserved

VI.Technical data table

Model CD55-SDI

Cam

characteristics

Sensor 1/2.8” 200W Exmor@ CMOS sensor

Zoom 20X optic/12X digital zoom

Lens F=4.7mm-94mm, f1.6-3.5,angle: 55.4°to 2.9°

Resolution 1080P/30FPS,1080P/25FPS

Min illumination

S/N ratio >50dB

Focus Auto or manual

White balance Auto or manual

WDR Auto or manual

Vide

enhancement

Privacy maskings Support

Shutter speed 1/1 to 1/10000sec

Gain control

PTZ

characteristics

PTZ degree

Speed

Preset 255 preset

Self-learning

track

Cruise track 6 tracks

Scanning track 3 tracks

Control mode

Idle protection 0 to 240s

Boot-up action Preset, tracks

Alarm I/O 1CH in/1CH out(optional)

Video output

Work Temperture

Size

Protection IP66

Power

Day:1.7LUX/1/30sec,night（ICR）0.0005LUX/1/3sec

White balance, mirror, color enhancement, DNR, slow shutter,gain

Auto or manual（-3DB-26DB,16STEPS）max.（6DB to 28DB，

Horizontal:360°，0.1°-240°/S，tilt 90°，0.1°-100°/S

Horizontal 380°/S，tilt 160°/S

RS485，baut rate 2400~19200bps

HD-SDI（BNC） 1.0Vp-p/75Ω

-30° to 65°，10~75% HR

215(diameter)mmX380（height）mm

DC12V / AC24V ， 50/60Hz

control

12STEPS）

auto

VII. Troubleshooting

Problem Probable cause Solution

On power no action

On power cannot self-check have image but have motor noise

Self-check ok, but have no image

Self-check ok but cannot control

Vague image

On power cannot control

Power supply fault Replace Bad connection of the powe Transformer damaged Replace Mechanical failure Repair Camera incline Reinstall Power supply not enoughReplace Video signal fault Reinstall Bad connection of the video Press to full connect Camera damaged Replace

RS485 Bus bad connection

Dome id setting is wron Protocol setting is wrong Reset and on power again Bad connection of the video Press to full connect Power supply not enough Replace Self check error On power again Bad connection of control Press to full connect Bad control of matrix On power again

Make correction

Check the RS485

connection

Reselect

Appendix : Lightning Proof and Surge Signal Proof

The product adopts TVS lightning proof technology to prevent from damage by lightning

strike below 1500 W and impulse signals such as surge; but it is also necessary to abide

by the following precautions to ensure electrical safety based on practical circumstances:

 Keep the communication cables at least 50 meters away from high voltage

equipment or cables.

 Make outdoor cable laying-out under eaves as possible as you can.

 In open area shield cables in steel tube and conduct a single point ground to the tube.

Trolley wire is forbidden in such circumstances.

 In strong thunderstorm or high faradic zone (such as high voltage transformer

substation), extra strong lightning proof equipment must be installed.

 Take the building lightning proof requirements into account to design the lightning

proof and grounding of outdoor equipment and cable laying-out in accordance with

the national and industrial standards.

 The system must be grounded with equal potentials. The earth ground connection

must satisfy the anti-interference and electrical safety requirements and must not

short circuited with high voltage electricity net. When the system is grounded

separately, the resistance of down conductor should be ≤ 4Ω and the sectional area

of down conductor should be ≤25mm2 (refer to Figure I).

<Fig>

Appendix : The Cleaning of Clear Down Cover

To obtain constant clear videos, user should clean the down cover periodically.

 Be cautious when cleaning. Hold the down cover ring only to avoid direct touch to the

acrylic down cover. The acid sweat mark of fingerprint will corrode the coating of

down cover and scratch on down cover will cause vague images.

 Use soft dry cloth or the substitute to clean the inner and outer surfaces.

 For hard contamination, use neutral detergent. Any cleanser for high grade furniture

is applicable.

Appendix III: RS485 Bus Basic Knowledge

1. Characteristics of RS485 Bus

As specified by RS485 standards, RS485 Bus is of half-duplex data transmission

cables with characteristic impedance as 120Ω. The maximum load capacity is 32 unit

loads (including main controller and controlled equipment).

2. Transmission distances of RS485 Bus

When user selects the 0.56mm (24AWG) twisted pair wires as data transmission

cable, the maximum theoretical transmitting distances are as follows:

Baud Rate Maximum Transmitting Distance

2400 Bps 1800m

4800 Bps 1200m

9600Bps 800m

If user selects thinner cables, or installs the dome in an environment with strong

electromagnetic interference, or connects lots of equipment to the RS485 Bus, the

maximum transmitting distance will be decreased. To increase the maximum

transmitting distance, do the contrary.

3. Connection and termination resistor

The RS485 standards require a daisy-chain connection between the equipment.

There must be termination resistors with 120Ωimpedance at both ends of the connection

(refer to Figure 20).

Please refer to Figure 21 for simple connection. “D” should not exceed 7m.

120Ω 120Ω

1# 2# 3# 4# 32#

Figure 20

. . . . .

A+

B-

A+ B-

.....

120Ω

Main controller

.....

1# 2# 3# 31#

120Ω

Figure 21

The connection of 120Ω termination resistor: The termination resistor is ready on the

Protocol PCB. There are two kinds of connection. Refer to the Protocol PCB jumper

setting form (refer to Picture 2).

1) In the Picture it is the factory default connection. The jumper is seated on

Pin2&Pin3 and the termination resistor is not connected.

2) when connecting the 120Ω termination resistor, user should plug the jumper on

Pin1&Pin2. and the termination resistor is connected.

4. Problems in practical connection

In some circumstances user adopts a star configuration in practical connection. The

termination resistors must be connected to the two equipment that are farthest away from

each other, such as equipment 1# and 15# in Picture 44. As the star configuration is not in

conformity with the requirements of RS485 standards, problems such as signal reflections,

lower anti-interference performance arise when the cables are long in the connection. The

reliability of control signals is decreased with the phenomena that the dome does not

respond to or just responds at intervals to the controller, or does continuous operation

without stop (refer to Figure III).

<Fig.  c>

MC2080

A+

B-

120Ω

< Fig.  d >

. . . .

16#

COP-USA CD55-H-SDI User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual