COP Security 15-2400DT, 15-2400DK, 15-2400DR User Manual

1

2.4GHz Digital Wireless A/V/Data Transmitter and Receiver KIT
USER MANUAL

MODEL: 15-2400DK

1. Key Features

 Offer a wireless link solution audio/video/data signals connection.
 2.4 GHz frequency hopping spread spectrum module and supported max. 25 Auto

hopping channels for resisting interferences to other 2.4G devices.

 100mW RF output (Average).
 Point to point mode only.
 MPEG-4 (D1) standard video compression and stereo audio inputs.
 5-bit ID pairing key for security.
 Max. 250 meters (light-of-sight)

2. Panel View
15-2400DT

15-2400DR

①

. DC 12V IN: DC 12V power input.

②

. RS-485 I/O: 2-wire half-duplex RS-485 supported.

③

. AUDIO I/O: RCA female connectors for the stereo audio signal.

④

. VIDEO I/O: BNC female for the analog CVBS video signal.

⑤

. POWER ON or RF LINK LED:

Indications Power/RF LINK LED

Power On On

RF Link Loss Low Flashing

⑥

. RS-485 LED: Indicated to RS485 data are transmitted or received

⑦

. ID Setting: ID setting is use for paring with 15-2400DK transmitter and receiver each other.

It must be make a same ID code first before you setup the devices.

⑧

. BAUD RATE and TERMINATION: Baud rate and 120 Ohm termination setting by DIP switch.

(Note: After changing the baud rate setting by DIP switch, please re-boot the device again.)

⑨

. ANT: SMA connector for connected to 2.4 GHz antennas.

○

1

○2

○

3

○

4

○

5

○

6

○

9

○

7

○

8

2

3. Quick Installation

3.1 To set the same ID code with Transmitter and Receiver each other by 5-bit DIP switch.

3.2 To set the same Baud Rate with Transmitter and Receiver each other by 2-bit DIP switch.

3.3 Plug the Video and Audio signals to the BNC and RCA connectors.

3.4 Plug the 2.4G Antenna to SMA connector.

3.5 Please check +12VDC input, then power on the devices.

REMARK: Avoid the frequency channels have the interference; please don’t close to the 802.11 a/b/g/n AP

routers and other 2.4GHz devices.

4. Caution for Installation

4.1 Be careful; never let any water in this equipment.

4.2 If necessary, use a soft cloth moistened with alcohol to wipe off the dust.

4.3 Be extra careful not to shake the unit.

4.4 Avoid places where temperatures exceed 50°C or higher.

4.5 Avoid places where there are frequent vibrations or shocks. When any abnormalities occur, make sure to

unplug the unit and contact your local dealer.

5. Packing

5.1 Transmitter ×1

5.2 Receiver ×1

5.2 Antenna 5dBi ×2

5.3 User manual ×1

5.4 Screws ×8

5.5 Plastic-Conical-Anchor ×4

5.6 Power Adaptor ×2 [Option]

6. Specification

Items / Models 15-2400DT 15-2400DR
RF

Frequency Channels 2400 ~ 2480 MHz, 25-CH Auto Hopping

(FCC & CE RTTE)
RF TX Power 100mW (Average) -­Modulation 16-QAM,QPSK,BPSK
Min. RX Sensitivity -- -80dBm
RF Impedance 50Ω 50Ω
Distance vs. Frame Rate 250 Meters: 15 ~25 fps(NTSC) / 13 ~21 fps(PAL)

150 Meters: 20 ~30 fps(NTSC) / 17~25 fps(PAL)

100 Meters: 30 fps(NTSC) / 25 fps(PAL)

Video

Video Compression MPEG-4
Max. Frame Rate
vs. Resolution

NTSC: 30 fps at 720 × 480 (D1)

PAL: 25 fps at 720 × 576 (D1)
Bit Rate Up to 6Mbps

Audio

Sampling Rate 48KHz, Stereo
S/N Ratio 63dB

Data

RS-485 2-wire RS-485 Half Duplex

Baud Rate: 2400/4800/9600 bps

Fixed Formats:1 Start bit, 1 Stop bit, 8 Data Bits, No Parity

120 Ohm Termination Resistor ON/OFF Setting

LED Indicators

Red LED Power On and RF Link Status
Green LED RS-485 Data Link Status

Mechanical & Environmental

Power Consumption 230 mA @ 12VDC 230 mA @ 12VDC
Operation Temp.

-10°C ~ 50°C

Storage Temperature

-30°C ~ 85°C
Dimensions
(without Antenna)

118 × 75 × 25 mm

Weight (without antenna) 237 g 235 g