15-DVR16SAE-LAN
15-DVR16SAE-LAN
ALL ABOUT IMAGE RECOGNITION & PROCESSING
The most stable and reliable real stand-alone Digital Video Recorder
User Manual
VER 1.0
Safety & Security
16 Channel Digital Video Recorder
1
Chapter 1 . Product package
Chapter 2. Installation procedure
Table of Contents
1-1. The contents of package
3
1-2. Name and function of each button (front panel)
4
1-3. Name and function of each button (Rear panel)
5
2-1. Camera connection
6
2-2. Monitor connection (Composite monitor)
6
2-3. Monitor connection (S-VHS)
7
2-4. VCR & VIDEO printer connection
7
2-5. Sensor connection
8
2-6. Network connection
8
2-7. HDD connection
9
2-8. Power connection
9
Chapter 3. Operation
3-1. Basic Display
10
3-2. DVR SYSTEM Log-in
11
3-3. Recording 12
3-4. Playback
15
3-5. Set-up
17
1. Basic operation
17
2. CAMERA SETUP
18
3. ADJUST COLOR
18
4. MOTION SETUP
19
5. SET/TIME DATE
20
6. RECORD SETUP
20
7. HDD MANAGEMENT
21
8. MISCELLANEOUS SETUP
24
Chap 4. Specification and Configuration
4-1. SPECIFICATIONS
25
4-2. Configuration 15-DVR16SAE-LAN
26
4-3. RS-232C Hex-code table
26
4-4. Arrange of RS 485 and RS-232C pin
26
26
2. Configuration of 15-DVR16SAE-LAN
3. RS-232C ASCII-code table
Following ASCII-code are for programmers who want to control DVR unit via RS-232C port.
RS-232C specification (baud rate/parity/data length/stop bit) : 57600, N, 8, 1
1 Byte ASCII-code
MODE
FRZ
SEQ
ZOOM
D
F
Q
Z
PIP
P/T
I
T
R
S
<
P
>
A
CH1
CH2
CH3
CH4
1
2
3
4
CH5
CH6
CH7
CH8
5
6
7
8
CH9
CH10
CH11
CH12
9
0
!
@
CH13
CH14
CH15
CH16
#
$
%
^
MENU
ENTER
LEFT
RIGHT
M
H
K
UP
DN
U
J
4. Configuration
4. Arrangement of RS 485 and RS-232C pin
9. TCP/IP SETUP
10. FACTORY DEFAULT
24
21
Comm Port
RS-232C
1 5
6 9
Pin No. Definition
1 NC
2 RxD
3 TxD
4 SD-(RS 485)
5 GND
6 SD+(RS 485)
7 NC
8 NC
9 NC
15-DVR16SAE-LAN15-DVR16SAE-LAN
ALL ABOUT IMAGE RECOGNITION & PROCESSING ALL ABOUT IMAGE RECOGNITIO N & PROCESSING
1. This document is intended for both the administrator and users of 15-DVR16SAE-LAN model.
2. This manual contains information for configuring, managing and using 15-DVR16SAE-LAN model.
4. To prevent fire or electrical shock, do not expose the product to heat or moisture.
3. Be sure to read through this manual before using this 15-DVR16SAE-LAN model.
2
5. Check electricity at the place you want to install the DVR unit if it is stable and meets our electricity
requirements. Unstable electricity will cause malfunction of the unit or give critical damage to
the unit.
6. Several chips on the main board of the DVR unit and hard disk drive inside the unit generate
heat, and it must be properly discharged.
Do not put any objects just beside exhaust port (fan) on the left side of the unit and do not close
up an opening (fresh air in-take) on the right side of the unit.
7. Put the DVR unit at well-ventilated place and do not put heat-generating objects on the unit.
When it is installed inside 19 inch mounting rack together with other devices, please check built in ventilation fan of the rack is properly running.
Before installing 15-DVR16SAE-LAN, be sure to thoroughly review and follow the instructions in this
User’s Manual. Pay particular attention to the parts that are marked NOTICE.
Also, when connecting with external application, first turn the power OFF and follow manual instruction for
8. For questions and technical assistance of this product, contact your local dealer.
appropriate installation.
25
1. SPECIFICATIONS
INPUT
OUTPUT
S/N RATIO
HORIZONTAL RESOLUTION
COLOR
DIGITAL ZOOM
PICTURE IN PICTURE
SEQUENCE
DIAPLAY QUALITY
RECORDING FRAME RATE
HDD STORAGE CAPACITY
COMPRESSED
RECORDING MODE
PLAY BACK
SPLIT SCREEN
BACK-UP
ALARM I/O
CAMERA CONTROL
16 CH INPUT 1.0 Vp-p, 75 Ohm UNBALANCED (BNC TYPE)
3 OUTPUT ( BNC-MONITOR / BNC-VCR / S-VHS )
MORE THAN 46 dB
480 TV LINES
16.7 MILLION
LIVE & PLAYBACK
YES
YES
FULL : 720(H)X480(V) ACTIVE PIXELS
SPLIT :180(H)X120(V) ACTIVE PIXELS
30 fps
HDD *2
JPEG
REAL-TIME/ TIME-LAPSE / EVENT/ MOTION
SEARCH, STILL
SINGLE-FULL, QUAD, 9 SPLIT , 16 SPLIT
15-DVR16SAE-LAN
CONVENTIONAL VCR, TIME LAPSE VCR (VCR OUTPUT PROVIDED)
REMOTE BACK-UP USING TCP/IP
16 ALARM INPUT ,1 RELAY OUTPUT
PAN/TILT/ZOOM AND FOCUS
VIDEO
MONITORING
RECORDING
/
PLAY BACK
FUNCTION
OTHERS
MODEL NO
OPERATION TEMPERATURE
OPERATION HUMIDITY
IR REMOTE
DIMENSION
WEIGHT
POWER SUPPLY
41F~ 104F (5C~ +40C)
LESS THAN 90%
BUILT-IN
44 X 434 X 360 mm
APPROX. 4.5KG (HDD 1EA)
DC ADAPTER ( 12V DC 4.5A)
MECHANICAL
Chapter 4 . Specification and configuration
4. Configuration
HDD EXPANSION
OPTIONAL HDD BAY SUPPORTED
MAX 20 HDD EXPANDABLE
COMPATIBILITY WITH DIFFERENT MANUFACTURER OF HDD
WEB INTERFACE TCP/IP WITH CLIENT SOFTWARE
15-DVR16SAE-LAN15-DVR16SAE-LAN
ALL ABOUT IMAGE RECOGNITION & PROCESSING ALL ABOUT IMAGE RECOGNITIO N & PROCESSING
Before reading this manual
About this manual
1. Product package
Chapter 1 . Product Packag e
1-1. The contents of package
1. 16 ch 15-DVR16SAE-LAN unit
5. Accessories (Rack mount bracket and bolts)
Mounting bracket and bolts necessary for fixing DVR unit into 19 inch rack, and batteries for remote controller.
Record data of pictures from camera on hard disk drive, after converting it into digital data.
Describe how to install and operate this DVR unit.
4. DC power adapter and power cable
Convert AC 110V or AC 220V into DC 12V to supply to DVR unit.
3. Remote controller
IR remote controller enables to operate DVR unit apart from the unit.
3
24
Display of PASSWORD SETUP
CURRENT PASSWORD
NEW PASSWORD
CONFIRM PASSWORD
: _ _ _ _ _ _ _ _
: _ _ _ _ _ _ _ _
: _ _ _ _ _ _ _ _
Current password
New password
New password to confirm
f. PASSWORD SETUP.
INPUT YOUR OWN PASSWORD,
THEN PRESS [ENTER]
TO EXIT, PRESS [MENU]
To input user’s own password in the first operation or to change password.
Move using [Up] and [Down] buttons and input your own password by pressing any buttons on the front of DVR
unit. Length of password is from 1 to 8. To change password, first input current password and then new
password. You have to input new password again to confirm.
Notice : Password set by manufacturer before delivery (FACTORY DEFAULT) is null, and just press [MENU] and
then press [ENTER] to enter into SETUP menu.
Notice : In the first operation, we recommend you to set own password.
In case you forgot own password, contact dealer to know how to get into SETUP menu.
SYSTEM SETUP
CAMERA SETUP
TIME/DATE SETUP
RECORD SETUP
HDD MANAGEMENT
MISCELLANEOUS SET U P
TCP/IP SETUP
FACTORY DEFAULT
BUZZER SETUP
ALARM SETUP
TIMER SETUP
PAN/TILT CMD SETUP
BAUDRATE SETUP
PASSWORD SETUP
Display of FACTORY SETUP
FACTORY SETUP
ALL SETUP
CAMERA COLOR
CAMERA TITLE
MOTION MASK
PAN/TILT COMMAND
SYSTEM STATUS
SYSTEM SETUP
CAMERA SETUP
TIME/DATE SETUP
RECORD SETUP
HDD MANAGEMENT
MISCELLANEOUS SET U P
TCP/IP SETUP
FACTORY DEFAULT
--NO
NO
NO
NO
NO
RUN
You can set all groups of settings as a whole or set them group by group. Move to menu items using [Up] and
[Down] buttons and select “YES” or “NO”, and then move to “RUN”. Press [ENTER] button to set at
FACTORY DEFAULT for selected group of settings.
Notice : When you connect or replace new HDD, set at FACTORY DEFAULT before starting to record.
3. Operation
2. User manual for 16 ch DVR
SELECT , EDIT ENTER
10. FACTORY DEFAULT
Initialize system setup as settings recommended by manufacturer (FACTORY DEFAULT).
9. TCP/IP SETUP
In case TCP/IP option is included, you have to input IP address, Port number, Subnet Mask and Gateway into
TCP/IP SETUP of DVR unit. If DVR Unit is connected to leased line with static IP, ADSL with static IP or
dynamic IP, or cable modem with dynamic IP, you can access to DVR unit via Internet line to see live pictures or
search recorded pictures, far apart from DVR unit. In case both DVR unit and client PC are connected to the
same LAN network (Intranet), you can access to DVR unit from the client PC, but somebody outside Intranet can
not access to DVR unit via Internet line. In all cases, you have to install client program (Remote Viewer) on the
client PC from which you want to access to DVR unit. For more details, refer to Remote viewer manual for 16 ch
DVR included in the package.
MODE
FRZ
SEQ ZOOM PIP P/T
POWER
OVERWRITE
RECORD
PLAY
SETUP
123 4 5 6
9 10 111213 14
7
15
MENU
ENTER
8
16
CAMERA
15-DVR16SAE-LAN15-DVR16SAE-LAN
ALL ABOUT IMAGE RECOGNITION & PROCESSING ALL ABOUT IMAGE RECOGNITIO N & PROCESSING
User Manual
Safety & S ecurit y
BUZZER SETUP
ALARM SETUP
TIMER SETUP
PAN/TILT CMD SETUP
BAUDRATE SETUP
PASSWORD SETUP
d. PAN/TILT CMD SETUP.
User must select commands needed for PTZ cameras (from 1st to 4th DEV), and input LEN and protocol
(Hexa-code). For commands not used for your PTZ cameras, LEN value must be set at 0.
Commands whose LEN are 0 are not shown when you practically control PTZ camera later.
Using [Up] and [Down] buttons, move to item you want to select or set, and use [Left] and [Right] buttons to
set values.
You can input protocol using numerical buttons on the front of DVR unit or remote controller.
Following table shows buttons corresponding to each HEX-code for protocol.
HEX-code 1 2 3 4 5 6 7 8 9 A B C D E F 0
Button on the front 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Button on remote controller 1 2 3 4 5 6 7 8 9 0,0 0,1 0,2 0,3 0,4 0,5 0,6
Input protocol of PTZ camera or speed dome camera which shall be controlled by data communication
via RS-485. Max. length of protocol for each command is 15 Byte, and Baud rate is settable from 1200 to 19200.
Max. 4 PTZ cameras can be connected to DVR unit.
SYSTEM SETUP
CAMERA SETUP
TIME/DATE SETUP
RECORD SETUP
HDD MANAGEMENT
MISCELLANEOUS SETUP
TCP/IP SETUP
FACTORY DEFAULT
- Setting sequence
- How to input protocol
1. DEV : From 1st to 4th.
2. Select command
3. Set Byte of command : max. 15. Byte of commands not used for each device must be set at 0.
4. Input protocol of selected command
5. Repeat process from 1 to 4 until you complete to input protocol for all commands you need.
* Use [Record] button to copy and [Playback] button to paste, in case there are many protocols
similar to each other.
3. Operation
23
1. POWER SWITCH WITH LED : DC power on-off switch with built-in LED
16. MENU: Used to change menu in SYSTEM SETUP
17. ENTER: Used as selection key in SYSTEM SETUP or changes contents displayed in live display.
By pressing this button repeatedly in live display mode, contents of display, that are, time and date,
DVR status, and camera title, is included or excluded, and you can select any one of 8 choices.
3. MODE: Press [MODE] button and [1], [2], or [3] to change to 4-split, 9-split, or 16-split screen, respectively.
8. P/T : Enter into or exit from PAN/TILT CONTROL mode
15. Camera No : Represents camera numbers. Used with MODE button or to enter numbers.
7. PIP : In full screen, this button creates PIP( Picture In Picture ) in rotation.
4. FRZ : On-off switch to freeze pictures in live mode
5. SEQ : In full screen, this button shows pictures in rotation.
6. ZOOM: In full screen, this button enlarges pictures two times ( Possible to fix area to be enlarged using
direction buttons.)
18. IR receiver : If blocked up by any object, remote controller does not work.
19. Direction key : Used to move in SETUP menu, or to change values
4
Notice : If several keys are pressed at the same time, or improper sequence in pressing
buttons may cause malfunction of DVR unit.
2. LED : Indicates the status of system
9. Record ( ): Records picture data on hard disk drive
10. Stop( ): Stops recording or playback
11. Fast backward ( ) : High speed playback in reverse direction in playback mode, or moving to the
start of recorded data when it is in stop mode
12. Playback( ) : Playback when it is pressed shortly in stop mode, or playback in reverse direction
when it is pressed in playback mode.
Enter into GO TO menu in case pressed in longer time in stop mode.
13. Fast Forward ( ): High speed playback in forward direction in playback mode, or moving to the last
of recorded data when it is in stop mode.
14. Pause( ): Pauses when it is in playback mode
1. Unit Description
[ Front Panel ]
1-2. Name and function of each button
e. BAUDRATE SETUP
SYSTEM SETUP
CAMERA SETUP
TIME/DATE SETUP
RECORD SETUP
HDD MANAGEMENT
MISCELLANEOUS SET U P
TCP/IP SETUP
FACTORY DEFAULT
BUZZER SETUP
ALARM SETUP
TIMER SETUP
PAN/TILT CMD SETUP
BAUDRATE SETUP
PASSWORD SETUP
PAN/TILT CMD STEUP
NO_ _
01
02
03
04
05
06
07
08
HEXA_ _ _ _
00
00
00
00
00
00
00
00
_ _
:
:
:
:
:
:
:
:
NO_ _
09
10
11
12
13
14
15
HEXA_ _ _ _
00
00
00
00
00
00
00
_ _
:
:
:
:
:
:
:
DEV : 1 ST
CMD : POWER ON
LEN : 00 BYTE
COPY : REC PASTE : PLAY
Display of PAN/TILT CMD SETUP
Set baud-rate of PTZ camera to be connected.
(1200, 2400, 4800, 9600, and 19200 BPS)
If you connect DVR unit to your PC by 485 to 232 converter,
you can see data transmitted using program like Windows Hyper-terminal.
SELECT : THEN ENTER
1200 BPS
2400 BPS C URRENT RATE
4800 BPS 1200 BPS
9600 BPS
19200 BPS
CONFIRMATION VIA RS485 PORT
Display of BAUDRATE SETUP
BAUDRATE SETUP
SELECT : EDIT : NUMER IC/
If you press this button 2 times consecutively, it changes to screen position adjustment mode. In case
position of 16-split screen is not in the center of display unit, you can adjust screen position using [UP],
[DOWN], [LEFT], and [RIGHT] button. After adjustment, press [MODE] button once more to exit.
DEV represents device (model of PTZ camera).
We can connect up to 4 cameras with different protocols.
Note : For more details, refer to “How to incorporate PTZ protocol for 16ch DVR” included in the package.
11109
87654
3
1312
POWER
CAMERA
OVERWRITE
RECORD
PLAY
SETUP
1
14
15
2
16
17
18
19
ZOOM
SEQ PIP
MODE
FRZ P/T 1 87
6
5432
9 10111213 161514
MENU
ENTER
15-DVR16SAE-LAN15-DVR16SAE-LAN
ALL ABOUT IMAGE RECOGNITION & PROCESSING ALL ABOUT IMAGE RECOGNITIO N & PROCESSING
1
2
53
6 7
8
9
10
5
7. RS-232C/485 : Connect to external device of RS-232C or RS-485 protocol
(RS-232C : Control DVR using PC keyboard, RS-485 : PTZ camera control
Notice : When connect to other devices, make sure to turn off DC power switch on the front.
Notice : Improper DC power supply to DVR unit may cause damage to the system.
1. CH1 ~ CH16 : Connect cameras of NTSC or PAL system up to 16
2. CH1 ~ CH16 : Loop out from each camera from 1 to 16
3. VCR : Analog Backup output for VCR or video printer
4. MONITOR : Connect to composite monitor in NTSC or PAL system
5. S-VHS : Connect to S-VHS monitor for better quality of display
6. ALARM/ RELAY : Connect to alarm input and relay output
9. ETHERNET : Connect to Ethernet port for TCP/IP option
8. TERATRAY CONNECTION : Connect to HDD BAY for extension of HDD space
10. D/C 12V : Port for DC 12V, 4.5A
S-VHS
MONITOR
TERATRAY CONNECTION
DC 12V
CH1
CH8
CH7CH6
CH5
CH4
CH3
CH2
CH1 CH8
CH7CH6
CH5
CH4
CH3
CH2
CH9
CH16
CH15
CH14
CH13
CH12CH11
CH10
CH9
CH16CH15
CH14
CH13
CH12
CH11CH10
VCR
ETHERNET
LOOP
Comm Port
Comm Port
ALARM/ RELAY RS-232C/485
rks
4
[ Rear Panel ]
1-2. Name and function of each button
1. Unit Description
22
b. Set type of sensor (alarm)
Display of ALARM SETUP
ALARM SETUP
CH 01 : NO
CH 03 : NO
CH 05 : NO
CH 07 : NO
CH 09 : NO
CH 11 : NO
CH 13 : NO
CH 15 : NO
SELECT , EDIT ENTER/
CH 02: NO
CH 04 : NO
CH 06 : NO
CH 08 : NO
CH 10 : NO
CH 12 : NO
CH 14 : NO
CH 16 : NO
ALL : _ _
RELAY : ENABLE
NO
..NORMAL OPEN
NC
..NORMAL CLOSE
_ _..............DISABLE
SYSTEM SETUP
CAMERA SETUP
TIME/DATE SETUP
RECORD SETUP
HDD MANAGEMENT
MISCELLANEOUS SET U P
TCP/IP SETUP
FACTORY DEFAULT
BUZZER SETUP
ALARM SETUP
TIMER SETUP
PAN/TILT CMD SETUP
BAUDRATE SETUP
PASSWORD SETUP
Set type of alarm sensors connected to DVR unit. Set at NO (Normal Open) or NC (Normal Close) for alarm
sensors. Set at DISABLE or ENABLE for relay output.
Move to item you want to change using [Up] and [Down] buttons, change type using [Left] and [Right] button.
To set altogether as a whole, locate cursor at “ALL ; --“ and select type you want using [Left] and
[Right] button.
Just exit and all setting is memorized by the system.
c. Time Interval Setting
TIMER SETUP
FULL SCREEN
QUAD, 9SPLIT
PIP SCREEN
SELECT , EDIT ENTER/
SYSTEM SETUP
CAMERA SETUP
TIME/DATE SETUP
RECORD SETUP
HDD MANAGEMENT
MISCELLANEOUS SETUP
TCP/IP SETUP
FACTORY DEFAULT
BUZZER SETUP
ALARM SETUP
TIMER SETUP
PAN/TILT CMD SETUP
BAUDRATE SETUP
PASSWORD SETUP
: 1 SEC
: 3 SEC
: 2 SEC
Set time interval for SEQ, PIP (Picture in picture).
FULL SCREEN : Time interval of pictures rotating in channel sequence when [SEQ] button is pressed.
QUAD, 9 SPLIT : Time interval of pictures rotating in a certain sequence when [SEQ] button is pressed.
Pattern of rotation in quad rotation is 1/2/3/4, 5/6/7/8, 9/10/11/12, 13/14/15/16, 1/2/3/4, and so on.
Pattern of rotation in 9-split is 1/2/3/4/5/6/7/8/9, 1/2/10/11/12/13/14/15/16, 1/2/3/4/5/6/7/8/9, and so on.
PIP SCREEN : Time interval of small pictures rotating in sequence when [PIP] button is pressed.
3. Operation
Display of TIMER SETUP
15-DVR16SAE-LAN15-DVR16SAE-LAN
ALL ABOUT IMAGE RECOGNITION & PROCESSING ALL ABOUT IMAGE RECOGNITIO N & PROCESSING
2-1. Camera connection
Connect camera to the CAMERA INPUT (1~16 ) on the rear panel of unit.
2-2. Monitor connection (Composite monitor)
Connect the monitor to the MONITOR OUT on the rear panel of unit.
6
VIDEO
LENS
VIDEO
DC
AC24V/DC12
V.P
DC
LEVEL
Rear view of CAMERA
VIDEO A
IN OUT
VIDEO C
IN OUT
VIDEO B
IN OUT
CH1
CH16 VCR
CH1 CH16
MONITOR
LOOP
S-VHS
CH1
CH16 VCR
CH1 CH16
MONITOR
LOOP
S-VHS
2. Installation
Chapter 2. Procedure
7. HDD MANAGEMENT
21
a. Clear data stored on HDD.
When “HDD CLEAR [IN USE]” is displayed, press [ENTER] button and input password you already set.
If you entered correct password, HDD shall be cleared and “HDD CLEAR [EMPTY]” is displayed.
8. MISCELLANEOUS SETUP
SYSTEM SETUP
CAMERA SETUP
TIME/DATE SETUP
RECORD SETUP
HDD MANAGEMENT
MISCELLANEOUS SET U P
TCP/IP SETUP
FACTORY DEFAULT
BUZZER SETUP
ALARM SETUP
TIMER SETUP
PAN/TILT CMD SETUP
BAUDRATE SETUP
PASSWORD SETUP
Press [Up] and [Down] buttons to move to item you want to set, and select using [Left] and [Right] button.
Press [ENTER] button to set. To set altogether at ON or OFF, move to ALL BUZZER and set at ON or OFF.
a. BUZZER ON/OFF
BUZZER SETUP
ALL BUZZER
KEY BEEP
LOSS EVENT
ALARM EVENT
MOTION EVENT
: _ _ _
: ON
: OFF
: ON
: OFF
3. Operation
Display of BUZZER SETUP
Display of HDD MANAGEMENT
HDD MANAGEMENT
HDD CLEAR [IN USE]
HDD INFORMATION
HDD CLEAR
ENTER PASSWORD : _ _ _ _ _ _ _ _ _
INPUT YOUR OWN PASSWORD,
THEN PRESS [ENTER]
TO EXIT, PRESS [MENU]
HDD INFORMATION
DETECT
DRIVE
MODEL
SERIAL
SIZE
DRIVE
MODEL
SERIAL
SIZE
DRIVE
MODEL
SERIAL
SIZE
: 01/22 ( 61.47 Gbyte)
: 01
: IC35L0604VV407-0
: VNC302A3L2ZSWA
: 61.47 GByte
: 02
:
:
:
: 03
:
:
:
COPY : REC PASTE: PLAY
SELECT : ↑↓ EDIT : NUME RI C/←→
SYSTEM SETUP
CAMERA SETUP
TIME/DATE SETUP
RECORD SETUP
HDD MANAGEMENT
MISCELLANEOUS SETUP
TCP/IP SETUP
FACTORY DEFAULT
HDD CLEAR
HDD INFORMATION
b. Show information of HDDs installed inside DVR unit or HDD Bay.
SELECT , PRESS
ENTER
SELECT , EDIT ENTER/
For all buzzers
Button buzzer
Video loss buzzer
Alarm activated buzzer
Motion detected buzzer
Notice : This DVR system accepts camera with both PAL system or NTSC system, and
you are requested to set at PAL or NTSC system when you first boot, as per
specified in the procedure for selection of video system in 2-8 power connection.
Connect camera and monitor while DC power switch on the front panel is off.
15-DVR16SAE-LAN15-DVR16SAE-LAN
ALL ABOUT IMAGE RECOGNITION & PROCESSING ALL ABOUT IMAGE RECOGNITIO N & PROCESSING
CH1
CH16 VCR
CH1 CH16
MONITOR
LOOP
S-VHS
CH1
CH16 VCR
CH1 CH16
MONITOR
LOOP
S-VHS
2-3. Monitor (S-VHS) connection
Connect S-VIDEO monitor to MONITOR OUT (S-VHS) on the rear panel of unit.
2-4. VCR & VIDEO PRINTER Connection
Connect VCR or Video printer to VCR OUT on the rear panel of unit.
7
VIDEO A
IN O UT
VIDEO C
IN OUT
VIDEO B
IN OUT
VIDEO PRINTER
VCR
2. Installation
20
5. SET TIME/DATE
Sets Year/Month/Day/Hour/Minute/Second.
Using [Up] and [Down] buttons, move to menu item,
and change value using [Left] and [Right] buttons.
SET TIME/DATE
YEAR
MONTH
DAY
HOUR
MINUTE
SECOND
SELECT ↑↓ , PRESS←→
SYSTEM SETUP
CAMERA SETUP
TIME/DATE SETUP
RECORD SETUP
HDD MANAGEMENT
MISCELLANEOUS SET U P
TCP/IP SETUP
FACTORY DEFAULT
6. RECORD SETUP
Setting for recording
a. Press [MENU] button and enter password and press
[ENTER] button to enter into main SETUP menu.
In the main SETUP menu, select RECORD SETUP.
Default password set by manufacturer is null, therefore
just press [ENTER] button after you press [MENU] button
to enter into main SETUP menu, in case you did not
change password.
b. Select RECORD TYPE.
-TIMER : Recording at a certain time interval (DEFAULT)
-MOTION : Recording when a motion detected
-ALARM : Recording when an alarm is activated
c. Decide to overwrite or not when HDD is full.
-OFF : Stop recording when HDD is full.
-ON : Overwrite when HDD is full (DEFAULT).
d. Total recording rate (Fields/sec)
-1/1X : Records at maximum rate/60(50) Fields/sec in total
( FACTORY DEFAULT)
-1/2X: Records at half of maximum rate/
30(25) Fields/sec in total
- Possible to set from 1/1X to 1/999X.
- If you set at 1/480X, it corresponds to 960 hours recording mode in Time Lapse VCR.
e. REFRESH RATE : In Motion or Alarm recording mode, DVR system records pictures at a certain time
interval (REFRESH RATE) even though there is no motion detected or alarm activated.
-20 SEC : Records pictures from all channels at time interval of 20 sec, regardless of motion detected
or alarm activated.
f. DURATION : Records for DURATION time when a motion is detected or an alarm is activated.
- 20 SEC : Records pictures from a channel where motion is detected or alarm is activated, for 20 sec.
- 1 SEC : FACT ORY DEFAULT
g. EVENT OFF TIMER : To limit numbers of motion detected, alarm activated or video loss to be enlisted to event
list, we set EVENT OFF TIMER.
- 60 SEC : Just in case time interval between previously detected motion (alarm or loss) and currently detected
motion (alarm or loss) is longer than 60 sec, currently detected motion (alarm) is enlisted in event list.
60 SEC is FACTORY DEFAULT.
- EVENT OFF TIMER is to protect event list from being filled with motion, alarm, or video loss detected very
frequently. If time interval between previous motion (alarm or loss) and current motion (alarm or loss)
is shorter than set EVENT OFF TIMER, motion, event, or video loss is not enlisted in event list, but
recording is done as set (if it is set at Motion recording or Alarm recording).
Display of RECORD SETUP
RECORD SETUP
RECORD TYPE
OVERWRITE
TIME INTERVAL
EVENT OFF TIMER
REFRESH RATE
DURATION
: TIMER
: OFF
: 1/1X
: 60 SEC
: _ _ _ _ _ _
: _ _ _ _ _ _
SELECT , PRESS
3. Operation
Display of SET TIME/DATE
15-DVR16SAE-LAN15-DVR16SAE-LAN
ALL ABOUT IMAGE RECOGNITION & PROCESSING ALL ABOUT IMAGE RECOGNITIO N & PROCESSING
2-5. Sensor connection
Connect sensors to D-SUB 25 Pin as specified below.
2-6. Network connection
RS-232C : Connected to RS-232C port of PC to operate DVR unit with key-board of PC.
8
Notice :TERATRAY CONNECTION port must be used for connecting HDD Bay (TeraTray), and can not be
used for connecting other device. Connection must be done while power supply to DVR unit is cut.
RS 485 : Connected to P/T Controller or Speed Dome Camera
You can connect dry-contact type sensors. In case of sensors with TTL output (5 Volts system), GND of
sensor must be connected to GND of DVR unit and signal line to alarm input from D1 to D16 as shown in
following figure.
Short-circuit between any of D1 from D16 and GND is recognized as an alarm.
Relay output is output in case there is an alarm input, and is connected to external
device using COM-NO (Normal Open) or COM-NC (Normal Close) contact.
SENSOR
1
2
3
4
5
D1
D3
D2
D4
7
8
6
D5
D6
9
10
13
14
11
D7
D9
D8
D10
15
16
12
D11
D12
19
20
17
D13
D14
21
22
18
D15
D16
RJ-45 : Connected to LAN, WAN or Internet
2. Installation
GND
All GNDs are connected to each other on circuit.
4. MOTION SETUP
19
SYSTEM SETUP
CAMERA SETUP
TIME/DATE SETUP
RECORD SETUP
HDD MANAGEMENT
MISCELLANEOUS SETU P
TCP/IP SETUP
FACTORY DEFAULT
EDIT CAMERA TITLE
ADJUST COLOR
MOTION SETUP
SELECT : MENU EDIT : ENTER/↑↓←→
CELL
ON
CAM 01
X08Y07
Motion detection menu
Channel in setting
and coordinates
of current cell
Current sell
Basic display : Press [MENU] button repeatedly until you find menu item to set, and select by
pressing [ENTER] button.
In basic display of MOTION SETUP, green colored cell represent motion detection area.
CELL
ON(OFF)
Using direction keys, select cell to set and press [ENTER] button. Color of cell set is changed to green.
Sets motion detection area and sensitivity of motion to be detected.
BLOCK ON
BEGIN
END
Sets motion detection area cell by cell.
Sets motion detection area by block(X x Y).
Using direction keys, select the first location of cell and press [ENTER] button, and then select the second location of
cell using direction keys and again press [ENTER] button.
You will see color of all cells inside 2 coordinates is changed to green, motion detection area.
ALL
OFF(ON)
All cells are set as a detection area or no detection area.
When it is in ALL-OFF, press [ENTER] make all cells no detection area. When it is in ALL-ON, press
[ENTER] to make all cells detection area.
SENSITIVITY
LEVEL 10
Sets sensitivity of motion detection.
Using [Up] and [Down] buttons, choose sensitivity level.
LEVEL 01 (Dull) LEVEL 10 (Sensitive)
DETECT WINDOW
NUMBER 01
Sets numbers of cells corresponding to size of motion.
Just in case numbers of cell detected (green colored) is more than set numbers, motion is detected.
If you set DETECT WINDOW NUMBER at bigger number, motion by small object is not detected.
Press [Up] and [Down] buttons to increase or decrease cell number.
3. Operation
Display of MOTION SETUP
Exit
To exit, press [ENTER] button.
When motion is detected, it is changed
to green color and glittering.
When TeraTray is connected to DVR unit, supply power to TeraT ray first and then to DVR unit.
TERATRAY CONNECTION
DC 12V
ETHERNET
Comm Port
ALARM/ RELAY RS-232C/485
rks
PTZ
CAMERA
PC
1
10 9 8765 43211
25 24 23 22 21 20 19 18 17 16 15 14
13 12
D1D2D3D4GNDGNDD5D6D7D8GNDGNDD9
D10D11D12GNDGNDD13D14D15D16NOCOMNC
RELAY Output
15-DVR16SAE-LAN15-DVR16SAE-LAN
ALL ABOUT IMAGE RECOGNITION & PROCESSING ALL ABOUT IMAGE RECOGNITIO N & PROCESSING
2-8. Power connection
Detail setup in SYSTEM SETUP :
Refer to SYSTEM SETUP of this manual.
Connect DC 12 V power to the POWER CONNECTION on the rear panel of DVR unit.
Turn on the POWER and Log on the system
Follow direction of Log-in part of this manual to input own password and start the system.
Just press ENTER button if you do not want to input own password.
9
Connect main board and HDD using IDE HDD cable and power cable included in the package.
In case you install 2 HDDs, HDD1 must be Master and HDD2 is Slave, and jumper setting must be done
properly as specified by HDD manufacturer.
If you install just a unit of HDD, jumper setting of HDD must be on Master, as specified by HDD
manufacturer, and you can install it at any location of HDD1 or HDD2.
2-7. HDD Connection
MAIN BOARD
HDD 1
HDD 2
1
2
Fix HDD on the bottom of DVR case using screws included in the package. Screws must be inserted from
outside of the bottom.
DC 12V
2. Installation
2. CAMERA SETUP
EDIT CAMERA TITLE
CAM
CAM
CAM
CAM
CAM
CAM
CAM
CAM
CAM
CAM
CAM
CAM
CAM
CAM
CAM
CAM
Sets camera titles for display in full screen, 4-split screen, and 9-split screen.
18
Display of CAMERA SETUP
SYSTEM SETUP
CAMERA SETUP
TIME/DATE SETUP
RECORD SETUP
HDD MANAGEMENT
MISCELLANEOUS SET U P
TCP/IP SETUP
FACTORY DEFAULT
EDIT CAMERA TITLE
ADJUST COLOR
MOTION SETUP
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
[ C H -0 1 ]
[ C H -0 2 ]
[ C H -0 3 ]
[ C H -0 4 ]
[ C H -0 5 ]
[ C H -0 6 ]
[ C H -0 7 ]
[ C H -0 8 ]
[ C H -0 9 ]
[ C H -1 0 ]
[ C H -1 1 ]
[ C H -1 2 ]
[ C H -1 3 ]
[ C H -1 4 ]
[ C H -1 5 ]
[ C H -1 6 ]
,
.
<
>
(
)
=
A
B
C
D
E
F
G
CAM ↑↓ , CHAR ←→, POS ENTER
a.Press [ENTER] button to move to menu item you want to set.
b.Enter letters (Alphabet, numbers, and symbols) using [Left] and [Right] buttons.
c.Move to next camera for settings using [Up] and [Down] buttons.
d.If you have same word repeated in camera title for each channel, move to the word you want to
copy and press [Record] button for copy and move to the location to put it and press [Playback]
to paste.
CAMERA COLOR SETUP
CH NUMBER
BRIGHTNESS
CONTRAST
SATURATION
HUE
GAIN
Display of COLOR SETUP
1
-1
+3
+0
-1
-14
3. ADJUST COLOR
SYSTEM SETUP
CAMERA SETUP
TIME/DATE SETUP
RECORD SETUP
HDD MANAGEMENT
MISCELLANEOUS SETUP
TCP/IP SETUP
FACTORY DEFAULT
EDIT CAMERA TITLE
ADJUST COLOR
MOTION SETUP
SELECT ↑↓ , PRESS ←→
Adjust colors of images from cameras.
CH NUMBER
BRIGHTNESS
CONTRAST
SATURATION
HUE
GAIN
(-31~ +32)
(-31~ +32)
(-20~ +32)
(-31~ +32)
(-31~ +32)
: Select camera # from 1 to 16
: Sets brightness
: Adjust color contrast
: Adjust color saturation
: Adjust color hue
: Adjust image signal level
3. Operation
Selection of video system (NTSC/PAL system)
You can set video system in the process of booting. According to video system of camera, set video
system as follows.
NTSC system : While you press [MENU] button and [LEFT] button at the same time, turn DC power
switch on. Press two buttons until you hear beep sound from DVR unit.
PAL system : While you press [MENU] button and [RIGHT] button at the same time, turn DC power
switch on. Press two buttons until you hear beep sound from DVR unit.
From next booting, it is not necessary to set as above. DVR system memorize video setting.
In the process of booting, DVR system displays “VIDEO SYSTEM SETTING TO NTSC (or PAL)” on
bottom of screen to inform you video system you selected.
Specification of HDD : EIDE, 7200 rpm, LBA mode type (Up to 120GB)
Notice : Formatting before installation is not required, because DVR system automatically detects HDD and formats.
In the first operation after installation of HDD, first (clear all data on HDD and) set at FACTORY DEFAULT in
SETUP menu of DVR system.
Notice : To connect HDD Bay to DVR unit, first turn off power to both DVR unit and HDD Bay.
Then turn on power to HDD Bay first and then DVR unit after more than about 5 seconds.
MODE
FRZ
SEQ
ZOOM
PIP P/T
POWER
OVERWRITE
RECORD
PLAY
SETUP
12345 6
91011 12 13 14715
MENU
ENTER
8
16
CAMERA
15-DVR16SAE-LAN15-DVR16SAE-LAN
ALL ABOUT IMAGE RECOGNITION & PROCESSING ALL ABOUT IMAGE RECOGNITIO N & PROCESSING
3-1. Basic display
1. First operation
After power supply, DVR system automatically starts to record on Timer recording mode.
It is factory default setting, and user can change to other recording settings.
a. If press [Playback] button( ) shortly, playback starts from last stop point. If press [Playback] button once
more in playback mode, direction of playback is reversed.
If press [Playback] button in long time while DVR system is in stop mode, you can enter into GO TO
menu. For details, refer to playback part of this manual.
b. If press ( ) button in playback mode, [1x] is displayed, and you can select speed of playback
higher than x1.
If press ( ) button repeatedly, speed of playback is increased from 1, 2, 4, 8, 16, 32, up to 64.
To the contrary, if press ( ) button in playback in x1 speed, playback speed is decreased to ½ and
then ¼.
c. To go back to Menu, press [Menu] button while in stop mode.
2. Set time when you first operate DVR unit.
Refer to TIME/DATE SETUP in SYSTEM SETUP in this manual.
4 Display of camera channel (camera title)
In 16-split screen, camera title is shown in numbers by the system from 1 to 16, and in 4-split and
9-split screen, camera title set by user is shown.
3. To enter into 4-split, 9-split, or 16-split screen during live monitoring or playback, press [MSD] button first and
then 1, 2, or 3 respectively.
5. Shows how much space in HDD is recorded
a. R (RECORD) indicates percentage of HDD space used until now.
b. P (PLAY) indicates starting point from which next playback will start. It is the point where last
playback stopped. To start playback from the first of recording, press ( ) button to set P (PLAY) at 0.00%,
and then press [Playback] button ( ).
To replay reverse direction from the end of recording, press ( ) button to move to the end of recording,
and then press [Playback] button ( ).
2002 / APR / 01 PM 01: 00: 00
1
Basic display
R 10.56%
P 9.34%
23 4
5
6
78
9101112
13 14 15 16
5. Percentage of HDD space and next playback point
- R : Percentage HDD space used
- P : End of last playback
(Next playback starts from this point)
Status of HDD detected
???.?? : Unknown HDD detected
- - - . - -: No HDD detected
- TIM : TIMER RECOR DING
- MOT : MOTION RECORDING
- ALM : ALARM RECORDING
4. Indicates channel of camera
2. Current year/month/day/time
In playback mode, it represents time
of recording
3. Split screen
Full screen by ch, 4-split, 9-split or
16-split screen are available
Turn on the power switch, and DVR system shows live display from ch 1 to
16 as following figure.
DVR system already started to record picture data automatically.
Chapter 3 . Operation
10
3. Operation
TIM
1. indicate current status of DVR
Recording
Recording stand-by (No motion or alarm detected
in motion or alarm recording mode)
Stop
Playback in forward direction
Playback in backward direction
x times high speed playback in forward direction
x times low speed playback in forward direction
x times high speed playback in backward direction
x times low speed playback in backward direction
Pause ( Temporary stop of pal yback)
Cross color reduction setting : In 16-split live display, user
can set logic level of D/A converter in 3 steps for better
quality of OSD.
Press [UP] or [DOWN] button to adjust brightness and
color blurred on the edge of letters and at the corner of
object.
1. Basic operation
a. Press [MENU] button.
c. Select SETUP item using [Up] and [Down] buttons.
d. Press [ENTER] button to move to Sub-menu.
e. In Sub-menu, press [Up] and [Down] buttons to move and press [Left] and [Right]
button to set values.
f. Press [ENTER] button to select and [MENU] button to exit.
17
b. Enter PASSWORD and log on the system.
Settings remain unchanged after setting at FACTORY DEFAULT
1. TIME/DATE SETUP 2. All data on HDD
3. Password 4. ALARM LIST SETUP
Notice : We recommend users to clear all data on HDD and set at FACTORY DEFAULT in the very first operation
of this DVR unit.
In case you added HDD, replaced HDD or replaced EPROM (Program for DVR unit), also clear data on
HDD and set at FACTORY DEFAULT again.
Display of SETUP
SYSTEM SETUP
CAMERA SETUP
TIME/DATE SETUP
RECORD SETUP
HDD MANAGEMENT
MISCELLANEOUS SETUP
TCP/IP SETUP
FACTORY DEFAULT
SELECT UP/DOWN ,ENTER
Setting date and time in lo cal time
Setting recording type
Clearing data on HDD or HDD information
Setting password, PTZ control, buzzer, and alarm
Setting IP address & others
g. All settings done in SYSTEM SETUP is memorized automatically when you exit SETUP menu.
3. Operation
3-5. SETUP
Setting camera title, colors, motion, and others
Notice : If you press [MODE] button for a long time, you can select type of monitor. [MODE] button changes
monitor type (default mode is Composite) from (to) Composite to (from) VGA, whenever pressed, in case
VGA option is included.
If you press [MODE] button two times continuously, you can adjust screen position by pressing [LEFT],
[RIGHT], [UP], and [DOWN] buttons on the front panel of DVR unit.
Initialize system and set at FACTORY DE FA UL T
15-DVR16SAE-LAN15-DVR16SAE-LAN
ALL ABOUT IMAGE RECOGNITION & PROCESSING ALL ABOUT IMAGE RECOGNITIO N & PROCESSING
3-2. DVR SYSTEM Log-in
11
3) If you want to input for your own password,
press any buttons on the front panel,
from 1 button to 8 buttons.
If you do not want to have own password,
just press [ENTER] button.
1) After system starts to operate,
press [MENU] button to enter into
SYSTEM menu.
2) LOGIN DVR SYSTEM is displayed as
shown on the left.
Factory default password is [ENTER].
Notice : We recommend users to set own password in the first operation. For details, refer to
PASSWORD SETUP IN SYSTEM SETUP-MISCELLANEOUS SETUP.
If password you entered is consistent with password already set, “PASSWORD OK” is displayed, and you
enter into SYSTEM SETUP. If it is not, system goes back to live display mode.
LOGIN DVR SYSTEM
ENTER PASSWORD : _ _ _ _ _ _ _ _ _
INPUT YOUR OWN PASSWO RD,
THEN PRESS [ENTER]
TO EXIT, PRESS [MENU]
Enter password
Default P/W : [ENTER]
Display of Login
4) Then press [ENTER] button.
3. Operation
`
16
a. Press [Fast forward]( ) in playback mode.
b. As shown on the left, 1x is displayed, and you can
select high and low playback speed.
c. Press [Fast forward] button repeatedly to increase playback
speed, 1,2,4,8,16,32,64. Press [Fast backward] button to
decrease playback speed to ½ or ¼.
d. You can select high speed and low speed when 1x is
displayed, by pressing [Fast forward] button or
[Fast backward] button.
4. Speed of playback
2002 / APR / 01 PM 01: 00: 00
1
Display of Playback
R 10.56%
P 5.37%
23 4
5
6
78
9101112
13 14 15 16
1
1X
64X - 32X -16X -8X -2X -1X -1/2X -1/4X -1/4X -1/2X -1X -2X-4X-8X -16X -32X -64X
5. ZOOM
Press [ZOOM] button in full screen mode, and picture of that channel is enlarged two times.
Using direction keys, [Up], [Down], [Left], and [Right], you can select area to be enlarged.
This function is available for both in live mode and playback mode.
6. PAUSE
Pauses pictures during playback.
After pressing [Pause] button, press [Fast forward] or [Fast backward] buttons to move forward or backward in the
unit of field.
If you see pictures in 16-split screen, you can move picture by picture in every channel whenever you press [Fast
forward] or [Fast backward] button.
7. Others
a. DVR system memorizes status of last playback.
For instance, you searched recorded data in backward playback and stopped at the point of 45% of
total HDD space. In the next playback, DVR system automatically starts from the point of 45% in reverse
direction. It is for efficiency in search recorded data.
b. If you want to search recorded data from the first of data, press [Fast Backward] button in stop mode.
Then, “P 0.00%” is displayed on the top left, and you can search from the first if press [Playback] button.
If you want to search from the end of recorded data, press [Fast forward] button when in stop mode, then
next playback location is changed to the end of recorded data. If you press [Playback] button, playback
starts from the end in backward direction.
c. During playback, DVR system does not record.
d. If image data on the date and time you entered in GOTO menu is not exist, playback starts from the picture which
is the nearest to the date and time you set. If the date and time you entered is not between start of recording and
end of recording, playback starts from the nearest point, from the start of recording or end of recording.
3. Operation
High speed/Backward
High speed/Forward
Notice : To protect hard drive from damaged, turn off DC power switch of DVR unit after you first
press [MENU] button. If you press [MENU] button, DVR unit stops recording, and HDD
head is not in the process of writing.
Notice : Be careful to memorize own password to operate DVR unit properly.
If you forget password, contact this DVR dealer to know how to enter into SYSTEM SETUP.
15-DVR16SAE-LAN15-DVR16SAE-LAN
ALL ABOUT IMAGE RECOGNITION & PROCESSING ALL ABOUT IMAGE RECOGNITIO N & PROCESSING
12
1. Basic recording method
Press [Record] button ( ), then recording icon ( ) is displayed on the top of screen.
If DVR system is booted again, it is not necessary to set recording settings, because recording
setting remains unchanged and memorized.
Refer to SYSTEM SETUP-RECORD SETUP in this manual. (PAGE. 20)
2. FRZ (FREEZE)
If press [FRZ] button, “FRZ” is displayed on top left.
Then press number of channel you want to freeze. Picture of channel you selected is freezed,
and ( ) icon is displayed on the left of camera title.
Press [FRZ] button again to exit.
3. SEQ (SEQUENCE)
If press [SEQ] button in live display when it is in full screen of any channel, it shows full screen pictures
in rotation.
Rotation time interval can be set in SYSTEM SETUP-MISCELLANEOUS SETUP-TIMER SETUP.
4. ZOOM
If press [ZOOM] button in full screen of one of 16 channel, system enlarges this picture two times.
Using direction keys on the left of front panel, you can select area to be enlarged.
R 10.56%
P 9.34%
Current area of picture enlarged
Pictures of 16 channel are displayed in
rotation
Enlarged area moves whenever pressing
direction button, and continuous pressing
make it move faster.
Display of ZOOM
R 10.56%
P 9.34%
LR
CH-01
T
B
3-3. Recording
3. Operation
F
Channel rotation in full screen
15
1. Basic operation
a.In the picture on the right, represents 10.56% of total HDD space is spent for data recording, and next
playback will start from the point of 5.37% of total HDD space.
b. Press [Playback] button( ).
c. Playback will start at the point of 5.35% of total HDD space.
d. When [Stop] button( ) is pressed at the point of 9.34%,
DVR system memorize it(Memorize stop point of last playback).
e. If press [Playback] button( ) again, playback starts from
9.34 %(stop point of last playback).
f. When playback proceeds up to 10.56% of total HDD space,
playback is stopped.
g. If press [Playback] button( ), playback starts again from the
end of data in reverse direction.
h. If press [Stop] button( ), system goes to live display mode.
Unless you press [RECORD] button, DVR system does not
record.
2. Example of operation
a. If press [Playback] button( ) shortly, DVR system starts to replay.
b. If press [Playback] button( ) once again, direction of playback is reversed.
c. If press [Playback] button( ) in long time when DVR system is in stop mode, you can enter GOTO MENU.
d. Then you can select search by percentage, by time, and by event in GOTO MENU.
2002 / APR / 01 PM 01: 00: 00
1
R 10.56%
P 5.37%
23 4
5
6
78
9101112
13 14 15 16
1
3. Search
When DVR system is in stop mode, press [Playback] button( )
for a couple of seconds, and you can enter into GOTO MENU.
2002 / APR / 01 PM 01: 00: 00
1
Basic display of GOTO menu
R 10.56%
P 5.37%
23 4
5
6
78
9101112
13 14 15 16
[GOTO MENU]
> PERCENT
TIME/DATE
EVENT LIST
[PERCENT GOTO]
Start
End
2002 / 04 / 01 10 : 20 : 11
2002 / 04 / 01 13 : 00 : 00
RECORD …………1 0 . 5 6%
PLAY………………._ _ _ _ %
[TIME/DATE GOTO]
Start
End
Target
2002 / 04 / 01 10 : 20 : 11
2002 / 04 / 01 13 : 00 : 00
2002 / 04 / 01 11 : 50 : 00
[EVENT-LIST GOTO]
0 2002 / 04 / 01 10 : 20 : 11 M03
1 2002 / 04 / 01 13 : 00 : 00 M07
2 2002 / 04 / 01 11 : 50 : 00 M11
Select , Play or Stop
>
Using buttons from 1 to 10, set
percentage from which you want
to search, then press [ENTER]
button. Time corresponding to
the percentage you set is
displayed, and you can search
by pressing [PLAYBACK] button.
Using [Left] and [Right] buttons,
move to locations you want, and
set values using [Up] and
[Down] buttons.
Then press [Playback] button,
and playback starts from the
time you set.
Event list includes information
about motion, alarm, and
camera loss. Using direction
buttons, select event you want to
search, and press [Playback]
button to search.
M : motion , A : alarm, L: loss
M11 : Motion detected at ch #11
1
3-4. Playback
____ / __ / __ __ : __ : __
Target
3. Operation
Basic display of playback
15-DVR16SAE-LAN15-DVR16SAE-LAN
ALL ABOUT IMAGE RECOGNITION & PROCESSING ALL ABOUT IMAGE RECOGNITIO N & PROCESSING
6. P/T (PAN/TILT)
You can connect PTZ camera or speed dome camera to DVR unit, and you must input protocol of camera to control
camera while you see live pictures, using buttons on the front of DVR unit or remote controller.
a. Basic control button : ENTER - Transmit COMMAND while pressed
UP/DOWN - Selection of menu item
LEFT/RIGHT - Select Command
For details, refer to SYSTEM SETUP-MISCELLANEOUS-PAN/TILT CMD SETUP.
b. Operation : 1. Press [P/T] button.
2. Select device (PTZ camera) using [UP] and [DOWN] buttons.
3. Select Command using [LEFT] and [RIGHT] buttons.
4. After completing input protocols of PTZ camera, press [P/T] button to exit.
5. PIP (PICTURE IN PICTURE)
While you see picture of specific channel in full screen, you can see small size pictures of remaining channels in
rotation, if you press [PIP] button. Time interval of PIP (small size picture) can be set in SYSTEM SETUPMISCELLANEOUS-TIMER SETUP.
If press [SEQ] button while it is in PIP mode, picture in full screen and PIP (small size picture) are all rotate.
Full screen of selected channel
PIP (small size pictures) rotates
in time interval already set
CH-1
CH2~CH16
Display of PIP
13
3. Operation
Notice : Maximum numbers of PTZ camera can be connected to DVR unit is 4.
14
a. TIMER recording : Recording by time ( at set recording rate, fields/sec)
8. Cautions
1) When you are in SYSTEM SETUP, recording is stopped.
2) While DVR system is in playback mode, recording is stopped.
3) No recording is done in channel to which you did not connect camera.
Example : Record all images at set recording rate(fields/sec) and overwrite when HDD is full.
7. Record setting
1. Log-in to SYSTEM SETUP.
2. Mover to RECORD SETUP and enter.
3. Using direction keys, set as figure-a.
b. MOTION recording : Recording when motion is detected (MOTION DETECTION)
Example : Just record for 30 seconds whenever motion is detected, and stop recording when HDD is full.
RECORD SETUP
RECORD TYPE
OVERWRITE
TIME INTERVAL
REFRESH RATE
DURATION
EVENT OFF TIMER
: TIMER
: ON
: 1/1X
: _ _ _ _ _ _
: _ _ _ _ _ _
: _ _ _ _ _ _
SELECT , PRESS
a. TIMER recording
RECORD SETUP
RECORD TYPE
OVERWRITE
TIME INTERVAL
REFRESH RATE
DURATION
EVENT OFF TIMER
: MOTION
: OFF
: 1/1X
: 20 SEC
: 30 SEC
: 60 SEC
SELECT , PRESS
b: MOTION reco rding
1. Log-in to SYSTEM SETUP.
2. Move to RECORD SETUP and enter.
3. Using direction keys, set as figure-b.
c. ALARM recording : Recording when alarm is activated
Very similar to MOTION recording
For details, refer to RECORD SETUP (PAGE. 20) in this manual.
3. Operation
R 10.56%
P 9.34%
TIME INTERVAL : Images from cameras are coming every 1/60 sec in NTSC system and 1/50 sec in PAL system,
1/1X : Records at all images from all cameras at a time interval of 1/60 or 1/50 second
according video system.
1/2X : Records images from all cameras at a time interval of 2/60 or 2/50 second
according to video system.
TIME INTERVAL represent recording rate, however it practically indicates if it
records images at time interval of switching time, at time interval of double of
switching time, at time interval of triple of switching time, and so on.
respectively, and it is switching time.
15-DVR16SAE-LAN15-DVR16SAE-LAN
ALL ABOUT IMAGE RECOGNITION & PROCESSING ALL ABOUT IMAGE RECOGNITIO N & PROCESSING
Loading...