Page 1
24V Rechargeable Lawn Mower 9806
Instructions
Victor Garden Tools
Please read carefully before use
and retain for future reference.
Please read this guide and
use these operating
instructions to become
familiar with the mower and
its features. The charging of
batteries, operation of the
mower, and notes on safety
and maintenance
procedures are important
for the safe use of this
product.
Page 2
W
ARNING
W
hen using an electrical appliance, basic safety
precautions should be observed, including the
following, to reduce the risk of the fire, electrical
shock or injury:
1. Read the instructions carefully. Be familiar with the controls and the
p
roper use of the mower.
2. This mower is not a toy.
3. Never allow children or people unfamiliar with these instructions to
u
se the mower. Local regulations may restrict the age of the operator.
4. Never mow while people, especially children, or pets are nearby.
5. The operator or user is responsible for accidents or hazards occurring
to other people at their property.
6. Mow only in daylight or in good artificial light.
7. Avoid operating the mower in wet grass, where feasible.
8. Walk, never run when operating.
9. Do not operate the mower when barefoot or wearing open sandals.
10. Thoroughly inspect the area where the mower is to be used, and
move any object which may jam or be thrown by the machine.
11. Always be sure of your footing on slopes, do NOT mow excessively
steep slopes.
12. Mow across the face of slopes, never up and down.
13. Exercise extreme caution when changing direction on slopes.
14. Use extreme caution when reversing or pulling the unit towards you.
15. Do not put hands or feet near rotating parts. Keep clear of the
discharge opening at all times.
16. Never pick up or carry the mower while the motor is running.
17. Stop the blade if the mower has to be tilted for transportation when
crossing surfaces other than grass, and when transporting the mower
to and from the area to be mowed.
18. Never operate the mower with defective guards, or without safety
devices, for example deflectors.
19. Switch on the motor according to instruction and with feet well away
from the blade.
20. Keep the mower on a flat, even surface when switching on.
21. Keep all nuts, bolts and screws tightened to ensure the equipment is
in safe working condition.
22. Be careful when adjusting height, ensure that the battery is removed
and keep fingers away from all moving parts.
23. Do not handle charger or unit with wet hands.
24. Use only as described in this manual.
25. DO NOT attempt to use the charger with any other product nor
attempt to charge this product with another charger.
26. DO NOT abuse the charger cord; never carry the charger by the cord
or pull cord to disconnect from an outlet, grasp the plug and pull to
disconnect.
27. Keep charger cord away from hot surfaces.
28. This product includes lead acid (Pb) batteries; do not incinerate
batteries or expose to high temperatures, as they may explode.
29. Leaks from battery cells can occur under extreme conditions. If the
liquid gets on the skin wash immediately with soap and water. If the
liquid gets into the eyes, flush them immediately with clean water for
a minimum of 10 minutes and seek medical attention.
30. Keep hair, clothing, fingers and all parts of body clear of moving
parts.
31. Dress properly! Do not wear loose clothing or jewellery which can be
caught by moving parts. Use of non-slip footwear is recommended.
32. DO NOT attempt to repair any damaged parts on this product unless
you are qualified to do so.
33. DO NOT operate with wet hands.
34. DO NOT use any power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal injury.
35. Avoid accidental starting. Ensure the switch is in the off position
before plugging in. Carrying power tools with your fingers on the
switches or plugging in power tools that have the switch on invites
accidents.
36. DO NOT overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected
situations.
Page 3
Victor Garden Tools
USING THE LAWN MOWER
WARNING
For safety reasons persons of less than 16 years of age or persons not
familiar with these operating instructions must not use the lawn mower.
This mower is designed for use on residential lawns. It is not designed
for commercial use or for use in public facilities, parks, sporting grounds,
roads, or in agriculture or forestry areas.
This mower is for cutting lawns only. It must not be used to trim hedges,
bushes or shrubs, for cutting or pruning, or for any mowing where both
wheels and the roller are not fully supporting the mower.
Damage to blades or other parts of the machine caused by
stones or other debris being “mown” up will not be covered
under this warranty! Always ensure the work area is clear
before use.
PARTS LIST
Please check when
unpacking the unit to be
sure that all items listed
below are included:
1. Main unit
2. Safety switch
3. Lever switch
4. Battery pack
5. Grass catcher
6. Upper handle
7. Middle handle x2
8. Lower handle
9. Nuts and bolts x8
10.Charging adaptor
11. Height adjustment knob
12. Cable clips x3
13. On/Off switch
14. Reset button
ASSEMBLY
Unpack and remove the whole mower from
packaging, and ensure all the parts are present.
CAUTION: remove the battery before
assembling the unit.
1. Set the cutting height to the highest setting.
This will make it easier to attach the Lower
handle section (8). It is easiest to fit the handle
when the mower is flat on the ground and the
handle is in a perpendicular position.
2. Fit the Lower handle (8) onto the two large
lugs on the Main unit (1). Fit one side and then
flex the other side of the handle until it fits the
opposite lug. (See Figure 2).
3. Assemble the Upper handle (6) to the Middle
handle (7). Use two sets of the nuts and bolts
(9) to secure in place. Make sure that the Upper
handle (6) is facing up (safety button facing up)
(see Figure 3). If you have incorrectly assembled
this part, disconnect and re-assemble in the
correct orientation.
4. Use two sets of the nuts and bolts (9) to
assemble the Upper and Middle handle
assembly to the Lower Handle (8). The nuts
should be positioned on the inside of the
handle and the bolts on the outside.
(See Figure 4)
5. Once the Handle is assembled connect the plug on the handle
cable to the socket on the Main unit. Tighten the screw ring to
secure the cable. (See Figure 5)
6. Secure the cable to the handle using the three cable clips.
(See Figure 6)
7. Attach the Grass catcher to the mower base Note: This mower
can be used with or without the Grass catcher.
Step 1: Place the two Grass catcher side bars onto both sides of the Grass catcher Hooks
as shown in Figure 7.
Step 2: Wrap the Security Belt, located on the
back of the Grass catcher, around the
centre joint of the Lower handles and lock
buckle into place, as shown in Figure 8.
Note the length of the Security Belt can be
adjusted by modifying the loop length.
(See Figure 8)
Figure 8
Figure 7
Figure 6
Figure 5
Figure 4
Figure 3
This side up
F
igure 2
Lower
h
andle
Lug
Page 4
CHARGING INSTRUCTIONS:
There are 5 LED on the main unit, the first three
LEDs show the power capacity of the mower
during operation. When the first 3 LEDs turn off
and the fourth LED becomes fainter, you are
being reminded that the mower needs to be
charged. The last LED is the charging indicator.
NOTES:
• To keep the battery in prime condition it is
best to charge the battery after each use, and
every 3 months if stored without use. After
each use charge for 24 hours to ensure the
battery is fully charged.
IMPORTANT: Charge the battery after
each use. Never store the unit with a flat
battery.
• The battery will not be damaged if it is
charged for longer than 24 hours, but it is
advisable not to leave it on for more than 48
hours, since this might shorten the battery life.
• Ensure the battery is fitted and locked
correctly before mowing, or else, this product
will not work and be damaged.
• Only use the charger supplied with this
product. Do not attempt to charge this
product with any other charger nor attempt to
charge any product with this charger, as it can
cause damage and will invalidate your
guarantee.
BATTERY CHARGING AND RECHARGING
Before first use charge the battery for 24 hours.
Warning: if the battery is damaged
in any way do not attempt to charge
it, and replace it immediately.
The battery does not have to be removed
from the mower to be charged.
To charge the battery in the mower, plug
the charger into the battery socket.
Plug the charger adaptor into a suitable electrical socket.
Once the battery is fully charged remove the charger connector from the battery
a
nd unplug the charger adaptor from the mains socket. Do not pull the charger
by the cord.
Charging battery out of mower
First turn the knob on the battery lid anti-clockwise, then raise the handle and lift
battery out of the mower. Place the battery on a dry, flat and non-slip surface,
and plug the charger connector into the battery socket. Charge the battery for 24
hours each time. Red LED light indicates that battery is charging, but will NOT
turn off once battery is fully charged.
Charging battery in mower
Lower it into the cavity on the top of the unit in the correct orientation. Ensure
the handle is pressed down and then turn the knob on the lid clockwise. If the
battery does not fit correctly, remove it and check there are no obstructions.
Ensure that the machine is SWITCHED OFF when recharging battery. As a safety
feature the battery will NOT recharge if the machine is switched on. The Red LED
light on the Main unit indicates that the battery is charging, but will NOT turn off
once battery is fully charged.
Charging the battery in the mower
Charging battery out of the mower Red LED means charging
Page 5
OPERATION
Cutting Height Adjustment
CAUTION: For safety ensure that the Battery is removed from the unit
before adjusting the cutting height.
The cutting height of the unit may be adjusted from approximately 1in (2.5cm)
up to approximately 2in (5cm). The mower has three height positions. To prevent
overloading the mower when cutting long, thick grass it is recommended to
make one cut at the highest setting, then another cut at a lower setting. Adjust
t
he mower to the desired height as follows:
(1) Ensure that the roller is fitted flat, it is recommended that the height is
adjusted on a level surface. It is also recommended that the Grass catcher be
removed as this will allow easier access to the adjustment knobs.
(2) Loosen the two large knobs, one on each side of the mower body, to allow
movement of the roller arms. It is not necessary to remove the knob.
(
See Figure 9)
(3) Slide the roller supports until the roller is at the required position, ensuring
that it is level and the knobs are at the same height.
(4) Tighten the knobs on both sides ensuring they are at the same height and
properly secured. Low cut height - for short, dry grass; High cut height - for
long, thick, or wet grass.
(See Figure 10)
Blade Adjustment and Lubrication
WARNING: Blades are extremely sharp, to avoid injury be
careful not to touch blades when make adjustments.
R
emove the battery before adjusting the blades.
Blades have been pre-adjusted prior to leaving factory, mis-alignment
can sometimes occur; this can be caused by blades being too loose
or too tight against the cuttingbar. This can cause an uneven cut or
make the mower hard to push.
To correct misalignment, adjustments to the cutting bar are needed.
Each end of the cutting bar can be adjusted separately.
Turn the two adjustment nuts clockwise to tighten; this moves the
cutting bar closer in towards the blade. Turn the two adjustment nuts
anti-clockwise to loosen and move the cutting bar further away from
the blade.
NOTE: Adjusting the nuts while making blade adjustments is a very
sensitive procedure. A turn of 1/16in is considered a major
adjustment. Before tightening one adjustment nut, make sure to
adjust the opposite nut an equal amount.
Do not over-tighten adjustment nut, as this could damage cutting
bar.
To check for correct adjustment insert a piece of paper between the
cutting cylinder and the straight blade.
Check with a piece of paper at each end of the blade to ensure
correct adjustment along the length of the blade. When the cutting
cylinder is turned by hand the paper should be cut cleanly.
If the paper is not cut then gradually tighten the nuts until the paper
can be cut cleanly.
To maintain maximum run time and smooth, efficient cutting
performance, an oil or spray lubricant can be applied to the edge of
the straight blade and the shaft bearings.
Victor Garden Tools
Adjustment nut
Figure 10
Low cut
High cut Knob
Figure 9
Page 6
CLEANING & MAINTENANCE
CAUTION: Remove the battery before carrying out any
cleaning or maintenance. This will prevent you accidently
turning on the unit whilst cleaning it.
Check for any faults such as loose or damaged blades,
loose fittings, and worn or damaged components. If
necessary carry out any repairs before using the mower
again.
Check that covers and guards are correctly fitted, and are
not damaged in any way.
Clean the unit using a soft brush or cloth. Do not use
abrasive material to clean the product or immerse it in
water.
Do not pick up liquids or use on wet ground.
Do not use on concrete, tarmac or other rough surfaces.
Do not pick up pieces of string, stones or fabrics with the
mower.
Be aware of raised areas in lawns such as paving stones or
manhole covers that can damage the blades.
Clean the exterior of the machine thoroughly using a soft
brush or cloth. Do not use water, solvents or polish. Spray
the cutting cylinder and lower blade with a low viscosity
oil, such as a spray oil. Brush away any build-up of grass or
leaves on the blades.
STORAGE
Before storing, remove the battery. Turn the unit on its side
and clean the blade area. If grass cuttings are compacted
in the blade area, remove with a wooden or plastic
implement.
Remove all grass and debris, store the unit in a dry place,
out of the reach of children, and oil the blades.
Do not place other objects on top of the machine.
Always charge the battery after use, and every three
months if stored for a long period of time.
For storage in confined spaces the handles can be removed
from the mower.
Disconnect the power cord and flex the lower handles to
remove from the frame locating lugs.
Starting and Stopping
WARNING
Before starting the mower, check within the blade area for any foreign objects and remove
them.
Do not operate the mower on areas other than turf surfaces. The mower should be sitting on
its wheels on a level part of lawn before starting operation.
(1) To start the mower, first turn on the red on/off switch (13) on the Main unit to the ON
position, then press the safety button (2) with one hand and pull the starting lever (3)
back toward the handle grip with the other hand.
(2) To stop the unit, just release the lever (3), the motor will switch off, then turn off the
on/off switch (13) on the Main unit.
(3) The mower may be restarted at any time with the same procedure.
(4) The blades continue to rotate for a few seconds after the mower is switched off. Wait for
the blades to stop turning before clearing any grass or putting your hands near the
blades.
Reset Button ( to be used if and when you overload the motor)
The reset button (14) on the main body of the machine is to prevent any damage occurring
to the battery or the motor due to a current overload, such as from the blade jamming.
To restart the mower wait for a few seconds then press the reset button so that it is level
with the mower casing.
If you use the Reset button (14) then following actions are recommended:
(1) Do not force the unit to cut in thick or wet grass as this can overload the motor.
(2) Make a first cut with a high cutting height then make a second cut with a lower cutting
height. (See cutting height adjustment section on previous page).
(3) Push the unit more slowly.
(4) Check the blade is correctly adjusted so the grass is cutting cleanly.
(5) Clean the blades and remove any grass or objects that may be causing the mower to
stall.
Mowing
• To obtain a clean cut, push the unit in straight lines (passes) at a deliberate walking pace.
Overlap the passes to even the cut and to avoid any uncut strips.
• If you hear the motor in the unit change pitch dramatically while mowing, it may be
overloaded. Attempting to force the mower to cut may damage the motor.
• Check to see if the grass is very thick or long, a first cut with height set higher will help
reduce the load on the motor. (See Cutting Height Adjustment section).
• Push the unit more slowly when cutting thick, long, or wet grass.
• The area of cut depends on the lawn conditions, grass thickness, grass length, moisture
content, and height of cut.
• For the maximum area of cut it is recommended to cut the lawn more frequently, mow in
dry conditions, select a high cutting height, and walk at normal speed.
• Start mowing around the edges of the area to be mowed, then cut the central area in
strips.
Mowing using the grass catcher (supplied accessory)
The grass catcher (5) collects the clippings as it mows. It attaches at the grass catcher hooks
on the mower and by the strap to the mower handle. Mow using the same procedure as for
normal mowing.
Page 7
Victor Garden Tools
TROUBLESHOOTING
PROBLEM POSSIBLE REASON POSSIBLE SOLUTION
Mower fails to start 1. Battery flat 1. Recharge battery
2
. Battery is not fitted correctly 2. Check the battery is correctly fitted and fully pushed down
3. Protective cut-out operated 3. Press reset button down
4. Faulty switch 4. Press the safety button (2) FIRST and then pull the lever switch
(3) back, not at the same time
Does not cut grass 1. Poor blade adjustment 1. Tighten blade – see blade cutting adjustment
Stalls frequently 1. Poor blade adjustment 2. Grass caught around blades
2. Tighten blade – see blade cutting adjustment 2. Remove any grass or debris that may be jamming the blade
Low cutting time 1. Battery flat 1. Recharge battery for 24 hours
2. Blade too tight or dirty 2. Adjust blade or clean blade, oil blade and bearings
3. Guard has build up of debris 3. Clean guard
4. Grass thick, long, or wet 4. Adjust to higher cut height, wait for dry conditions
5. Cutting height too low. 5. Set to higher cut height
Reset button operates frequently 1.Motor overloaded 1. Adjust cutting height to a higher setting and take a lighter cut
2. Blade jammed 2. Push the mower more slowly
3. Check blade is correctly adjusted so grass is cut cleanly
4. Remove any grass/debris that may be causing a jam
Battery flat and will not recharge 1. Faulty charger 1. If the charger does not get warm then charger has fault. If
charger gets warm then fault with battery. Call customer service
helpline
2. Battery stored for long time without 2. Replacement battery
being charged
Excessive noise 1. Blade and bearing require lubrication 1. Apply oil or lubricating spray to blade and bearing
2. Blade too tight 2. Adjust blade
Page 8
Victor Garden Tools
EC DECLARATION OF CONFORMITY
We The Enterprise Department Ltd.
Of 11 Bridge Street, Bishop’s Stortford, Hertfordshire, UK. CM23 2JU
in accordance with the following Directive(s):
Machinery Directive 2006/42/EC
Lawn Mower
M
odel number: 9806 (RM001)
hereby declare that the equipment named above has been
designed to comply with the relevant sections of the above
referenced specifications. The unit complies with all applicable
Essential Requirements of the Directives.
Mr. Stuart Fowler
Imports Director
March 2014
Battery Disposal
The product contains a Lead acid battery which should not be disposed of with
general household waste. At the end of the product’s or battery’s life the
battery pack should be removed from the product and be disposed of properly
at a recycling facility.
For safety we do not recommend to dis-assemble and remove the battery from
the battery pack, and this should only be carried out by a professional or
technically competent person. It is recommended to dispose of the complete
battery pack at a recognised recycling facility.
ELECTRIC SCHEMATIC DIAGRAM
TECHNICAL DATA AND FEATURES
Rechargeable Lead-Acid Battery, 24V, 7AH
Charge Time: 24 hours
Cutting Path: 16in
W
orking Time: 45 minutes after full charge
No Load Speed: 1000RPM
Low Noise Operation
Cutting Capacity: 6000sq.feet per hour / 557.40m
2
per hour
5 Cutting Blades
Adjustable Cutting Height 13/16in - 2-3/16in
Safety Switch
Grass Catcher (25L capacity)
Features Battery Display, Automatic Power Off for Lower Battery
Wheel Size 10in (250mm)
Weight: 15.5kg with battery
Head Office, 11 Bridge Street,
Bishop’s Stortford CM23 2JU
Tel: 0844 482 4400
Fax: 01279 756595
www.coopersofstortford.co.uk
Loading...