COP-USA CD45IRIP-9531 User Manual

Water-Proof Network Camera

UUsseerr MMaannuuaall

Please read this manual carefully for correct use of the product.

Notes

 Please use the specified power supply to connect.
 Do not attempt to disassemble the camera; in order to prevent electric shock, do not

remove screws or covers.

 There are no user-serviceable parts inside. Please contact the nearest service center as

soon as possible if there is any failure.

 Avoid from incorrect operation, shock vibration, heavy pressing which can cause

damage to product.

 Do not use corrosive detergent to clean main body of the camera. If necessary, please

use soft dry cloth to wipe dirt; for hard contamination, use neutral detergent. Any
cleanser for high grade furniture is applicable.

 Avoid aiming the camera directly towards extremely bright objects, such as, sun, as this

may damage the image sensor.

 Please follow the instructions to install the camera. Do not reverse the camera, or the

reversing image will be received.

 Do not operate it incase temperature, humidity and power supply are beyond the limited

stipulations.

 Keep away from heat sources such as radiators, heat registers, stove, etc.
 Do not expose the product to the direct airflow from an air conditioner.
 This is product instructions not quality warranty. We may reserve the rights of amending

the typographical errors, inconsistencies with the latest version, software upgrades and
product improvements, interpretation and modification. These changes will be published
in the latest version without special notification.

 When this product is in use, the relevant contents of Microsoft, Apple and Google will

be involved in. The pictures and screenshots in this manual are only used to explain the
usage of our product. The ownerships of trademarks, logos and other intellectual
properties related to Microsoft, Apple and Google belong to the above-mentioned
companies.

 This manual is suitable for water-proof network camera. All pictures and examples used

in the manual are for reference only. .

3 Megapixel IP Camera User Manual

Table of Contents

1 Introduction ................................................................................................................... 1

2 IE Remote Access ........................................................................................................... 2

2.1 LAN ........................................................................................................................ 2

2.1.1 Access through IP-Tool .................................................................................... 2

2.1.2 Directly Access through IE .............................................................................. 3

2.2 WAN ....................................................................................................................... 4

3 Remote Preview ............................................................................................................. 6

3.1 The Remote Preview Interface ............................................................................... 6

3.2 Record Playback ................................................................................................ ..... 6

3.3 Snap Pictures .......................................................................................................... 7

4 Remote Live Surveillance .............................................................................................. 9

4.1 System Configuration ............................................................................................. 9

4.1.1 Basic Information ............................................................................................. 9

4.1.2 Date & Time Configuration.............................................................................. 9

4.2 Video Configuration ............................................................................................. 10

4.2.1 Camera Configuration ................................ ................................ .................... 10

4.2.2 Video Stream .................................................................................................. 10

4.2.3 OSD Configuration ........................................................................................ 11

4.2.4 Video Mask .................................................................................................... 12

4.2.5 ROI Configuration ......................................................................................... 12

4.3 Alarm Configuration ............................................................................................ 13

4.3.1 Motion Detection Area ................................................................................... 13

4.3.2 Motion Detection Trigger ............................................................................... 14

4.3.3 Motion Detection Schedule ............................................................................ 15

4.4 Network Configuration ......................................................................................... 15

4.4.1 Port ................................................................................................................. 15

4.4.2 IP Address ................................................................ ...................................... 16

4.4.3 Server Configuration ...................................................................................... 16

4.4.4 IP Notify ......................................................................................................... 17

4.4.5 DDNS Configuration ..................................................................................... 17

4.4.6 RTSP ................................ ................................ .............................................. 18

4.4.7 UPnP .............................................................................................................. 19

4.4.8 Mail Setting .................................................................................................... 19

4.4.9 FTP ................................................................................................................ 20

4.5 Advanced Configuration....................................................................................... 20

4.5.1 User Configuration ......................................................................................... 21

4.5.2 Security Configuration ................................................................................... 22

4.5.3 Configure Backup & Restore ......................................................................... 23

4.5.4 Reboot Device ................................................................................................ 23

4.5.5 Upgrade .......................................................................................................... 23

5 Q & A ............................................................................................................................ 24

6 Specification ................................................................................................................. 26

Page 1

3 Megapixel IP Camera User Manual

1 Introduction

This IP-CAMERA (short for IP-CAM) is designed for high performance CCTV solutions. It
adopts state of the art video processing chips. It utilizes most advanced technologies, such as
video encoding and decoding technology, complies with the TCP/IP protocol, SoC, etc to
ensure this system more stable and reliable.
This product is widely used in banks, telecommunication systems, electricity power
departments, law systems, factories, storehouses, uptowns, etc. In addition, it is also an ideal
choice for surveillance sites with middle or high risks.

Main Features

 3MP（2048 × 1536）coding
 Max. resolution: 2048 × 1536
 ICR auto switch, true day/night
 3D DNR, digital WDR
 ROI coding
 10~20m IR night visible distance optional
 PoE power supply
 Support smart phone, iPad, remote monitoring
 Support P2P (NET Traversal)
 Vandal-proof

Page 2

3 Megapixel IP Camera User Manual

2 IE Remote Access

IP-CAM can be connected through LAN or WAN. Here only take IE browser (6.0) for
example. The details are as follows:

2.1 LAN

In LAN, there are two ways to access IP-CAM: 1. Access through IP-Tool; 2. Directly access
through IE browser.

2.1.1 Access through IP-Tool

① Make sure the PC and IP-CAM are connected to the LAN and the IP-Tool is installed in
the PC from the CD.

② Double click the IP-Tool icon on the desktop to run this software as shown below:

③ Modify the IP address. The default IP address of this camera is 192.168.226.201. Click the

information of the camera listed in the above table to show the network information on the
right hand. Modify the IP address and gateway of the camera and make sure its network

address is in the same local network segment as the computer’s. Please modify the IP address

of your device according to the practical situation.

For example, the IP address of your computer is 192.168.13.4. So the IP address of the camera

Page 3

3 Megapixel IP Camera User Manual

The default password of the administrator is “123456”.

The default username is “admin”; the default password is “123456”.

shall be changed to 192.168.13.X. After modification, please input the password of the
administrator and click “Modify” button to modify the setting.



④ Double click the IP address and then the system will pop up the IE browser to connect
IP-CAM. IE browser will automatically download the Active X control. After downloading, a

login window will pop up as shown below.

Input the username and password to log in.



2.1.2 Directly Access through IE

The default network settings are as shown below:

IP address: 192.168.226.201
Subnet Mask: 255.255.255.0
Gateway: 192.168.226.1
HTTP: 80
Data port: 9008
You may use the above default settings when you log in the camera for the first time.

① Manually set the IP address of the PC and the network segment should be as the same as
the default settings of the IP camera. Open the network and share center. Click “Local Area

Connection” to pop up the following window.

Page 4

3 Megapixel IP Camera User Manual

Select “Property” and then select internet protocol according to the actual situation (for
example: IPV4). Next, click “Property” button to set the network of the PC.

② Open the IE browser and input the default address of IP-CAM and confirm. The IE
browser will download Active X control automatically.

③ After downloading Active X control, the login dialog box will pop up.
④ Input the default username and password and then enter to view.

2.2 WAN

Take access the camera by the router or virtual server for example.

① Make sure the camera is well connected via LAN and then log in the camera via LAN and

Page 5

3 Megapixel IP Camera User Manual

go to the ConfigNetwork ConfigPort menu to set up the port number.

② Go to Config Network ConfigIP Address menu to modify the IP address.
③ Go to the router’s management interface through IE browser to forward the IP address and

port of the camera in the “Virtual Server”.

Port Setup IP Setup

Router Setup

④ Open the IE browser and input its WAN IP and http port to access.

Page 6

3 Megapixel IP Camera User Manual

3 Remote Preview

1

People icon

4

Zoom in

7

Start recording

2

Fix size

5

Zoom out

8

Playback

3

Actual size

6

Full screen

9

Snap

3.1 The Remote Preview Interface

Remote Preview

 When motion detection alarm is triggered, the people icon turns red.

Right click to pop up a pull-down list as shown below:

Stream: Three streams are optional.
Turn off the live: Click this item to close present live preview.
Full screen: The live preview picture will be full-screen display.

Double click or click right mouse to return to the previous
interface.

Online user: Display the current user connecting to the device.
System information: Display the device information: device

name, firmware version, software build date, kernel version and
hardware version.

3.2 Record Playback

Before you play the record files, please make sure you have recorded. You may click
button to record. Then click button to pop up a video player. Double click the record

file to play the video as shown below.

Page 7

3 Megapixel IP Camera User Manual

1

Play

5

Next frame

9

Zoom out

2

Pause

6

The previous file

10

Full screen

3

Stop

7

The next file

11

Path 4 Forward

8

Zoom in

12

Volume

3.3 Snap Pictures

Select the picture number and then click “Snap” icon as shown below.

Single Snap

User can snap multiple pictures. Select the picture number from Frame pull down list box,
such as 2, and check “Title” and “Time” to show capture title and time on the snap pictures
simultaneously.

Page 8

3 Megapixel IP Camera User Manual

Multi-picture Snap

Click “Browse” to set saving path. Click “Save” to save pictures to HDD on the computer;
Click “Printer setup” to set the printer and print the snap pictures; drag the scroll bar to view

all snapped pictures.

Page 9

3 Megapixel IP Camera User Manual

4 Remote Live Surveillance

Functions of remote configurations include: System Configuration, Video Configuration,
Alarm Configuration, Network Configuration and Advanced Configuration. User should
firstly select the menu on the left, and then set the relative parameters.

4.1 System Configuration

The “System configuration” includes two submenus: Basic Information and Date & Time.

4.1.1 Basic Information

In the basic information interface, user can set up the device name and also can check the
relative information of the server.
Setting steps:

1. Clicking the “Config” icon will appear the menu list.

2. Clicking the “Basic Information” will pop up a window as shown below.

3. Input the name of the device in the “Device name” text box.

4. Press the “Save” button to save the settings.

4.1.2 Date & Time Configuration

Setting steps:

1. Go to “System Configuration”  “Date & Time”.

2. Set time zone.

Page 10

3 Megapixel IP Camera User Manual

3. Enable DST mode as required.

4. Set time. You may set time manually or enable NTP.

4.2 Video Configuration

Camera Configuration includes five submenus: Camera Configuration, Video Stream, OSD
Config, Video Mask and ROI Config.

4.2.1 Camera Configuration

Setting steps:

1. Go to “Video Configuration”  “Camera” interface as shown below.

2. You may adjust frequency, brightness, contrast, hue and saturation of the picture.

3. Select white balance mode.

4. Wide dynamic, sharpen and denoise are adjustable.

5. You can also set day-night mode and enable the image mirror and image overturn function.

6. Press the “Save” button to save the settings.

4.2.2 Video Stream

Go to “Video configuration”  “Video Stream” to see an interface as shown below.

Three video streams can be adjustable.

Page 11

3 Megapixel IP Camera User Manual

Resolution: The higher the resolution is, the clearer the image is.
Frame rate: The higher the frame rate is, the more fluency the video is. However, more

storage room will be taken up.
Bitrate type: Including CBR and VBR. CBR means that no matter how changeable the video
resources are, the compression bitrate keeps constant. This will not only facilitate the image
quality better in a constant bitrate but also help to calculate the capacity of the recording.
VBR means that the compression bitrate can be adjustable according to the change of the
video resources. This will help to optimize the network bandwidth.
Video Quality: When VBR is selected, you need to choose image quality. The higher the
image quality you choose, the more bitrate will be required.

Bitrate: Please choose it according to the actual network situation.
I Frame interval: It is recommended to use the default value. If the value is over high, the

read speed of the group of pictures will be slow resulting in the quality loss of the video.
Video encoding profile: Baseline, main and high profile are optional. Baseline profile is
mainly used in interactive application with low complexity and delay. Main/high profile is
mainly used for higher coding requirement.

Alarm picture size: Please select it according to the actual situation.
Video encode slice split: If enabled, you may get more fluency image even though using the

low-performance PC.

4.2.3 OSD Configuration

Go to “Video Config”  “OSD Config” menu to display the interface as shown below.
You may set time stamp, device name and custom OSD here. Drag the time stamp and custom
OSD to set their position. Then press the “Save” button to save the settings.

Page 12

3 Megapixel IP Camera User Manual

4.2.4 Video Mask

You can set 4 mask areas at most.

To set up video mask

1. Enable video mask and select mask color.

2. Click “Draw” button and then drag the mouse to draw the video mask area.

3. Click “Save” button to save the settings.

4. Return to the live to see the following picture.

Clear the video mask:
Go to video mask menu and then click “Clear” button to delete the current video mask area.

4.2.5 ROI Configuration

To set up ROI

1. Go to ConfigROI Config menu.

Page 13

3 Megapixel IP Camera User Manual

2. Check “Enable” and then click “Draw” button.

3. Drag the mouse to set the ROI area.

4. Set the level.

5. Click “Save” button to save the settings.
Now, you will see the selected ROI area is clearer than other areas especially in low bitrate
condition.

4.3 Alarm Configuration

Alarm configuration includes three submenus: Motion Detection Area, Motion Detection
Trigger and Motion Detection Schedule.

4.3.1 Motion Detection Area

1. Go to “Alarm configuration”  “Motion Detection Area” to see an interface as shown
below.

2. Move the “Sensitivity” scroll bar to set up the motion trace sensitivity.

3. Check “Add”, press the “Ctrl” button and move mouse to select the motion detection area;
Select “Erase” and move the mouse to clear all motion detection area.

Page 14

3 Megapixel IP Camera User Manual

4. Press the “Save” button to save the settings.

4.3.2 Motion Detection Trigger

1. Go to “Alarm Configuration”  “Motion Detection Trigger” to display an interface as
shown below.

2. Check “Enable alarm” check box. Then all functions under this interface will be activated.

3. Trigger Email: Check “Attach picture” and select email addresses in the “Receival email
address” text box (Email address shall be set first in the Mail config interface). Then the
triggered snap pictures will be sent into those addresses. User can also define the subject and
content of the email.

4. Trigger FTP: Check “Uploading picture”. Then the triggered snap pictures will be sent into
FTP server address.

Note: Please refer to FTP configuration chapter for more details.

Page 15

3 Megapixel IP Camera User Manual

6. Press the “Save” button to save the settings.

4.3.3 Motion Detection Schedule

Go to “Alarm configuration”  “Motion Detection schedule” interface as shown below.
Week schedule

User could set the alarm time from Monday to Sunday for alarm everyday in one week.
Note: The lengthwise means one day of a week; the rank means 24 hours of a day. Click on
the pane to set the alarm hours. Green means selected area. Blank means unselected area.
Add: Add the schedule for a special day.
Erase: Delete holiday schedule.

Day schedule

User could set alarm time for alarm at a certain time of special day, such as holiday.

1. Select a date at the “Date” pull down list, press “Add” button to add that date to the list box
on the right side and then move the scroll bar to set the schedule of that day.

2. Select a date in the list box on the right side, and press “Erase” to remove the schedule on
that day.
Press the “Save” button to save the settings.

Note: Holiday schedule is prior to Week schedule.

4.4 Network Configuration

Network configuration includes eight submenus: Port, IP Address, Server Configuration, IP
Notify, DDNS Config, RTSP, UPnP, Mail Setting and FTP.

4.4.1 Port

1. Go to “Network config” “Port” to see the interface as shown below.

Page 16

3 Megapixel IP Camera User Manual

2. Input port number for IE access in the “HTTP Port” textbox.

3. Input the port number for audio & video transmission in the “Data Port” textbox.

4.4.2 IP Address

1. Go to “Network Configuration” “IP Address” to see an interface shown below.

2. There are two options for IP setup: obtain an IP address automatically by DHCP protocol
and use the following IP address. You may choose one of options as required.

3. Use the following IP address: display the IP address, subnet mask, gateway and DNS of the
device.

4. PPPoE: User needs to manual input the user name and password for dial-up internet.
Firstly, log in IE clients and then enter user name and password of PPPoE, save the setting
and exit. Secondly, set up IP address change notice. Thirdly, connect with Modem. Then the
device will dial up internet automatically.

5. Press the “Save” button to save the settings.

4.4.3 Server Configuration

Go to “Network Configuration” “Server Config”.

Page 17

3 Megapixel IP Camera User Manual

1. Check “Do you want IP Camera to connect Server”.

2. Check the IP address and port of the transfer media server in the CMS/NVMS. Then enable
the auto report in the CMS/NVMS when adding a new device. Next, self-define the device ID
and input the remaining information of the device in the CMS/NVMS.

3. Input the above-mentioned server IP, server port and device ID in the relevant boxes.

4. Click “Save” button to save the settings.

4.4.4 IP Notify

1. Go to “Network Configuration” “IP Notify” to see a tab as shown below.

2. If the “Enable notifying change of IP” is selected, when the IP address of the device is
changed, a new IP address will be sent to the appointed mailbox automatically; If “FTP” is

selected, when the IP address of the device is changed, a new IP address will be sent to FTP
server.

4.4.5 DDNS Configuration

1. Go to “Network Configuration” “DDNS Configuration” tab as shown below.

2. Apply for a domain name. Take www. dvrdydns.com for example.

Page 18

3 Megapixel IP Camera User Manual

Input www.dvrdydns.com in the IE address bar to visit its website. Then click “Registration”
button to register as shown below.

Create domain name.

After you successfully request your domain name, you will see your domain in the list.

3. Select the server type and then input the username, password and domain name you apply
for in the DDNS configuration interface.

4. Click “Save” button to save the settings.

4.4.6 RTSP

Go to “Network Configuration” “RTSP” interface as shown below.

Page 19

3 Megapixel IP Camera User Manual

1. Select “Enable RTSP server”.

2. RTSP Port: Access Port of the streaming media. The default number is 554.

3. RTSP Address: The RTSP address you need to input in the media player.

4. You can also choose to enable anonymous viewer login.

4.4.7 UPnP

Go to “Network Configuration” “UPnP” interface as shown below.
Select “Enable UPnP” and then input friendly name.

Then double click “Network” icon on the desktop of the PC to see an icon with the friendly

name and IP address of the camera. You may quickly access the device by double clicking
this icon.

4.4.8 Mail Setting

Go to “Network Configuration”  “Mail Setting” interface.

1. From Email: Sender’s e-mail address.

Page 20

3 Megapixel IP Camera User Manual

Parameter

Meaning

Server name

The name of the FTP server

Server address

The address of the FTP server

Port

The port number of the FTP server

User name

The user name of the FTP server

Password

The password of the FTP server

Path

The save path for FTP files

2. User name and password: Sender’s user name and password.

3. Server address: SMTP name of sender.

4. Select the secure connection type at the Secure Connection pull down list according to user’
actual needs.

5. Receival email address list: Add email address into the list.

6. Receival email address: Receiver’s e-mail address.

7. After all parameters set up, you can click “Test your account settings”. If email sent
successful, a “Test Successful” window will pop up, if not, you can try other email addresses
or check the setting.

Notice: If you change the static IP into PPPoE and select mailbox, there will be an e-mail sent
to your mail box for notifying a new IP address.

4.4.9 FTP

Go to Network ConfigurationFTP interface as shown below.

1. Add: Click Add button to input FTP server’s server name, address, port number, user name,
password and upload path. Then click OK to confirm the setting.

2. Modify: Click this button to change the information of the FTP server.

3. Delete: Select a FTP account and click this button to delete this account.

4. Test: Select a FTP account and click this button to test its validity.
Please refer to the following table for parameters and instructions of FTP configuration.

4.5 Advanced Configuration

Advanced configuration includes four submenus: User Configuration, Security Configuration,
Configure Backup & Restore, Reboot and Upgrade.

Page 21

3 Megapixel IP Camera User Manual

4.5.1 User Configuration

Go to “User Configuration” interface.

Add user:

1. Clicking “Add” button pops up “Add User” dialog box.

User Configuration Add User

Note: After binding physical address to the IP-CAM, you can access the device on this PC

only. If the MAC address is “00:00:00:00:00:00”, it means that it can be connected to any
computers.

2. Input user name in “User Name” textbox (only letters).

3. Input characters in “Password” and “Confirm Password” textbox (letters or numbers).

4. Input the MAC address of the PC in “Binding MAC address” textbox.

5. Click “OK” button and then the new added user will display in the user list.

Modify user:

1. Select the user you want to modify password and physical address in the user configuration
list box.

2. Clicking “Modify” button will pop up “Modify user” dialog box as shown below.

Modify User

3. Input original password of this user in the “Password” text box.

4. Input new password in the “New password” and “Confirmation” text box.

5. Input computer’s physical address which is used to access the server in the “User PC MAC”

text box.

6. Click “OK” button to modify password and binding MAC address successfully.

Page 22

3 Megapixel IP Camera User Manual

Parameter

Meaning

User Name

User name to operate the logon client end

User Type

Type of users, normal user, advanced user and super administrator

Binding MAC address

The MAC addresses of user access the server which should set up
according to actual MAC address of server.

Password

Password to log in the client terminal

Confirm Password

Password to log in the client terminal

Delete user:

1. Select the user you want to delete in the user configuration list box.

2. Click “Delete” button to pop up a confirm dialog box. Then click “OK” to delete the user.

Note: The default super administrator cannot be deleted.

4.5.2 Security Configuration

1. Go to Advanced ConfigurationSecurity Configuration to see a tab shown below.

2. Check “Enable IP address” check box, select “Deny the following IP address”, input IP

address in the IP address list box and click “Add” button. Then this IP address will display in
the list box; the operation step of “Allow the following IP address” is the same as that of
“Deny the following IP address”.

3. Select the IP address you want to delete from the IP address list box and click “Delete”
button to delete that IP address.

4. Check “Enable MAC address” check box, select “Deny the following IP address”, input

MAC address in the MAC address list box and click “Add” button. Then this MAC address
will display in the list box; the operation step of “Allow the following MAC address” is the

same as that of “Deny the following IP address”.

5. Select the MAC address you want to delete from the MAC address list box and click
“Delete” button to delete that MAC address.

6. Click “Save” button to save the above setting.

Page 23

3 Megapixel IP Camera User Manual

4.5.3 Configure Backup & Restore

Go to Advanced configurationConfigure Backup & Restore Interface.

 Import & Export Configuration:

1. Click “Browse” to select save path for import or export information on PC.

2. You can import or export all setting information, but those two settings “User
Configuration” and “Network Configuration” are exceptional.

 Default Configuration

Click “Load default” button to restore all system settings to the default status.

4.5.4 Reboot Device

Go to Advanced configuration—Reboot device to see an interface as shown below.
Click “Reboot device” button to reboot the device.

4.5.5 Upgrade

Go to Advanced Configuration—Upgrade interface as shown below.

1. Click “Browse” button to select the save path of the upgrade file.

2. Click “Upgrade server firmware” button to start upgrading the application program.

3. The device will restart automatically. After you successfully update the software, click
“OK” button to close IE and then re-open IE to connect IP-CAM.

Notice: Do not shut down the PC or close the IP-CAM during upgrade.

Page 24

3 Megapixel IP Camera User Manual

5 Q & A

Q: How to find my password if I forget it?

A：Reset the device to the default factory settings by IP-Tool.
Default IP: 192.168.226.201
User name: admin
Password: 123456

Q：Fail to connect devices through IE browser, why?

A: Network is not well connected. Please check the connection and make sure it is connected
well.
B: IP is not available. Reset the valid IP.
C: Web port number has been revised: contact administrator to get the correct port number.
D: Exclude the above reasons. Recover default setting by IP-Tool.
Note: Default IP: 192.168.226.201，mask number: 255.255.255.0

Q：IP tool cannot search devices, why?

A：It may be caused by the anti-virus software in your computer. Please exit it and try to
search device again.

Q：IE cannot download ActiveX control. How can I do?

a. IE browser blocks ActiveX. Please do setup following below.

① Open IE browser. Click Tools-----Internet Options….

② Select Security------Custom Level….
③ Enable all the sub options under “ActiveX controls and plug-ins”.

Page 25

3 Megapixel IP Camera User Manual

④ Then click OK to finish setup.
b. Other plug-ins or anti-virus blocks ActiveX. Please uninstall or close them.

Q：No sound can be heard, why?

A：Audio input device is not connected. Please connect and try again.
B: Audio function is not enabled at the corresponding channel. Please check AUDIO item to
enable this function.

Page 26

3 Megapixel IP Camera User Manual

6 Specification

Model

3 Megapixel Water-proof Network Dome Camera

Camera

Image Sensor

1/3＂CMOS

Image Size

2048 × 1536

Electronic Shutter

1/25s~1/100000s

Auto Iris

Fixed Iris

Min. Illumination

0 Lux (IR ON)

Lens

3.6mm (6mm, 8mm optional)

Day-Night Switch

ICR auto switch

WDR

Digital WDR

DNR

3D noise reduction

Image

Video Compression

H.264/MJPEG

Encode Mode

VBR/CBR

Image Quality

Five levels VBR; Freely adjustable under CBR

Bitrate

64Kbps~8Mbps

Resolution

3MP(2048 × 1536), 1080P(1920 × 1080), 720P(1280 ×

720), D1, CIF, 480 × 240

Multi-streams

3MP（1~15fps）/1920 × 1080（1~30fps）
1280 × 720（1~10fps）/D1（1~30fps）/CIF（1~30fps）
CIF（1~30fps）/480 × 240（1~30fps）

Image Settings

Saturation, Brightness, Chroma, Contrast, Wide Dynamic,
Sharpen, NR, etc., adjustable through client software or
web browser

ROI

Support

Interface

Network

RJ45

Function

Remote Monitoring

IE browsing, CMS remote control

Online Connection

Support simultaneous monitoring for up to 10 users;
Support multi-stream real time transmission

Network Protocol

TCP/IP, UDP, DHCP, NTP, RTSP, PPPoE, DDNS, SMTP,
FTP

Interface Protocol

ONVIF, GB-T/28181-2011

Storage

Network remote storage

Smart Alarm

Motion Alarm

PoE Power Supply

Support

IR Distance

No (10-20 m optional)

Vandal-proof

IK10

Water-proof

IP66

Others

Power Supply

DC12V/PoE

Power Consumption

< 3W (ICR OFF); < 5.5W (ICR ON)

Working Environment

-20℃~50℃, 10%~90% humidity

Dimension

Φ 116mm ×91mm

Weight（Net）

560g

A1