Cooper Security i-on 16, Scantronic i-on 16 Installation And Programming Manual
Security System
Installation and
Programming Guide
Page ii
© Cooper Security Ltd. 2009
Every effort has been made to ensure that the contents of this book are correct.
However, neither the authors nor Cooper Security Limited accept any liability for
loss or damage caused or alleged to be caused directly or indirectly by this book.
The contents of this book are subject to change without notice.
Printed and published in the U.K.
This manual applies to software used in the i-on16 control unit with version 1.00
software.
For Your Safety
This book contains several passages alerting you to potential problems or
hazards. Each of these are marked by the words Note, Caution or WARNING.:
Note: Describes conditions that may affect the proper functioning of the
equipment (but will not damage the equipment).
Caution: Describes actions that will physically damage the equipment and
prevent its proper function.
WARNING: Describes actions that are hazardous to health, or cause injury or
death.
Please pay particular attention to these marked passages.
i-on16
Page iii
Contents
1. Introduction...................................................................1
Overview .........................................................................1
End Station and Keypad..................................................... 2
Opening the End Station Case............................................................2
End Station PCB ..............................................................................3
Keypad Controls and Displays............................................................3
Opening the Keypad.........................................................................4
2. Technical Specification...................................................5
Specification.....................................................................5
General ..........................................................................................5
Security..........................................................................................5
Radio .............................................................................................6
Communications..............................................................................6
Power Supply ..................................................................................7
Electromagnetic Compatibility............................................................7
Outputs..........................................................................................7
Fuses.............................................................................................8
Electrical Safety...............................................................................8
Compliance Statements ....................................................................8
Compatible Equipment....................................................... 9
3. Installation ..................................................................10
Tools Required............................................... ................. 10
Preparation .................................................................... 10
Siting the Unit...............................................................................10
1. Fit the Control Unit Box................................................ 11
Static Precaution............................................................................11
Fitting ..........................................................................................11
2. Fit and Connect the Keypad .......................................... 12
Siting the Keypad ..........................................................................12
Fitting ..........................................................................................13
Connect Keypad to End Station........................................................13
Keypad Addressing.........................................................................14
Backlight Control ...........................................................................15
Tone Volume................................................................................. 16
3. Connect End Station to Mains ........................................ 16
Mains Cabling................................................................................ 16
Mains Connection...........................................................................17
4. Connect Wired Peripherals............................................ 17
Remote Loudspeaker (Optional)....................................................... 18
Wired External Sounders (Optional)..................................................18
Wired Outputs (Optional)................................................................18
Fit and connect the I-RC01 (Optional)...............................................18
5. Fit and Connect I-SD01 (Optional)................................. 20
Safety Notice ................................................................................20
Removing an I-SD01......................................................................22
6. Fit and Connect Battery................................................ 23
Programming a Control Unit Before Installation..................................23
7. Initial Power-Up ..................... ..................................... 23
8. Commission the System............................................... 25
4. Programming ...............................................................27
Entering the Installer Menu. ... ........................................... 27
i-on16
Page iv
Leaving the Installer Menu................................................28
Restoring the Access Codes (1
st
stage Reset) ...................... 28
Restoring All Factory Default Programming ......................... 29
Detectors/Devices ........................................................... 30
Detectors .....................................................................................30
Edit Zones .................................................................................... 31
External Siren ............................................................................... 34
Radio Keypad................................................................................ 35
Outputs ......................................................................... 36
Edit Outputs.................................................................................. 36
Setting Options................................ ... .. ... .......................38
Full Set A Name............................................................................. 38
Part Set B Name............................................................................ 39
Exit Mode ..................................................................................... 39
Exit Time...................................................................................... 39
Entry Time.................................................................................... 40
Part Set Exit Mode ......................................................................... 40
Pt. Set Final Exit............................................................................ 40
Pt .Set Entry Route As.................................................................... 40
Strobe on Set................................................................................41
Strobe on Unset ............................................................................ 41
System Options............................................................... 41
User Access .................................................................................. 41
Profiles......................................................................................... 42
Language ..................................................................................... 42
Restore Defaults............................................................................42
Installer Code................................................................................ 42
Installer Text ................................................................................ 43
Remote needs Entry....................................................................... 43
Auto Rearm .................................................................................. 43
Siren Time.................................................................................... 44
Supervision...................................................................................44
Jamming ...................................................................................... 44
Force Set...................................................................................... 44
Silence Alerts................................................................................ 45
Reporting....................................................................... 45
Alarms (ARC Reporting).................................................................. 46
Speech Dialler...............................................................................52
Line Fail Reporting......................................................................... 56
5. Testing ........................................................................ 58
View Log........................................................................ 60
6. Maintenance................................................................ 61
Appendix - Profile............................................................ 62
i-on16
Page 1
1. Introduction
Overview
The i-on16 is the control unit for a wirefree alarm system
intended for domestic and light commercial use.
The control unit comprises an end station and separate
keypad.
The end station has an ABS plastic case which contains
the radio transceiver, power supply and backup battery.
Connected to the end station by standard alarm cable is
the keypad.
The keypad allows the end user to set and unset the
system, and the installer to configure the control unit.
The keypad also contains an integral proximity tag
reader, allowing end users to control the system without
having to remember access codes.
A range of wireless peripherals is available for operation
with the control unit. These include a door
contact/universal transmitter, a passive infra red
detector, smoke detector, external siren, 4 button remote
control, and remote radio keypad.
The control unit supports 16 wirefree alarm zones, 4
hardwired transistor outputs, 16 four button remote
controls, 16 two button panic alarm, and 16 users.
When fitted with an optional plug on module the control
unit can send recorded speech messages over the public
switched telephone network (PSTN). The module can also
report alarm information using standard protocols such as
Fast Format and Contact ID.
This manual shows the simple procedure required to
install the control unit and its keypad. When you have
completed the physical installation please consult the
Programming section for details of configuring the system
to meet your exact requirements.
Introduction i-on16
Page 2
End Station and Keypad
Opening the End Station Case
WARNING: When connected to the mains with power
applied mains voltages are present on the shrouded
heads of the terminal screws of the mains connector (“7”
in figure 1).
To gain access to the interior of the end station undo the
two screws at the top of the case. Pull the top of the lid
down, and then lift the lid out of the retaining lugs at the
bottom of the case (see Figure 1.)
Figure 1 shows the interior of the end station.
1
2
3
1
3
4
5
6
7
3
9
3
8
2
2
10
1. Central fixing keyhole. 6. Transformer.
2. Aerials. 7. Mains connector block.
3. Fixing holes. 8. Cable entry hole for mains.
4. Printed circuit board (PCB). 9. Back Tamper switch (if fitted).
5. Cable entry holes for pcb. 10. Connector pins for Lid Tamper.
Figure 1. Control Unit
i-on16 Introduction
Page 3
End Station PCB
Figure 2 shows the controls and connectors available on
the end station PCB.
0V 0V 12V 12V0V 12V A B0V 12V 1 2 3 4
TR14V4 - LS +
AUX AUXBUSAUX OUTPUTS
2
3
5
9
11
8
6
7
11
4
10
1. Aerials. 7. Holes for module support pillars.
2. 20VAC Input (from transformer). 8. RF receiver.
3. Battery input (12VDC). 9. “Heartbeat” LED.
4. Kick start pins. 10. Connector pins for tamper switch.
5. Connector block. 11. Sockets for communicator (I-SD01).
6. Reset codes pins.
Figure 2. End Station Printed Circuit Board
Keypad Controls and Displays
Figure 3 shows the controls and displays available on the
keypad.
A
B
C
D
1
4 ghi
7 pqrs
*0#
2 abc
5 jkl
3 def
6 mno
8 tuv 9 wxyz
2
3
4
6
5
8
7
1
1. LCD display . 5. Setting and unsetting keys.
2. Programming keys. 6. Panic Alarm (PA) keys.
3. Navigation keys 7. Number/text keys.
4. Alert LEDs 8. Set/Unset LEDs.
Figure 3. Controls and Displays
Introduction i-on16
Page 4
Opening the Keypad
To open the keypad first gently prise off the trim on the
front and remove the two screws. Next, carefully lever
the front of the keypad (containing the pcb and display)
away from the keypad rear housing.
Figure 4. Opening the Keypad
2
4
3
3
1
1. Central keyhole. 3. Cable entry.
2. Rear tamper shroud. 4. Fixing holes.
Figure 5. Keypad Rear Housing
1
4a
4b
3
4
5
2
4
3
2
ABCD-ON
ON
BRIGHT
BACKLIGHT
ET B A 12V 0V
1. Sounder. 4. Jumpers for addressing and LED function:
2. Sounder volume control. 4a Addressing
3. Tamper switch. 4b LED functions
5. Connector for end station.
Figure 6. Keypad PCB
i-on16
Page 5
2. Technical Specification
Specification
General
Product name i-on16.
Product Description 16 radio zone endstation with
remote keypad.
Manufacturer Cooper Security Ltd.
Environmental Class II.
Operating temperature Tested -10 to +55°C.
Dimensions:
End station 384 x 245 x 94, mm HxWxD.
Keypad 115 x 156 x 34, mm HxWxD
Weight:
End station 1.1 kg (without stand-by
battery).
Keypad 0.32 kg
Case material ABS.
Zones 16 radio.
Remote controls 16.
Panic Alarms 16.
Outputs 4 wired.
Internal Clock ±10 minutes over one year
(depending on the accuracy
of the mains supply
frequency).
Log capacity 250 events minimum, stored
in flash memory (requires no
support battery)
Security
Security Grade Grade 2x.
Radio detector differs 16,777,214 (2
24
-2).
Radio Supervision Programmable.
Access code 4 digits, all four digits may be
any number 0 to 9, giving
10,000 differs.
Number of user codes 16 plus installer
Technical Spec ification i-on16
Page 6
Code blocking Blocked for 90s after four
incorrect codes in series.
Proximity tag differs 4,294,967,296 (2
32
)
Radio
Radio Section Operating frequency
868.6625MHz Narrowband.
EN 300 220-3.
EN 300 330-2
Telefication
Transmitter range The range of the transmitters
compatible with this control
unit depends on the
environment in which they
are installed. As a guideline,
most transmitters will work
up 200m range in free space
conditions.
Communications
Uses plug on modules with proprietary interface between
control unit and module.
Note: Not suitable for a policed system.
I-SD01 Communication Module/PSTN
The I-SD01 module provides connection to the PSTN. The
module allows both speech messaging and alarm
signalling. When fitted to the control unit speech
messages can be configured to be up to 30s long (one
10s home message and four consecutive alarm messages
of 5s each).
The I-SD01 module meets the performance criteria of D 2,
M2, S1, I0, T2 and A0 as described in EN50136-1-1
subject to network conditions.
ATS rating ATS 2 (EN50131-1)
This product can share a PSTN line with other telephony
or fax equipment.
REN 1
i-on16 Technical Specification
Page 7
Power Supply
This product complies with the requirements of EN501316 Type A power supply at Grade 2 and environmental
class 2.
Mains power supply 230VAC +10%/-15%, 170mA
max, 50Hz.
End station psu 13.7VDC, 1.5A max
End station consumption 145mA.
Communicator consumption 50mA max
Keypad consumption 30mA (backlight off)
45mA (backlight on)
65mA (backlight on max)
Standby Battery 12V, 7Ah sealed lead acid.
Standby time: more than 12
hours.
Max recharge time: less than
72 hours.
Battery charge limit 270mA
12V Aux supply (inc LS) 13.7VDC +0.1/-0.4 @ 850mA
max.
14V4 supply 14.4V +0.1/-0.2 @ 230mA
12V Keypad bus 13.7V =0.1/-0.5 @ 400mA
max
Monitoring includes Mains fail, battery low
voltage, battery failure.
Electromagnetic Compatibility
Immunity Conforms to EN50130-4.
Emissions Conforms to EN61000-6-3.
Outputs
O/P 1 - 4 Open collector transistor,
+12VDC when inactive, 0V
when active. 500mA max.
See page 37 for programming
details.
LS (loudspeaker) Min impedance 16 Ohm,
current consumption from
12VAux = 280mA in alarm.
Technical Spec ification i-on16
Page 8
Fuses
The control unit has a 250mA mains fuse.
Electrical Safety
Conforms to EN60950-1.
Compliance Statements
This product is suitable for use in systems designed to
comply with PD 6662: 2004 at grade 2x and
environmental class II.
This product complies with the requirements of 50131-3
at grade 2 and environmental class II.
This product complies with the requirements of EN501316:2008 at grade 2 and environmental class II.
When fitted with an I-SD01 this equipment is compliant
with EN 50136-1. It allows the alarm transmission system
to meet the performance requirements of EN 501311:2006 ATS 2 provided that:
a) It is installed in accordance with the installation
instructions.
b) The connected PSTN is functioning normally.
If the installer selects a non-compliant configuration
then they must remove or adjust compliance
labelling.
i-on16 Technical Specification
Page 9
Compatible Equipment
706rEUR-00 Two button PA/tilt switch transmitter
710rEUR-00 Two button PA
713rEUR-00 Pet tolerant PIR
714rEUR-00 PIR Transmitter (Small case)
720rEUR-00 Smoke Detector Transmitter
726rEUR-50 Long range hand held PA
726rEUR-60 Short range hand held PA
734rEUR-00/01 CC/FSL Door Contact Transmitter (white)
734rEUR-05/06 CC/FSL Door Contact Transmitter (brown)
738rEUR-00/04 Spyder shock sensor (white/brown)
739rEUR-25 Sentrol glass break detector (no tamper)
760ES External Wireless sounder
I-FB01 Four button remote con trol
I-KP01 Keypad
I-RC01 Relay Card
I-RK01 Radio Keypad
I-SD01 Communication module
9040UK-00 Speaker boxed
i-on16
Page 10
3. Installation
WARNING: Exposure to Radio Frequency Radiation
The radiated output power of this device is below those
levels considered safe by European exposure limits.
Nevertheless, when fitting the product place it in such a
manner as to minimise the potential for human contact
during normal operation. To minimise exposure, users
should be more than 200 mm from the device during
normal operation
Tools Required
790r signal strength meter and 734r test transmitter.
Flat screwdriver (small).
Philips screwdriver.
Drill.
5mm drill bit.
M5 36mm (four off) and 25mm screws (three off).
Wallplugs, filler.
Preparation
Before installation you should carry out a survey of the
site. You need to know how many and what kind of
detectors will be transmitting to the control unit. You also
need to assess where the control unit must be placed in
order to receive signals from the detectors successfully.
To do this you should conduct signal strength tests.
Cooper Security produce the Scantronic 790r hand held
signal strength meter for this purpose. Alternatively, you
can power the control unit from a battery and use its
built-in testing facility to measure the signal strength
from a detector that you temporarily place at each
planned location.
Siting the Unit
Do site the unit:
Upright (battery at the bottom).
Within a protected zone.
i-on16 Installation
Page 11
As high as possible. However, do make sure that the
unit is on a similar level to the other transmitters or
receivers.
Do NOT site the unit:
In the entry or exit zones, or outside the area covered
by the alarm system.
Close to or on large metal structures.
Closer than one metre to mains wiring, metal water o r
gas pipes, or other metal surfaces.
Lower than two metres from the floor (ideally).
Inside steel enclosures.
Next to electronic equipment, particularly computers,
photocopiers or other radio equipment, CAT 5 data
lines or industrial mains equipment.
Note that some window glasses, especially those sold as
“insulating” or “energy conserving” may be coated with
thin metal or conducting films. These glasses are
particularly poor at transmitting radio waves.
If fitting two wired keypads make sure that you do not
place the keypads within one metre to each other. (The
proximity tag readers in each keypad will interfere with
each other.) This includes placing keypads on opposite
sides of the same wall.
1. Fit the Control Unit Box
Static Precaution
Like many other electronic products, the control unit
contains components that are sensitive to static
electricity. Try not handle the PCB directly. If you must
handle the PCB, take the standard precautions against
damage by static electricity.
Fitting
Cooper Security recommend that you use at least four
fixing holes when mounting the back of the end station
on a wall. Use an No10/M5 countersunk screw at least
36mm long. Figure 7 shows the fixing holes and cable
entries.
Installation i-on16
Page 12
Protect the unit from dust and drilling debris when drilling
the fixing holes.
1. Fixing holes.
2. Cable entries.
1
1
2
1
1
2
Figure 7. Fixing Holes and Cable Entries
2. Fit and Connect the Keypad
Siting the Keypad
Do site the keypad:
Within the area protected by the alarm system.
At a convenient height and location for the user.
Out of sight of potential intruders.
Do NOT site the keypad:
Next to electronic equipment, particularly computers,
photocopiers or other radio equipment, CAT 5 data
lines or industrial mains equipment.
Where the cable run from the end station will be longer
than 100m (see page 14 ).
i-on16 Installation
Page 13
Note: Do not site two or more keypads closer than one
metre together, otherwise their prox readers will
interfere and be unable to read tags.
Fitting
Use M5 25mm countersunk screws in at least three fixing
holes when mounting the back of the keypad on the wall.
Figure 8. Screw Keypad Back Box to Wall
Connect Keypad to End Station
Cable Type
In general, the control unit requires standard 7/0.2 unscreened alarm cable for wiring to keypads.
Screened cable may prove necessary if the installation
site has equipment that produces high levels of R.F.
(Radio Frequencies), for example welding equipment. If
screened cable is required, you should keep to the
following guidelines:
1. Avoid earth loops by connecting the screen on the
cable to mains earth at the end station but not at the
keypad.
2. The continuity of the cable screen is most important
and screens MUST be continuous along the full length
of the cable.
3. If the cable enters any metal enclosure, ensure the
screen is isolated from the case.
Installation i-on16
Page 14
Cable Segregation
Segregate the keypad cabling from any other wiring, such
as mains supply cables, telephone cables, computer
network cables and R.F. cables. Use cable ties to keep
cables separated.
Keep the keypad cable clear of cables supplying sounders
or extension loudspeakers.
Connection
You can connect up to two keypads to the end station.
You may connect the keypads either serially, or in parallel
at the end station connector. The cable length from
control unit to the most distant keypad should not exceed
100m.
0V 0V 12V 12V0V 12V A B
AUX AUXBUS
ET B A 12V 0V
Figure 9. Keypad Connection
Keypad Addressing
Each keypad connected to an end station must have a
unique address. See Figure 6 on page 4 for the position
of the addressing jumpers. Do not fit links to jumpers 3
or 4.
i-on16 Installation
Page 15
MENU
AB1
4 ghi
7 pqrs
*0#
2 abc
5 jkl
3 def
6 mno
8 tuv 9 wxyz
*0#
MENU
AB1
4 ghi
7 pqrs
2 abc
5 jkl
3 def
6 mno
8 tuv 9 wxyz
4
3
2
4
3
2
4
3
2
4
3
2
Figure 10. Keypad Addressing Jumpers
Backlight Control
You can control the appearance of the keypad backlights
and set/unset LEDs by fitting links over the appropriate
jumpers on the keypad pcb (see Figure 6 on page 4 for
the position of the jumpers).
The jumpers have the following functions:
MENU
AB1
4 ghi
7 pqrs
*0#
2 abc
5 jkl
3 def
6 mno
8 tuv 9 wxyz
ABCD-ON
The set/unset leds are
disabled.
MENU
AB1
4 ghi
7 pqrs
*0#
2 abc
5 jkl
3 def
6 mno
8 tuv 9 wxyz
ABCD-ON
The set/unset leds shows
the setting status of the
system. (Full set is led A.)
MENU
AB1
4 ghi
7 pqrs
*0#
2 abc
5 jkl
3 def
6 mno
8 tuv 9 wxyz
ON
BRIGHT
BL
The key backlights are
disabled. They will glow
briefly for five seconds
when a user presses a
key.
MENU
AB1
4 ghi
7 pqrs
*0#
2 abc
5 jkl
3 def
6 mno
8 tuv 9 wxyz
MENU
AB1
4 ghi
7 pqrs
*0#
2 abc
5 jkl
3 def
6 mno
8 tuv 9 wxyz
ON
BRIGHT
BL
The key backlights glow,
all the time at normal
intensity.
MENU
AB1
4 ghi
7 pqrs
*0#
2 abc
5 jkl
3 def
6 mno
8 tuv 9 wxyz
MENU
AB1
4 ghi
7 pqrs
*0#
2 abc
5 jkl
3 def
6 mno
8 tuv 9 wxyz
ON
BRIGHT
BL
The keypad backlights
glow all the time, extra
bright.
Installation i-on16
Page 16
Tone Volume
To adjust the volume of tones from the keypad:
Louder
Note: This control changes the volume of
non-alarm tones (for example
Exit/Entry tone). The volume of alarm
tones is fixed.
Softer
Figure 11. Adjusting Tones and Chime Volume.
3. Connect End Station to Mains
WARNING: The end station should be connected to the
mains supply by a qualified person. Once connected to
the mains and power is applied then mains voltages are
present on the shrouded heads of the terminal screws of
the mains connector.
Mains Cabling
Make sure that the mains supply cable does not run
vertically behind the aerials within the end station case.
>1m >1m
Figure 12. Mains Cabling
i-on16 Installation
Page 17
If you wish run mains cable through the side of the case,
make sure that they are horizontal for the last metre
before entering the case.
Mains Connection
Figure 13 shows the mains connection. Connect to a
suitable supply using a double pole disconnect device in
accordance with EN60950-1.
L
N
T 400mA 250
V
230V ~50Hz 200mA
Figure 13. Mains Connection
Caution: Do not apply power at this point.
4. Connect Wired Peripherals
The end station pcb provides four connectors for wired
outputs. Each of these outputs is driven by a transistor,
and is capable of sinking a maximum 500mA when
active. The outputs are 0V when active, +12V when
inactive.
Figure 14 shows examples of connecting wired
peripherals.
Loading...