COP Security 15-CD55TWAI, 15-CD55TWA, 15-CD52WI Installation And Operation Manual
Installation and Operation Manual
for
High Speed Dome Camera
VER: V1.0
15-CD55TWAI 15-CD55TWA 15-CD52WI
Please read the operation manual carefully
before installing and using this unit
High Speed Dome Camera Introduction Manual
1
CAUTl0N
RISK OF ELECTRIC
SHOCK DO NOT OPEN
CAUTION：To reduce the risk of electrical shock, do not open covers.
No user serviceable parts inside.
Refer servicing to qualified service personal.
This lightning flash with arrowhead symbol is intended to alert the user to the
presence of un-insulated "dangerous voltage" within the product's enclosure that
may be of sufficient magnitude to constitute a risk of electric shock to persons.
This exclamation point symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING：To prevent the risk of fire or electric shock hazard do not expose
this camera to rain or moisture.
High Speed Dome Camera Introduction Manual
2
▌▌Important Safeguard
1. Read Instructions
Read all of the safety and operating instructions before using the product.
2. Retain Instructions
Save these instructions for future reference.
3. Attachments／Accessories
Do not use attachments or accessories unless recommended by the appliance manufacturer as they
may cause hazards, damage product and void warranty.
4. Water and Moisture
Do not use this product near water or moisture.
5. Installation
Do not place or mount this product in or on an unstable or improperly supported location. Improperly
installed product may fall, causing serious injury to a child or adult, and damage to the product. Use
only with a mounting device recommended by the manufacturer, or sold with the product. To insure
proper mounting, follow the manufacturer’s instructions and use only mounting accessories
recommended by manufacturer.
6. Power source
This product should be operated only from the type of power source indicated on the marking label.
▌▌Precautions
Operating
z Before using, make sure power supply and others are properly connected.
z While operating, if any abnormal condition or malfunction is observed, stop using the camera
immediately and then contact your local dealer.
Handling
z Do not disassemble or tamper with parts inside the camera.
z Do not drop or subject the camera to shock and vibration as this can damage camera.
z Care must be taken when you clean the clear dome cover. Especially, scratch and dust will ruin your
quality of camera.
Installation and Storage
z Do not install the camera in areas of extreme temperature, which exceed the allowable range.
z Avoid installing in humid or dusty places.
z Avoid installing in places where radiation is present.
z Avoid installing in places where there are strong magnetic fields and electric signals.
z Avoid installing in places where the camera would be subject to strong vibrations.
z Never expose the camera to rain and water.
High Speed Dome Camera Introduction Manual
3
1. Introduction
Features
Product and Accessories
4
8
2. Installation Guide
Preparations
Installation Method
Installation Dimensions
9
10
10
3. Dome Setting
DIP Switch Setup
Cabling
Check points before operation
Reserved Preset
OSD Menu Functions
14
16
18
19
21
4. How to use OSD Menu
Language
System Information
Display Setup
IDLE
Camera
Motion
Restart
Factory Default
23
23
24
26
37
42
50
51
5. Specifications
Specifications
Optional Bracket
52
54
High Speed Dome Camera Introduction Manual
4
██▐▐ FFeeaattuurreess ▌▌██
▌▌Camera Specifications
z CCD Sensor: 1 / 4 " Interline Transfer CCD
z Camera Support: CZ36SCM(COP)
Zoom Magnification: x 36 Optical Zoom, x 32 Digital Zoom
z Camera Support: FCB-EX1020(SONY)
Zoom Magnification: x 36 Optical Zoom, x 12 Digital Zoom
z Camera Support: SCM-2270(SAMSUNG)
Zoom Magnification: x 27 Optical Zoom, x 16 Digital Zoom
z Camera Support: SCM-2370(SAMSUNG)
Zoom Magnification: x 37 Optical Zoom, x 16 Digital Zoom
z Day & Night Function
z Various Focus Mode: Auto-Focus / Manual Focus / Semi-Auto Focus.
z Independent and Simultaneous Camera Characteristic Setup in Preset operation
▌▌Main Features
z Step less speed changes, auto zoom/speed matching
z Pan 0.01~360
o
/S, Tilt 0.01o~120o/S (15-CD55TWAI)
z Pan 0.01~600
o
/S, Tilt 0.01o~120o/S (15-CD55TWA)
z Pan 0.01~120
o
/S, Tilt 0.01o~120o/S (15-CD52WI)
z Auto object track with zoom in/out and motion detection (15-CD55TWAI)
z Timing actions for 7 days of programmable schedule
z Built-in Semi-conductor heater & digital temperature sensor
z PWM cooling fan vari-speed temperature control
z Reserved network interface and space for network module
z Pan Tilt accuracy +/- 0.01
o
, 256 preset positions
z 8 cruising tracks, each cruising track has 32 presets
z 4 pattern tours,10 Mins memory, 500 programmable instructions
z Multi-Protocol through RS485 or coaxial cable.
z 8 auto scan with use-defined left and right boundaries and settable scan speed
z 8 Privacy Zones with defined English camera title
z Auto Compatible PELCO_P, PELCO_D compatible
z Guard Location: the dome will rotate back to preset position after a period of
vacant time
z Alarm triggering: the alarm can trigger preset, auto scan, cruising and pattern tours functions
z Soft Address Function: the use can set up the dome address without uninstall the dome
High Speed Dome Camera Introduction Manual
5
▌▌Integrated Super Speed PTZ Rotator..
z Delicate stepping motor, stable, sensitive and accurate
z 360° Pan and 90° Tilt range (auto-flip) without blind area
z Stepless speed change, auto zoom/speed matching
z Near / far IR Light auto matches camera zoom in/out
▌▌All-weather Outdoor Design
z High die-cast alloy aluminum construction
z High Precision Mould with high heat conductivity
z Fully enclosed isolation design for heat sink
z Nanometer Dustproof, waterproof and fog-proof lens
z IP66 Waterproof
z 3000V lightning and surge current protection
▌▌Function Instructions
z Focus / PTZ Speed Auto Match
The pan/tilt rotation speed could be automatically adjusted according to the focus in/out, which
makes it much more practical for manual target tracking. (Only for the auto tracking IR speed dome)
z Power Up Action
This function enables to resume the last action executed before power down. Most of
actions such as Preset, Pattern, Swing and Group are available for this function but jog
actions are not available to resume.
z Auto Flip
When the camera tilts downward and goes just beyond the vertical position, the camera will rotate
180 degrees.
z Preset Position Set up and Call Up
In the Preset function the dome stores the current pan/tilt angle, zoom and other position parameters
in its memory. When necessary the dome recalls these parameters and adjusts the camera to a
particular position. The user can store, recall and clear the presets easily and promptly by using the
keyboard controller. The dome can store up to 220 presets.
z Auto Scan
Users can set up the left and right boundaries by control keyboard. Then speed
dome can scan between this boundary. It supports up to 8 groups of scanning paths.
High Speed Dome Camera Introduction Manual
6
z Cruising Track
The preset position can be programmed to be recalled in a set of sequences. This sequence can be
set to let the camera scan from one position to the next in a cycle at a set speed. This feature is
called the “auto cruise”. The cruise sequence and dwell time of each preset can be set. It supports
up to 8 cruising tracks, each cruising track with 32 presets.
z Pattern Tour
Dome can memorize 600s running path or 500 programmable instructions. When start pattern tour,
speed dome will move automatically according recorded action path. It supports 4 groups of pattern
tours.
z Guard Location
The dome will automatically return to preset position if there is no operation in a period of vacant
time.
z Default Action
When you start up the dome camera or do not send commands over a long time, the dome camera
will return to its default functions which include the home place, auto pan, auto cruise and pattern.
z Dome Address Setup
The dome supports up to 256 addresses and the dome will only response to the instructions given to
its own address. Please check the dip switch on the bottom of the dome for address setup.
z Manual Object Tracking
The use can move the joystick up, down, left or right to track the appearing object in the screen and
use the joystick to zoom in and out with auto focus.
z Privacy Mask Protection
Set black mask areas to protect the privacy zones. The black privacy locations can be set, and
support up to 8 mask zones.
z Timing Running Function
Users can set speed dome operation task at total 8 timing areas during 7 days.
z Coordinates and Directions Display
User can define the dome’s direction of due north, which will help to show up the exact moving
directions on screen. And zone title is supported to display when the dome moves to the specified
zone.
High Speed Dome Camera Introduction Manual
7
z Auto Tracking (only for 15-CD55TWAI)
The dome will automatically fix and track the moving object according to the user’s setup via OSD.
z Motion Detection
The dome will detect the changes in the defined video zone and trigger alarm.
It supports to 8 video Locations, each with 4 detection zones.
z PTZ and Lens Control
1 Zoom Control
Users can control zoom by keyboard to get near or far images.
dFocus Control
The default setting is auto focus. The camera will auto focus based on the center of the video
display to get the clear image. In some special occasions, the user could do the manual focus
to get the desired image effect.
eAuto Iris Control
Auto Iris is aiming to detect the environmental lights condition and adjust the iris to get the
stabilized brightness of the image.
4Auto Back Light Compensation
In the highly bright background, auto back light compensation is aiming to compensate the
brightness of the dark object and adjust the background brightness to get a clear image.
5Auto/Manual White Balance
Auto/Manual WB adjust depending on the environment light changes.
6 Day and Night Switch (Only for Day/Nigh Camera)
Speed dome camera can auto switch according to the environmental illumination changes.
7OSD Setup (Only for camera with menu)
Call upon preset No.95 to enter into OSD menu setup interface. Press “Focus” to choose
menu items and press “Iris” to set menu contents.
The information such as Camera ID, temperature, Pan/Tilt Angle, Alarm Input and Preset can
be displayed on screen.
z I/O Functions (for Advance Type)
To reject external electric noise and shock perfectly, alarm sensor Input is decoupled with photo
coupler.
Using the dry contact for alarm input and output.
If an external sensor is activated, camera can be set to move to the corresponding Preset position.
z Reserved Presets for Special Purpose
Most camera characteristics can be set up easily and directly with reserved preset, not entering
into OSD menu. For more information, refer to “Reserved Preset” in this manual.
High Speed Dome Camera Introduction Manual
8
▌▌Product & Accessories
15-CD55TWAI 15-CD55TWA 15-CD52WI
z Accessories:
User’s Manual Anti-drop Rope
Caution：DC12V/4A power for 15-CD55TWA
DC12V/5A power for 15-CD55TWAI & 15-CD52WI
High Speed Dome Camera Introduction Manual
9
██▐▐ IInnssttaallllaattiioonn GGuuiiddee ▌▌██
▌▌Preparations
z Basic Requirements
All the electric work must be finished under the latest electric & fire prevention law and rules (and
any related law and rules). Please check according to the packing list if every accessory is included.
And also make sure the installation is operated as required. Please contact us for any help during
the installation.
z Installation Space and Density Checkup
Please make sure the space is big enough to install our dome. And also ensure the density of the
ceilings or walls to hold total weight of the dome and its accessories.
z Cables Preparation
Please choose the proper cable according to the transmission distance. The min requirement of
coaxial BNC cable is listed as follows for reference:
Models
MaxDistance（Feet\Meter）
RG59/U 750ft(229m)
RG61/U 1,000ft(305m)
RG11/U 1,500ft(457m)
z Setup Dip Switch for Dome Address
※
Please turn to Dome Address Setup for details
High Speed Dome Camera Introduction Manual
10
▌▌Installation Method
The IR speed dome could be installed in wall-mount and pendant-mount
▌▌Installation Dimensions
Wall Mount
15-CD55TWAI 15-CD55TWA 15-CD52WI
Drill Drawing：
High Speed Dome Camera Introduction Manual
11
Pendant Mount
15-CD55TWAI 15-CD55TWA 15-CD52WI
Drill Drawing：
High Speed Dome Camera Introduction Manual
12
*Notice: The wall and ceiling must be thick enough to install the expansion and can bear 4 times the
weight of the dome camera itself.
z Wall-mount Installation Procedures:
1). Take out the bracket from the package (as shown), mark the installation hole positions on the
wall referencing to the bottom of bracket.
2). Drill the hole and install 4 pieces of M8 expansion bolt into the hole.
3) Take out the IR speed dome and put the cables through the bracket.
Use M5 screws to fix the bracket and dome body.
4) Use 4 pieces of M8 screw nuts with washer to fix the bracket on the wall.
High Speed Dome Camera Introduction Manual
13
z Pendant-mount Installation Procedures:
*Notice: Pendant-bracket is not designed for outdoor installation. If specially required, please do
make sure the waterproof installation of the dome.
1) Take out the bracket from the package (as shown), mark the installation hole positions on the
ceiling referencing to the bottom of bracket.
2) Drill the hole and install 4 pieces of M8 expansion bolt into the hole.
3) Take out the IR speed dome and put the cables through the sockets on the bottom of the pendant
bracket. Use M5 screws to fix the bracket and dome body.
4) Use screw nuts with washer to fix the bracket on the wall.
High Speed Dome Camera Introduction Manual
14
██▐▐ DDoommee SSeettttiinngg ▌▌██
Before the dome is installed, please finish the setup of the communication protocol, baud rate and
dome address. Set the DIP switch inside the dome body. The relative DIP switch site and connecting
wires are diagramed below for reference.
▌▌DIP Switch Setup
15-CD52WI : The dip switches are under the cover as following picture.
15-CD55TWA&15-CD55TWAI: The dip switches are under the flange as following picture.
SW1 — Dip switch for the dome address
SW2 — Dip switch for the dome protocol
High Speed Dome Camera Introduction Manual
15
z Protocol Setup (SW2)
Our IR speed dome supports two protocols including Pelco P and Pelco D.
All of them supports baud rate of 9600bps、4800bps、2400bps.
Set the No.1~4 dip switch for the protocol configuration.
Protocol SW2-1 SW2-2 SW2-3 SW2-4
PELCO-P ON OFF OFF OFF
PELCO-D OFF ON OFF OFF
Reserved … … … …
z Baud Rate Setup (SW2)
Set the No.5~6 dip switch for the baud rate configuration.
Baud Rate SW2-5 SW2-6
9600 OFF OFF
4800 ON OFF
2400 OFF ON
Reserved … …
1. If you want to control using DVR or P/T controller, their protocol must be identical to camera.
Otherwise, you can not control the camera.
2. If you changed camera protocol by changing DIP S/W, the change will be effective after you
reboot the camera.
z Dome Address Setup (SW1)
1. ID number of camera is set using binary number. The example is shown bellow.
PIN 1 2 3 4 5 6 7 8
ID Value 1 2 4 8 16 32 64 128
Ex) ID=5 ON OFF ON OFF OFF OFF OFF OFF
Ex) ID=10 OFF ON OFF ON OFF OFF OFF OFF
2. The range of ID is 1~255. Factory default of Camera ID is 1.
3. If you want to control a certain camera, you must match the camera ID with Cam ID setting of
DVR or Controller.
4. Speed dome can change the ID address and baud rate via OSD menu.
High Speed Dome Camera Introduction Manual
16
▌▌Cabling
Cabling Terminal Block
z Power Connection
Please, check the voltage and current capacity of rated power carefully.
Rated power is indicated in the back of main unit.
Rated Power Input Voltage Range Current Consumption Model
DC 12V DC 11V~13 V 5A 15-CD52WI&15-CD55TWAI
DC 12V DC 11V~13 V 4A 15-CD55TWA
z RS-485 Communication
1. For PTZ control, connect this line to keyboard and DVR. To control multiple cameras at the
same time,RS-485 communication lines of them is connected in parallel as shown below.
2. Speed Dome OSD Menu, support the distal 120R resistance of the opening and closing.
Loading...