3 Megapixel
Network
Camera
User Manual
Please read this instruction carefully for correct use of the product and preserve it for
reference purposes
Notes on Safety
Please use the specified power supply to connect.
Do not attempt to disassemble the camera; in order to prevent electric shock, do not
remove screws or covers.
There are no user-serviceable parts inside. Please contact the nearest service center as
soon as possible if there is any failure.
Avoid from incorrect operation, shock vibration, heavy pressing which can cause
damage to product.
Do not use corrosive detergent to clean main body of the camera. If necessary, please
use soft dry cloth to wipe dirt; for hard contamination, use neutral detergent. Any
cleanser for high grade furniture is applicable.
Avoid aiming the camera directly towards extremely bright objects, such as, sun, as this
may damage the image sensor.
Please follow the instructions to install the camera. Do not reverse the camera, or the
reversing image will be received.
Do not operate it incase temperature, humidity and power supply are beyond the limited
stipulations.
Keep away from heat sources such as radiators, heat registers, stove, etc.
Do not expose the product to the direct airflow from an air conditioner.
This is product instructions not quality warranty. We may reserve the rights of amending
the typographical errors, inconsistencies with the latest version, software upgrades and
product improvements, interpretation and modification. These changes will be published
in the latest version without special notification.
When this product is in use, the relevant contents of Microsoft, Apple and Google will
be involved in. The pictures and screenshots in this manual are only used to explain the
usage of our product. The ownerships of trademarks, logos and other intellectual
properties related to Microsoft, Apple and Google belong to the above-mentioned
companies.
This manual is suitable for IR water-proof network camera. All pictures and examples
used in the manual are for reference only.
Table of Contents
1 Introduction ................................................................................................................... 1
2 IE Remote Access ........................................................................................................... 2
2.1 LAN ................................................................................................................... 2
2.1.1 Access through IP-Tool ............................................................................ 2
2.1.2 Directly Access through IE ....................................................................... 3
2.2 WAN .................................................................................................................. 5
3 Remote Preview ............................................................................................................. 8
3.1 The Remote Preview Interface ........................................................................... 8
4 Remote Live Surveillance .............................................................................................. 9
4.1 System Configuration ........................................................................................ 9
4.1.1 Basic Information ..................................................................................... 9
4.1.2 Date & Time ............................................................................................. 9
4.1.3 Local Configuration ................................................................................ 10
4.2 Image Configuration ........................................................................................ 10
4.2.1 Display Configuration ............................................................................ 10
4.2.2 Video Stream .......................................................................................... 11
4.2.3 OSD Configuration ................................................................................. 12
4.2.4 Video Mask ............................................................................................ 12
4.2.5 ROI Configuration .................................................................................. 13
4.3 Alarm Configuration ........................................................................................ 14
4.3.1 Motion Detection .................................................................................... 14
4.3.2 Alarm Server .......................................................................................... 16
4.4 Network Configuration .................................................................................... 17
4.4.1 TCP/IPv4 ................................................................................................ 17
4.4.2 Port ......................................................................................................... 18
4.4.3 Central Server ......................................................................................... 18
4.4.4 DDNS Configuration .............................................................................. 18
4.4.5 SNMP ..................................................................................................... 20
4.4.6 RTSP ....................................................................................................... 21
4.4.7 UPNP ...................................................................................................... 21
4.4.8 Mail configuration .................................................................................. 21
4.4.9 FTP Setting ............................................................................................. 22
4.5 Security Configuration ..................................................................................... 23
4.5.1 User Configuration ................................................................................. 23
4.5.2 Online Video User .................................................................................. 25
4.5.3 Block and Allow List .............................................................................. 25
4.6 Maintenance ..................................................................................................... 25
4.6.1 Backup & Restore ................................................................................... 25
4.6.2 Reboot Device ........................................................................................ 26
4.6.3 Upgrade .................................................................................................. 26
4.6.4 Log ......................................................................................................... 27
Network Camera User Manual
5 Search ........................................................................................................................... 28
Appendix ................................................................................................................................ 29
Appendix 1 Q & A ................................................................ ................................ .............. 29
Appendix 2 Specifications .................................................................................................. 31
Network Camera User Manual
1 Introduction
This IP-CAMERA (short for IP-CAM) is designed for high performance CCTV solutions. It
adopts state of the art video processing chips. It utilizes most advanced technologies, such as
video encoding and decoding technology, complies with the TCP/IP protocol, SoC, etc to
ensure this system more stable and reliable.
This product is widely used in banks, telecommunication systems, electricity power
departments, law systems, factories, storehouses, uptowns, etc. In addition, it is also an ideal
choice for surveillance sites with middle or high risks.
Main Features
ICR auto switch, true day/night
3D DNR, digital WDR
ROI coding
Support smart phone, iPad, remote monitoring
Surveillance Application
1
Network Camera User Manual
2 IE Remote Access
You may connect IP-Cam via LAN or WAN. Here only take IE browser (6.0) for example. The
details are as follows:
2.1 LAN
In LAN, there are two ways to access IP-Cam: 1. access through IP-Tool; 2. directly access
through IE browser.
2.1.1 Access through IP-Tool
Network connection:
① Make sure the PC and IP-Cam are connected to the LAN and the IP-Tool is installed in the
PC from the CD.
② Double click the IP-Tool icon on the desktop to run this software as shown below:
③ Modify the IP address. The default IP address of this camera is 192.168.226.201. Click the
information of the camera listed in the above table to show the network information on the
right hand. Modify the IP address and gateway of the camera and make sure its network
address is in the same local network segment as the computer’s. Please modify the IP address
2
Network Camera User Manual
The default password of the administrator is “123456”.
The default username is “admin”; the default password is “123456”.
of your device according to the practical situation.
For example, the IP address of your computer is 192.168.1.4. So the IP address of the camera
shall be changed to 192.168.1.X. After modification, please input the password of the
administrator and click “Modify” button to modify the setting.
④ Double click the IP address and then the system will pop up the IE browser to connect
IP-CAM. IE browser will auto download the Active X control. After downloading, a login
window will pop up as shown below.
Input the username and password to log in. If you input the wrong password for the first time,
you shall wait for 10 seconds and then input the right password.
2.1.2 Directly Access through IE
The default network settings are as shown below:
IP address: 192.168.226.201
Subnet Mask: 255.255.255.0
3
Network Camera User Manual
Gateway: 192.168.226.1
HTTP: 80
Data port: 9008
You may use the above default settings when you log in the camera for the first time. You may
directly connect the camera to the computer through network cable.
① Manually set the IP address of the PC and the network segment should be as the same as
the default settings of the IP camera. Open the network and share center. Click “Local Area
Connection” to pop up the following window.
Select “Properties” and then select internet protocol according to the actual situation (for
example: IPv4). Next, click “Properties” button to set the network of the PC.
4
Network Camera User Manual
② Open the IE browser and input the default address of IP-CAM and confirm. The IE
browser will download Active X control automatically.
③ After downloading Active X control, the login dialog box will pop up.
④ Input the default username and password and then enter to view.
2.2 WAN
Access through the router or virtual server
① Make sure the camera is well connected via LAN and then log in the camera via LAN. Go
to ConfigNetwork Port menu to set the port number.
② Go to Config Network TCP/IPv4 menu to modify the IP address.
5
Network Camera User Manual
③ Go to the router’s management interface through IE browser to forward the IP address and
port of the camera in the “Virtual Server”.
Router Setup
④ Open the IE browser and input its WAN IP and http port to access.
Access through PPPoE dial-up
Network connection
You may access the camera through PPPoE auto dial-up. The setting steps are as follow:
6
Network Camera User Manual
① Go to ConfigNetwork Port menu to set the port number.
② Go to Config Network TCP/IPv4PPPoE Config menu. Check “Enable ” and then
input the user name and password which you can get from your internet service provider.
③ Go to Config Network DDNS menu. Before you configure the DDNS, please apply for
a domain name first. Please refer to DDNS Configuration for detail information.
④ Open the IE browser and input the domain name and http port to access.
Access through static IP
Network connection
The setting steps are as follow:
① Go to ConfigNetwork ConfigPort menu to set the port number.
② Go to Config Network ConfigIP Address menu to set the IP address. Check “Use the
following IP address” and then input the static IP address and other parameters.
③ Open the IE browser and input its WAN IP and http port to access.
7
Network Camera User Manual
Icon
Description
Icon
Description
Motion alarm indicator
icon
Start/stop live view
Original size
Snap
Appropriate size
Start/stop record
Auto
Zoom in
Full screen
Zoom out
3.1 The Remote Preview Interface
After you log in, you will see the following window.
3 Remote Preview
The following table is the instructions of the icons on the remote preview interface.
When motion detection alarm is triggered, the people icon will turn red.
In full screen mode, right click to exit.
8
Network Camera User Manual
4 Remote Live Surveillance
4.1 System Configuration
The “System Configuration” includes three submenus: Basic Information, Date & Time and
Local Configuration.
4.1.1 Basic Information
In the Basic Information interface, you can check the relative information of the device.
4.1.2 Date & Time
Go to ConfigSystemDate and Time. Please refer to the following interface.
You can select the time zone and DST as required.
Click “Date and Time” to set the time mode .
9
Network Camera User Manual
4.1.3 Local Configuration
Go to ConfigSystemLocal Config. You can set the storage path of the captured pictures
and video records.
4.2 Image Configuration
Image Configuration includes five submenus: Display, Video/Audio, OSD, Video Mask and
ROI Config.
4.2.1 Display Configuration
Many parameters of the camera can be set in display configuration interface such as brightness,
contrast, chroma, saturation wide dynamic, etc.
10
Network Camera User Manual
Brightness: Set the brightness level of the camera’s image.
Contrast: Set the color difference between the brightest and darkest parts.
Chroma: Set the total color degree of the image.
Saturation: Set the degree of color purity. The purer the color is, the brighter the image is.
Wide Dynamic: It helps the camera provide clear images even under back light
circumstances. When there are both very bright and very dark areas simultaneously in the
field of view, WDR balances the brightness level of the whole image and provide clear images
with details.
Sharpness: Set the resolution level of the image plane and the sharpness level of the image
edge.
Denoise: Decrease the noise and make the image more thorough. Increasing the value will
make the noise reduction effect better but it will reduce the image resolution.
White Balance: Adjust the color temperature according to the environment automatically.
Frequency: 50HZ and 60HZ can be optional.
Day-night Mode: Please choose the mode as needed.
Sensitivity: High, middle and low can be selected.
Infrared Mode: You may choose “ ON”, “OFF” and “Auto” as required.
Image Mirror: Reverse the current video image right and left.
Image Flip: Turn the current video image upside down.
4.2.2 Video Stream
The following interface will be displayed by clicking ConfigImageVideo/Audio.
In this interface, you can set the resolution, frame rate, bitrate type, video quality and so on
subject to the actual network condition.
Three video streams can be adjustable.
Resolution: The higher the resolution is, the clearer the image is.
Frame rate: The higher the frame rate is, the more fluency the video is. However, more storage
room will be taken up.
Bitrate type: Including CBR and VBR. CBR means that no matter how changeable the video
11
Network Camera User Manual
resources are, the compression bitrate keeps constant. This will not only facilitate the image
quality better in a constant bitrate but also help to calculate the capacity of the recording. VBR
means that the compression bitrate can be adjustable according to the change of the video
resources. This will help to optimize the network bandwidth.
Video Quality: When VBR is selected, you need to choose image quality. The higher the image
quality you choose, the more bitrate will be required.
Bitrate: Please choose it according to the actual network situation.
I Frame interval: It is recommended to use the default value. If the value is over high, the
read speed of the group of pictures will be slow resulting in the quality loss of the video.
Video encoding profile: Baseline and main profile are optional. Baseline profile is mainly
used in interactive application with low complexity and delay. Main profile is mainly used for
higher coding requirement.
Stream of snapping photos: Please select it according to the actual situation.
Video encode slice split: If enabled, you may get more fluency image even though using the
low-performance PC.
Watermark: If selected, you can input the watermark theme. You may check the watermark
when playing back the local record in the search interface, lest the record files is tampered.
4.2.3 OSD Configuration
Go to ConfigImageOSD menu to display the interface as shown below:
You may set time stamp, device name and OSD here. After enabling the corresponding display
and entering the content, drag them to change their position. Then press the “Save” button to
save the settings.
4.2.4 Video Mask
Go to ConfigImageVideo Mask menu to display the interface as shown below. You can set
4 mask areas at most.
12
Network Camera User Manual
To set up video mask
1. Open video mask.
2. Click “Draw Area” button and then drag the mouse to draw the video mask area.
3. Click “Save” button to save the settings.
4. Return to the live to see the following picture.
Clear the video mask:
Go to video mask menu and then click “Clear” button to delete the current video mask area.
4.2.5 ROI Configuration
To set up ROI
1. Go to Video ConfigROI Config menu.
13
Network Camera User Manual
2. Check “Open” and then click “Draw Area” button.
3. Drag the mouse to set the ROI area.
4. Set the level.
5. Click “Save” button to save the settings.
Now, you will see the selected ROI area is clearer than other areas especially in low bitrate
condition.
4.3 Alarm Configuration
Alarm configuration includes two submenus: Motion Detection and Alarm Server.
4.3.1 Motion Detection
To set motion detection:
1. Go to ConfigAlarmMotion Detection to set motion detection alarm.
14
Network Camera User Manual
Check “Enable Alarm” check box to activate motion based alarm, choose alarm holding time
and set alarm trigger options.
Trigger Email: If the email and attach picture checkbox is checked (Email address shall be set
first in the Mail config interface), the triggered snap pictures and event will be sent into those
addresses.
Trigger FTP: If “Uploading picture” is checked, the triggered snap pictures will be sent into
FTP server address. Please refer to FTP configuration chapter for more details.
2. Set motion detection area and sensitivity. Click “Area and Sensitivity” tab to see the
following sub-menu.
Move the “Sensitivity” scroll bar to set the sensitivity.
Check “Add” and click “Draw” button and move mouse to select the motion detection area;
Select “Erase” and move the mouse to clear motion detection area.
After that, click “Save” to save the settings.
3. Set the schedule of the motion detection. Click “Schedule” tab to set the schedule of the
motion detection.
15
Network Camera User Manual
Week schedule
Set the alarm time from Monday to Sunday for alarm everyday in one week. The lengthwise
means one day of a week; the rank means 24 hours of a day. Green means selected area. Blank
means unselected area.
“Add”: Add the schedule for a special day.
“Erase”: Delete holiday schedule.
Day schedule
Set alarm time for alarm in some time of a special day, such as holiday.
Select a date at the “Date” pull down list, press “Add” button to add that date to the list box on
the right side and then move the scroll bar to set the schedule of that day.
Select a date in the list box on the right side, and press “Delete” to remove the schedule on that
day.
Press the “Save” button to save the settings.
Note: Holiday schedule is prior to Week schedule.
4.3.2 Alarm Server
Go to “Alarm configuration” “Alarm Server” interface as shown below.
You may input the alarm server address and port. When the alarm happens, the camera will
automatically transfer the alarm event to the alarm server. If the alarm server is not used, there
is no need for you to configure here.
16
Network Camera User Manual
4.4 Network Configuration
4.4.1 TCP/IPv4
Go to ConfigNetworkTCP/IPv4. There are two ways for network connection.
Use IP address. There are two options for IP setup: obtain an IP address auto by DHCP
protocol and use the following IP address. Please choose one of options for your requirements.
Use PPPoE: Enter the user name and password from your ISP.
You can choose either way of the network connection. If you use PPPoE to connect internet,
you will get a dynamic WAN IP address. This IP address will change frequently. You may use
the function of IP change notification.
17
Network Camera User Manual
Trigger Email: when the IP address of the device is changed, a new IP address will be sent to the
appointed mailbox automatically
Trigger FTP: when the IP address of the device is changed, a new IP address will be sent to FTP
server.
4.4.2 Port
Go to ConfigNetworkPort. HTTP port, Data port and RTSP port can be set.
HTTP Port: The default HTTP port is 80. It can be changed to any port which is not occupied.
Data Port: The default data port is 9008. Please change it as required.
RTSP Port: The default port is 554. Please change it as required.
4.4.3 Central Server
This function is mainly used for connecting network video management system.
1. Check “Enable”.
2. Check the IP address and port of the transfer media server in the ECMS/NVMS. Then enable
the auto report in the ECMS/NVMS when adding a new device. Next, input the remaining
information of the device in the ECMS/NVMS. After that, the system will auto allot a device ID.
Please check it in the ECMS/NVMS.
3. Input the above-mentioned server address, server port and device ID in the responding boxes.
Click “Save” button to save the settings.
4.4.4 DDNS Configuration
If your camera is set to use PPPoE as its default network connection, DDNS should be set for
network access. Before you set the DDNS, please make sure you have registered a domain
name on the DDNS server.
1. Go to ConfigNetwork DDNS.
18
Network Camera User Manual
2. Apply for a domain name. Take www. dvrdyndns.com for example. Input
www.dvrdydns.com in the IE address bar to visit its website. Then click “Registration” button.
Create domain name.
After you successfully request your domain name, you will see your domain in the list.
19
Network Camera User Manual
3. Input the username, password, domain you apply for in the DDNS configuration interface.
4. Click “Save” button to save the settings.
4.4.5 SNMP
To get camera status, parameters and alarm information and remotely manage the camera, you
can set the SNMP function. Before using the SNMP, please download the SNMP software and
set the parameters of the SNMP, such as SNMP port, trap address.
1. Go to ConfigNetworkSNMP.
2. Check the corresponding version checkbox (Enable SNMPv1, Enable SNMPv2, Enable
20
Network Camera User Manual
SNMPv3) according to the version of the SNMP software you download.
3. Set the “Read SNMP Community”, “Write SNMP Community”, “Trap Address”, “Trap Port”
and so on. Please make sure the settings are the same as that of your SNMP software.
Note: Please use the different version in accordance with the security level you required. The
higher the version is, the higher the level of the security is.
4.4.6 RTSP
Go to ConfigNetworkRTSP.
1. Select “Enable”.
2. RTSP Port: Access port of the streaming media. The default number is 554.
3. RTSP Address: The RTSP address you need to input in the media player.
4. Check “Enable anonymous viewer login…”.
4.4.7 UPNP
If you enable this function, you can quickly access the camera via LAN and you don’t need to
configure the port mapping when the camera is connected to the WAN via the router.
Go to ConfigNetworkUPnP:
Select “Enable UPNP” and then input friendly name.
After you enable it and set the UPnP name, you will see the UPnP name by clicking “Network”
on the desktop of your computer which is in the same local area network. Then double click this
name to access the camera quickly.
4.4.8 Mail configuration
If you need to trigger E-mail when an alarm happens or IP address is changed, please set the
E-mail here first.
Go to ConfigNetwork Email.
21
Network Camera User Manual
Sender Address: sender’s e-mail address;
User name and password: sender’s user name and password;
SMTP Address: The SMTP IP address or host name.
Select the secure connection type at the Secure Connection pull down list according to user’
actual needs;
SMTP Port: The SMTP port.
Send Intervals: Set it as needed.
Click “Test Account Setting” to test the effectiveness of the account.
Receiver email address: receiver’s e-mail address;
4.4.9 FTP Setting
After you set the FTP server, the captured pictures on an alarm will be uploaded to the FTP
server.
Go to ConfigNetwork FTP.
22
Network Camera User Manual
To Add FTP
Server Name：The name of the FTP.
Server Address: The IP address or domain name of the FTP.
Upload Path: The path of uploading the files.
Port: The port of the FTP.
Use Name and Password: The username and password are used to login the FTP.
4.5 Security Configuration
4.5.1 User Configuration
Go to ConfigSecurity.
Add user:
1. Click “Add” button to pop up the following textbox.
23
Network Camera User Manual
2. Input user name in “User Name” textbox.
3. Input letters or numbers in “Password” and “Confirm Password” textbox.
4. Choose the use type.
5. Input the MAC address of the PC in “Binding MAC address” textbox.
After binding physical address to the IP-CAM, you can access the device on this PC only. If the
MAC address was “00:00:00:00:00:00” which means it can be connected to any computers.
6. Click “OK” button and then the new added user will display in the user list.
Modify user:
1. Select the user you need to modify password and physical address in the user configuration
list box.
2. The “Edit user” dialog box pops up by clicking “Modify” button.
3. Input old password of this user in the “Password” text box.
4. Input new password in the “New password” and “Confirm Password” text box.
5. Input computer’s MAC address as required.
6. Click “OK” button to modify user’s password.
Delete user:
1. Select the user you want to delete in the user configuration list box.
2. Click “Delete” button to delete the user.
24
Network Camera User Manual
Note: The default super administrator cannot be deleted.
4.5.2 Online Video User
Go to ConfigSecurityOnline Video User. You can view the user who is viewing the live
video.
4.5.3 Block and Allow List
Go to ConfigSecurityBlock and Allow Lists.
Setting steps are as follows:
Check “Enable IP address filtering” check box.
Select “Block the following IP address”, input IP address in the IP address list box and click
“Add” button. The operation step of “Allow the following IP address” and MAC address filter
settings are the same with “Block the following IP address”.
After you set the IP address or MAC address, the system will block or allow the user using the
added IP address or MAC address to access the camera.
4.6 Maintenance
4.6.1 Backup & Restore
Go to ConfigMaintenanceBackup & Restore.
25
Network Camera User Manual
Import & Export Setting:
You can import or export the setting information from PC or to device.
1. Click “Browse” to select save path for import or export information on PC.
2. Click “Import Setting” or “Export Setting” button.
Default Setting
Click “Load default” button to restore all system settings to default status.
4.6.2 Reboot Device
Go to ConfigMaintenanceReboot.
Click “Reboot” button to reboot the device.
4.6.3 Upgrade
Go to ConfigMaintenanceUpgrade. In this interface, you can upgrade the system.
1. Click “Browse” button to select the save path of the upgrade file
2. Click “Upgrade” button to start upgrading the application program.
3. The device will restart automatically
4. After you successfully update the software, click “OK” button to close IE and then re-open
IE to connect IP-Cam.
Caution! You can’t disconnect to PC or close the IP-CAM during upgrade.
26
Network Camera User Manual
4.6.4 Log
To query and export log
1. Go to ConfigMaintenanceOperation Log.
2. Select the main type, sub type, start and end time.
3. Click “Query” to view the operation log.
4. Click “Export” to export the operation log.
You can export and view the run log by clicking ConfigMaintenanceRun Log.
27
Network Camera User Manual
Button
Description
Play button. After pausing the video, click this button to
continue playing.
Pause button.
Stop button.
Speed down.
Speed up.
Open/close watermark.
Full screen. Click it to display full screen. Double click to exit
full screen.
5 Search
You can play the local video record through search interface. Before playing, please set the
storage path of the video record in the local configuration interface and make sure there are
record files. After that, click “Search” tab on the menu toolbar. The following interface will be
seen.
Choose the date and the start time and end time and then click “Search” button to search the
record files. Double click the record file to play the record.
The descriptions of the buttons on the playback interface are as follows.
28
Network Camera User Manual
Appendix
Appendix 1 Q & A
Q: How to find my password if I forget it?
A：Reset the device to the default factory settings.
Default IP: 192.168.226.201
User name: admin
Password: 123456
Q: Fail to connect devices through IE browser, why?
A: Network is not well connected. Please check the connection and make sure it is connected
well.
B: IP is not available. Reset the valid IP.
C: Web port number has been revised: contact administrator to get the correct port number.
D: Exclude the above reasons. Recover default setting by IP-Tool.
Note: Default IP: 192.168.226.201，mask number: 255.255.255.0
Q：IP tool cannot search devices, why?
A：It may be caused by the anti-virus software in your computer. Please exit it and try to
search device again.
Q：IE cannot download ActiveX control. How can I do?
a. IE browser blocks ActiveX. Please try as below.
① Open IE browser. Click Tools-----Internet Options….
② Select Security------Custom Level….
③ Enable all the sub options under “ActiveX controls and plug-ins”.
29
Network Camera User Manual
④ Then click OK to finish setup.
b. Other plug-ins or anti-virus blocks ActiveX. Please uninstall or close them.
30
Network Camera User Manual
Specification /Model
20m IR Water-proof Bullet
Network Camera
20m IR Water-proof
Bullet Network Camera
Camera
Image Sensor
1/3＂CMOS
Image Size
2048×1536
Electronic Shutter
1/25s~1/100000s
Auto Iris
Fixed Iris
Min. llumination
0.07lux@F1.2, AGC ON; 0 lux with IR
Lens
3.6mm@F2.0, angle of view: 70°; (2.8mm optional)
Lens Mount
M12
Day&Night
ICR
WDR
Digital WDR
Digital NR
3D DNR
Angle Adjustment
Any angle
Image
Video Compression
H.264/MJPEG
H.264 Type
Baseline profile/main profile/high profile
Video Bit Rate
128Kbps~6Mbps
Resolution
3MP (2048×1536),1080P, 720P, D1, CIF, 480×240
Main Stream
60Hz: 3MP(1~20fps)/1080P (1~30fps)/1280×720(1~30fps)
50Hz: 3MP(1~20fps)/1080P (1~25fps)/ 1280×720(1~25fps)
Image Settings
Saturation, Brightness, Chroma, Contrast, Wide Dynamic, Sharpen, NR, etc. adjustable
through client or web browser
ROI
Support
Interfaces
Network
RJ45
Fucntion
Remote Monitoring
IE browser, CMS remote control
Online Connection
Support simultaneous monitoring for up to 4 users and multi-stream transmission
Network Protocol
TCP/IP, UDP, DHCP, NTP, RTSP, PPPoE, DDNS, SMTP, FTP
Interface Protocol
ONVIF
Storge
Network remote storage
Smart Alarm
Motion alarm
Others
IR Distance
10~20 m
Protection Grade
IP66
Power
DC12V / PoE
Power Consumption
< 2W(ICR OFF); <4.5W(ICR ON)
Opterating
Environment
Temperature: -20°C~50°C; Humidity: 10%~90%
Dimension (mm)
Ø64mm×183mm
Ø70mm×156mm
Weight（net）
337g
364g
Installation
Wall mounting; pendent mounting
Appendix 2 Specifications
31
Network Camera User Manual
Specification /Model
30m IR Water-proof Bullet Network Camera
Camera
Image Sensor
1/3＂CMOS
Image Size
2048×1536
Electronic Shutter
1/25s~1/100000s
Auto Iris
Fixed Iris
Min. llumination
0.07lux@F1.2, AGC ON: 0 lux with IR
Lens
3.6mm@F2.0, angle of view: 70°; (2.8mm,
6mm optional)
2.8~12mm@F1.4, angle of view: 84°~ 27°
Lens Mount
M12
Ø14
Day&Night
ICR
WDR
Digital WDR
Digital NR
3D DNR
Angle Adjustment
Any angle
Image
Video Compression
H.264/MJPEG
H.264 Type
Baseline profile/main profile/high profile
Video Bit Rate
128Kbps~6Mbps
Resolution
3MP (2048×1536),1080P, 720P, D1, CIF, 480×240
Main Stream
60Hz: 3MP(1~20fps)/1080P (1~30fps)/1280×720(1~30fps)
50Hz: 3MP(1~20fps)/1080P (1~25fps)/ 1280×720(1~25fps)
Image Settings
Saturation, Brightness, Chroma, Contrast, Wide Dynamic, Sharpen, NR, etc. adjustable
through client or web browser
ROI
Support
Interfaces
Network
RJ45
Fucntion
Remote Monitoring
IE browser, CMS remote control
Online Connection
Support simultaneous monitoring for up to 4 users and multi-stream transmission
Network Protocol
TCP/IP, UDP, DHCP, NTP, RTSP, PPPoE, DDNS, SMTP, FTP
Interface Protocol
ONVIF
Storge
Network remote storage
Smart Alarm
Motion alarm
Others
IR Distance
20~30 m
Protection Grade
IP66
Power
DC12V/PoE
Power Consumption
< 2W(ICR OFF); < 5.5W(ICR ON)
Opterating
Environment
Temperature: -20°C~50°C; Humidity: 10%~90%
Dimension (mm)
Ø87mm×219mm
Weight（net）
636g
Installation
Wall mounting; pendent mounting
32
Network Camera User Manual
Specification /Model
50m IR Water-proof Bullet Network Camera
Camera
Image Sensor
1/3＂CMOS
Image Size
2048×1536
Electronic Shutter
1/25s~1/100000s
Auto Iris
Fixed Iris
Min. llumination
0.07lux@F1.2, AGC ON: 0 lux with IR
Lens
2.8~12mm@F1.4, angle of view: 84°~ 27°
Lens Mount
Ø14
Day&Night
ICR
WDR
Digital WDR
Digital NR
3D DNR
Angle Adjustment
Any angle
Image
Video Compression
H.264/MJPEG
H.264 Type
Baseline profile/main profile/high profile
Video Bit Rate
128Kbps~6Mbps
Resolution
3MP (2048×1536),1080P, 720P, D1, CIF, 480×240
Main Stream
60Hz: 3MP(1~20fps)/1080P (1~30fps)/1280×720(1~30fps)
50Hz: 3MP(1~20fps)/1080P (1~25fps)/ 1280×720(1~25fps)
Image Settings
Saturation, Brightness, Chroma, Contrast, Wide Dynamic, Sharpen, NR, etc. adjustable
through client or web browser
ROI
Support
Interfaces
Network
RJ45
Fucntion
Remote Monitoring
IE browser, CMS remote control
Online Connection
Support simultaneous monitoring for up to 4 users and multi-stream transmission
Network Protocol
TCP/IP, UDP, DHCP, NTP, RTSP, PPPoE, DDNS, SMTP, FTP
Interface Protocol
ONVIF
Storge
Network remote storage
Smart Alarm
Motion alarm
Others
IR Distance
30~50 m
Protection Grade
IP66
Power
DC12V/PoE
Power Consumption
< 2W(ICR OFF); < 6.5W(ICR ON)
Opterating
Environment
Temperature: -20°C~50°C; Humidity: 10%~90%
Dimension (mm)
Ø109mm×284mm
Weight（net）
1100g
Installation
Wall mounting; pendent mounting
33
Network Camera User Manual
Specification /Model
30m IR Water-proof
Bullet Network Camera
50m IR Water-proof
Bullet Network Camera
Camera
Image Sensor
1/3＂CMOS
Image Size
2048×1536
Electronic Shutter
1/25s~1/100000s
Auto Iris
Fixed Iris
Min. llumination
0.07lux@F1.2, AGC ON: 0 lux with IR
Lens
6mm@F1.6, angle of view: 43° (3.6mm, 8mm optional)
Lens Mount
M12
Day&Night
ICR
WDR
Digital WDR
Digital NR
3D DNR
Angle Adjustment
Any angle
Image
Video Compression
H.264/MJPEG
H.264 Type
Baseline profile/main profile/high profile
Video Bit Rate
128Kbps~6Mbps
Resolution
3MP (2048×1536),1080P, 720P, D1, CIF, 480×240
Main Stream
60Hz: 3MP(1~20fps)/1080P (1~30fps)/1280×720(1~30fps)
50Hz: 3MP(1~20fps)/1080P (1~25fps)/ 1280×720(1~25fps)
Image Settings
Saturation, Brightness, Chroma, Contrast, Wide Dynamic, Sharpen, NR, etc. adjustable
through client or web browser
ROI
Support
Interfaces
Network
RJ45
Fucntion
Remote Monitoring
IE browser, CMS remote control
Online Connection
Support simultaneous monitoring for up to 4 users and multi-stream transmission
Network Protocol
TCP/IP, UDP, DHCP, NTP, RTSP, PPPoE, DDNS, SMTP, FTP
Interface Protocol
ONVIF
Storge
Network remote storage
Smart Alarm
Motion alarm
Others
IR Distance
20~30 m
30~50 m
Protection Grade
IP66
Power
DC12V
Power Consumption
< 2W(ICR OFF); < 3.5W(ICR ON)
< 2W(ICR OFF); < 5W(ICR ON)
Opterating
Environment
Temperature: -20°C~50°C; Humidity: 10%~90%
Dimension (mm)
99×188×86 (W×D×H)
Weight（net）
488g
Installation
Wall mounting
34
Network Camera User Manual
Specification /Model
20m IR Water-proof Dome Network Camera
Camera
Image Sensor
1/3＂CMOS
Image Size
2048×1536
Electronic Shutter
1/25s~1/100000s
Auto Iris
Fixed Iris
Min. llumination
0.07lux@F1.2, AGC ON: 0 lux with IR
Lens
3.6mm@F2.0, angle of view: 70°; (2.8mm optional)
Lens Mount
M12
Day&Night
ICR
WDR
Digital WDR
Digital NR
3D DNR
Angle Adjustment
Pan：0°~240°；Tilt: 0°~68°；Rotation：0°~220°
Image
Video Compression
H.264/MJPEG
H.264 Type
Baseline profile/main profile/high profile
Video Bit Rate
128Kbps~6Mbps
Resolution
3MP (2048×1536),1080P, 720P, D1, CIF, 480×240
Main Stream
60Hz: 3MP(1~20fps)/1080P (1~30fps)/1280×720(1~30fps)
50Hz: 3MP(1~20fps)/1080P (1~25fps)/ 1280×720(1~25fps)
Image Settings
Saturation, Brightness, Chroma, Contrast, Wide Dynamic, Sharpen, NR, etc. adjustable
through client or web browser
ROI
Support
Interfaces
Network
RJ45
Fucntion
Remote Monitoring
IE browser, CMS remote control
Online Connection
Support simultaneous monitoring for up to 4 users and multi-stream transmission
Network Protocol
TCP/IP, UDP, DHCP, NTP, RTSP, PPPoE, DDNS, SMTP, FTP
Interface Protocol
ONVIF
Storge
Network remote storage
Smart Alarm
Motion alarm
Others
IR Distance
10~20 m
Protection Grade
IP66&IK10
Power
DC12V（PoE power supply optional）
Power
Consumption
< 2.5W(ICR OFF); <4.5W(ICR ON)
Opterating
Environment
Temperature: -20°C~50°C; Humidity: 10%~90%
Dimension (mm)
Ø116mm×91mm
Weight（net）
318g
Installation
Pendent mounting (wall mounting available with junction box and bracket)
35
Network Camera User Manual
Specification /Model
30m IR Water-proof Dome Network Camera
Camera
Image Sensor
1/3＂CMOS
Image Size
2048×1536
Electronic Shutter
1/25s~1/100000s
Auto Iris
Fixed Iris
Min. llumination
0.07lux@F1.2, AGC ON: 0 lux with IR
Lens
2.8~12mm@F1.4, angle of view: 84°~ 27°
Lens Mount
Ø14
Day&Night
ICR
WDR
Digital WDR
Digital NR
3D DNR
Angle Adjustment
Pan：0°~360°； Tilt：0°~77°；Rotation：0°~360°
Image
Video Compression
H.264/MJPEG
H.264 Type
Baseline profile/main profile/high profile
Video Bit Rate
128Kbps~6Mbps
Resolution
3MP (2048×1536),1080P, 720P, D1, CIF, 480×240
Main Stream
60Hz: 3MP(1~20fps)/1080P (1~30fps)/1280×720(1~30fps)
50Hz: 3MP(1~20fps)/1080P (1~25fps)/ 1280×720(1~25fps)
Image Settings
Saturation, Brightness, Chroma, Contrast, Wide Dynamic, Sharpen, NR, etc. adjustable
through client or web browser
ROI
Support
Interface
s
Network
RJ45
Fucntion
Remote Monitoring
IE browser, CMS remote control
Online Connection
Support simultaneous monitoring for up to 4 users and multi-stream transmission
Network Protocol
TCP/IP, UDP, DHCP, NTP, RTSP, PPPoE, DDNS, SMTP, FTP
Interface Protocol
ONVIF
Storge
Network remote storage
Smart Alarm
Motion alarm
Others
IR Distance
20~30 m
Protection Grade
IP66&IK10
Power
DC12V（PoE power supply optional）
Power
Consumption
< 2.5W(ICR OFF); <4.5W(ICR ON)
Opterating
Environment
Temperature: -20°C~50°C; Humidity: 10%~90%
Dimension (mm)
Ø150mm×114mm
Weight（net）
927g
Installation
Pendent mounting (wall mounting available with junction box and bracket)
36
Network Camera User Manual
Specification /Model
20m IR Water-proof Dome
Network Camera
20m IR Water-proof Dome
Network Camera
Camera
Image Sensor
1/3＂CMOS
Image Size
2048×1536
Electronic Shutter
1/25s~1/100000s
Auto Iris
Fixed Iris
Min. llumination
0.07lux@F1.2, AGC ON: 0 lux with IR
Lens
3.6mm@F2.0, angle of view: 70°; (2.8mm optional)
Lens Mount
M12
Day&Night
ICR
WDR
Digital WDR
Digital NR
3D DNR
Angle Adjustment
Any angle
Image
Video Compression
H.264/MJPEG
H.264 Type
Baseline profile/main profile/high profile
Video Bit Rate
128Kbps~6Mbps
Resolution
3MP (2048×1536),1080P, 720P, D1, CIF, 480×240
Main Stream
60Hz: 3MP(1~20fps)/1080P (1~30fps)/1280×720(1~30fps)
50Hz: 3MP(1~20fps)/1080P (1~25fps)/ 1280×720(1~25fps)
Image Settings
Saturation, Brightness, Chroma, Contrast, Wide Dynamic, Sharpen, NR, etc. adjustable
through client or web browser
ROI
Support
Interfaces
Network
RJ45
Fucntion
Remote Monitoring
IE browser, CMS remote control
Online Connection
Support simultaneous monitoring for up to 4 users and multi-stream transmission
Network Protocol
TCP/IP, UDP, DHCP, NTP, RTSP, PPPoE, DDNS, SMTP, FTP
Interface Protocol
ONVIF
Storge
Network remote storage
Smart Alarm
Motion alarm
Others
IR Distance
10~20 m
Protection Grade
IP66
Power
DC12V（PoE power supply optional）
Power Consumption
< 2W(ICR OFF); <4W(ICR ON)
Opterating
Environment
Temperature: -20°C~50°C; Humidity: 10%~90%
Dimension (mm)
Ø87mm×108mm
Ø84.3mm×94.6mm
Weight（net）
400g
428g
Installation
Pendent mounting (wall mounting available with junction box and bracket)
37
Network Camera User Manual
Specification /Model
30m IR Water-proof Dome
Network Camera
30m IR Water-proof Dome
Network Camera
Camera
Image Sensor
1/3＂CMOS
Image Size
2048×1536
Electronic Shutter
1/25s~1/100000s
Auto Iris
Fixed Iris
Min. llumination
0.07lux@F1.2, AGC ON: 0 lux with IR
Lens
2.8~12mm@F1.4, angle of view: 84°~ 27°
Lens Mount
Ø14
Day&Night
ICR
WDR
Digital WDR
Digital NR
3D DNR
Angle Adjustment
Any angle
Image
Video
Compression
H.264/MJPEG
H.264 Type
Baseline profile/main profile/high profile
Video Bit Rate
128Kbps~6Mbps
Resolution
3MP (2048×1536),1080P, 720P, D1, CIF, 480×240
Main Stream
60Hz: 3MP(1~20fps)/1080P (1~30fps)/1280×720(1~30fps)
50Hz: 3MP(1~20fps)/1080P (1~25fps)/ 1280×720(1~25fps)
Image Settings
Saturation, Brightness, Chroma, Contrast, Wide Dynamic, Sharpen, NR, etc. adjustable
through client or web browser
ROI
Support
Interfaces
Network
RJ45
Fucntio
n
Remote
Monitoring
IE browser, CMS remote control
Online Connection
Support simultaneous monitoring for up to 4 users and multi-stream transmission
Network Protocol
TCP/IP, UDP, DHCP, NTP, RTSP, PPPoE, DDNS, SMTP, FTP
Interface Protocol
ONVIF
Storge
Network remote storage
Smart Alarm
Motion alarm
Others
IR Distance
20~30 m
Protection Grade
IP66
Power
DC12V/PoE
Power Consumption
< 2W(ICR OFF); <4.5W(ICR ON)
Opterating
Environment
Temperature: -20°C~50°C; Humidity: 10%~90%
Dimension (mm)
Ø109mm×130mm
Ø120.4mm×102.5mm
Weight（net）
688g
723g
Installation
Pendent mounting (wall mounting available with junction box and bracket)
38
A2
Loading...