Cooper Lighting Solutions WR-20 User Manual
FCC Compliance Statement
To assure continued FCC compliance:
1. Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the
equipment.
2. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator & your body.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
CAN ICES-3 (B)/NMB-3(B)
This equipment has been tested and tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does case harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warranties and Limitation of Liability
Please refer to www.cooperlighting.com for our terms and conditions.
Garanties et limitation de responsabilité
Veuillez consulter le site www.cooperlighting.com pour obtenir les conditions
générales.
Garantías y Limitación de Responsabilidad
Visite www.cooperlighting.com para conocer nuestros términos y condiciones.
WR-20
WaveLinx 20A Wireless Controllable Receptacle
Tamper Resistant
Specifications
Voltage 125VAC, 60Hz
Current 20A Maximum Load
Incandescent 960W
Ballast 500VA
Resistive 20A(2500W)
Motor 1 HP
Wireless Frequency 2.4 GHz
Operating Temperature 32-104° F, 0 -4 0° C
Range Up to 100 feet line of sight
Features
•
Wireless IEEE 802.15.4 technology creates a mesh network for command and control receptacle
•
Manual ON/OFF push button or remote control
•
Green/red color LED for status suitable for loads up to 20A
•
Simplified plug load control
•
Drag and drop programming via WaveLinx Mobile application
•
Supports overrides for Demand Response
•
Decorator style color matched wallplates
•
Provides power measurement reporting
•
Tamper-Resistant (TR)
Cooper Lighting Solutions
1121 Highway 74 South
Peachtree City, GA 30269
P: 770-486-4800
www.cooperlighting.com
2020 Cooper Lighting Solutions
©
All Rights Reserved
Printed in USA
Imprimé aux États-Unis
Impreso en los EE. UU.
Publication No. IB503017EN
April 2018
Cooper Lighting Solutions is a
registered trademark. All
are property
of their respective owners.
Cooper Lighting Solutions est une
marque de commerce déposée.
Toutes les autres marques de
commerce sont la propriété de leur
propriétaire respectif.
Cooper Lighting Solutions es una
marca comercial registrada. Todas
las marcas comerciales son
propiedad de sus respectivos
propietarios.
trademarks
Product availability, specifications,
and compliances are subject to
change without notice.
La disponibilité du produit, les
spécifications et les conformités
peuvent être modifiées sans préavis.
La disponibilidad de productos, las
especificaciones y los cumplimientos
están sujetos a cambio sin previo
aviso.
Description
The WR-20 wireless receptacle is an integral part of the WaveLinx Wireless Connected Lighting (WCL) System and
provides simplified wireless plug load control. Plug load control is required now in many building codes as part of
an energy saving control strategy. The wallbox mounted wireless duplex receptacle provides a constantly powered
bottom outlet and a wirelessly controlled top outlet. The NEMA wireless receptacle includes the NEMA symbol for
identifying a controlled receptacle as well as tamper resistant outlets for safety. The wireless receptacle operates on
a wireless mesh network based on IEEE 802.15.4 standards.
As part of the WaveLinx System, the wireless receptacle enables energy savings by turning OFF the top outlet when
the area is unoccupied. The wireless receptacle is automatically paired with all WaveLinx occupancy sensors in a
space when it is assigned to an area using the Wavelinx Mobile application. The wireless receptacle uses standard
AC power wiring and has an internal relay that will Open/Close the controlled outlet. The use of wireless control
features of WaveLinx reduces the wiring needed during installation. Use of the wireless control features of the
receptacle also includes power measurement capabilities that can be displayed in the WaveLinx Mobile application.
Warnings and Cautions
To be installed and/or used in accordance with appropriate electrical codes and regulations.
Exercise extreme caution when using remote controllable devices to control appliances.
Operation of the device may be in a different room than the controlled appliance, also an unintentional
activation may occur if the wrong button on the remote is pressed resulting in unwanted power on.
Controllable devices should never be used to supply power to, or control the On/Off status of medical
and/or life support equipment.
Dimensions
3.79”
3.26”
(96.50 mm)
(83 mm)
Installation Instructions
Wire Installation color guide
Black - Line
White - Neutral (N)
Green - Ground (G)
Ground wire must be wrapped
at least 2/3 to 3/4 around G
terminal screw and tightened.
Strip conductor insulation 3/4” (20mm)
Tighten terminal screws to 14 lbf-in
Use only 12 AWG copper or copper
clad wire with this device
1.68”
(42.79 mm)
1.96”
(50 mm)
Installation
This receptacle may be used in new installations or to replace an existing wall receptacle. Indoor use only.
WARNING:
TO AVOID FIRE, SHOCK ,OR DEATH ,TURN OFF THE POWER AT THE CIRCUIT BREAKER
BEFORE INSTALLING THIS RECEPTACLE.
1. Warning!: Verify power is OFF
before continuing.
2. For retrofit applications, remove
wall plate.
3. Remove the existing receptacle
from the box.
4. Disconnect the wiring from the
existing receptacle.
5. Connect the receptacle as shown
in the wiring diagram: Black lead
to hot wire, white lead to neutral
wire, green lead to ground wire.
6. Check connections to be sure
they are tight and no bare
conductors are exposed.
7. Insert the receptacle into the
outlet box carefully.
8. Attach the receptacle to the
box using supplied screws.
9. Attach the wall plate.
10. Restore power at the circuit
breaker and test the system.
Neutral
White
Ground
Green
Wiring Diagram
Line
Black
Insulation strip 3/4” (20mm)
in length.
Tighten terminal screws by turning
clockwise. After tightening always
test installed wires by pulling on
them to show they are securely
in place.
Either of the two “Line” and “N”
terminal holes can be used
during installation.
After stripping wire at 3/4”
(20mm) in length fully insert
wire and tighten.
Operations
Manual Switch
Button
Wirelessly Controlled
Receptacle
Red & Green LED
Indicator
Always-on
Receptacle
Basic Operation
The controlled outlet can be turned ON in two ways:
1. Manually by switch button located on receptacle from plate.
2. Top receptacle controller wirelessly by the WaveLinx Wireless Area Controller (WAC).
This receptacle may be used in new installations or to replace an existing wall receptacle.
Manual Control
The switch button on receptacle allows user to:
1. Manually turn the connected equipment ON or OFF by short pressing the button. When the LED indicator turns off means
controlled outlet is OFF. When the LED indicator turns green means controlled outlet is ON.
2. Manually put receptacle into pairing mode to Gateway by long pressing the button. When pairing mode is activated LED indicator
will flash red. Please note when putting receptacle into pairing mode will also reset the receptacle.
COOPER LIGHTING SOLUTIONS WaveLinx Wireless Controllable Receptacle Installation Instructions
COOPER LIGHTING SOLUTIONS
WaveLinx Wireless Controllable Receptacle Installation Instructions
32
Loading...