Cooper Lighting Solutions MST800LW, MST800L Instruction Manual

Questions?/

Des questions?/¿Preguntas? 1-800-334-6871 ConsumerProducts@

cooperlighting.com

Instruction Manual/Manuel d’instructions/Instrucciones

PACKAGING CONTENTS/ CONTENIDO DEL PAQUETE

A. Light fixture with 12 in. lead wire connector

Accesorio para la luz con conector de cable de 12 pulg
Luminaire avec fil de sortie et capuchon de connexion
de 30,5 cm (12 po)

MST800LW

MST800L

(Single head position)
(Posición de cabezal simple)
(Position à tête regroupée)

(Twin head position)
(Posición de cabezal doble)
(Position à tête séparée)

ENGLISH

ITEMS REQUIRED

(Purchase separately)

• Phillips screwdriver

HOW IT WORKS

During the daylight hours, the solar panel turns the sunlight
into energy that is stored in the rechargeable battery pack.
Your light features a motion sensor that turns the light ON
at night when motion is detected. This light is equipped
with a photocell, which only allows the fixture to turn ON
during the nighttime hours.

WARNINGS AND CAUTIONS

INSTRUCTIONS PERTAINING TO A RISK OF FIRE OR INJURY TO PERSONS.
To reduce the risk of fire or injury to persons, read and follow these instructions:

• DO NOT replace batteries.

• DO NOT dispose of this product in fire. Batteries inside this product may explode or leak.

• DO NOT puncture this battery pack. DO NOT work on this battery pack

• DO NOT disassemble fixture. The fixture does not have any user serviceable parts.

• For outdoor use only.

• Lithium-Ion batteries must be disposed of in accordance with local waste ordinances and
regulations.

• Do not operate a luminaire with a missing or damaged lens.

• Fixture is suitable for wall mount only. NOT suitable for ground mount installation.

• Do not cut the solar panel wire. Discontinue use if the wire becomes frayed or broken.

SAVE THESE INSTRUCTIONS.

FOR BEST RESULTS

• Allow fixture to receive four full days of sunlight before turning fixture ON.

• Locate solar panel in an area that will receive the
maximum amount of sunlight during the daylight
hours. Locate panel to receive at least 3-4 hours of
direct sunlight daily.

• Test your charged unit before permanently installing.

• Install the motion sensor 8-12 feet above the ground.
(Motion sensor is less sensitive above 12 feet.)

• Locate motion sensor so motion moves across the
detection zone (Fig. 1).

• Locate sensor away from heat producing sources to

• prevent false triggering. Also be very careful not to
include objects such as windows, white walls and
water in the detection zone.

Up to
70 feet

180 degrees

Fig. 1

• Locate sensor away from moving objects such as trees, large shrubs and street traffic.

• You will need to adjust the angle of the solar panel throughout the year as seasons change
in order to keep it at the best possible angle to the sun.

• Keep solar panel clear of any objects that will block the sunlight. It will be necessary to
periodically clean the solar panel with soft wet cloth.

• During periods of several cloudy days, the battery may fall below the operating level and
will need to be recharged with sunlight.

B. Solar panel with 15 ft. cord

Panel solar con cable de 15 pies
Panneau solaire avec cordon
de 4,6 m (15 pi)

D. (4) Solar panel mounting screws

(4) Tornillos de montaje
del panel solar
(4) Vis de montage de panneau
solaire

MOUNTING YOUR FIXTURE

1. Locate area in which you would like to install your

light fixture.

NOTE: For fixture to operate properly, the solar panel (B)
must be located in an area that will receive the maximum
amount of sunlight and is free from obstructions.

2. Using the fixture mounting screws (C) provided,

mount the snap-in mounting bracket (E) to a solid
surface 8-12 feet above the ground by placing the
screws through the center holes of the bracket.
Make sure the arrow on the bracket is pointing up.
(Fig. 2).

3. Slide fixture down over the snap-in mounting

bracket, making sure that the fixture engages the
guide ribs. Continue sliding down until the fixture

snaps into the locking tab.

4. Using the solar panel mounting screws (D) provided,

mount solar panel (B) to a solid surface (Fig. 3).
Adjust the angle of the solar panel (B) so that it will
receive the maximum amount of direct sunlight
during the daylight hours.

NOTE: For best results, locate panel to receive at least
3-4 hours of direct sunlight daily.

5. Carefully route the wire from the solar panel (B)

to the fixture (A) and plug it into the connector
extending from the side of the fixture housing (A)
(Fig. 4). Make sure to push the connector plugs
tightly together until you hear two clicks to ensure
they are fully engaged.

C. (2) Fixture mounting screws

(2) Tornillos de montaje del accesorio
(2) Vis de montage du luminaire

E. Snap-in mounting bracket

Soporte de montaje de sujeción
a presión
Support de montage encastrable

Fig. 2

E

Fig. 3

D

B

D

Fig. 4

A

D

C

C

D

B

1

ON OFF

Fig. 5

DURATION

1 min

Test 3 min

DURATION

1 min

Test 3 min

A

OPERATING YOUR FIXTURE

NOTE: Make sure you allow fixture to receive four full
days of sunlight before turning fixture ON.

1. Slide power switch ON.

2. Rotate knob on bottom of the sensor

to “TEST” (Fig. 5).

NOTE: Fixture has a warm up period of about one
minute. Light will turn on during this period. Once the
light turns off, you are ready to test.

3. Aim sensor toward the general direction in which

motion will occur. Always position the
sensor head with control switches facing toward

ON OFF

the ground.

4. Walk across the detection zone at the farthest distance you wish your sensor to

detect motion.

5. For more range, aim sensor slightly upward. For less range, aim sensor slightly downward.

Light will turn off 4 seconds after motion stops.

NOTE: Allow 5 seconds after light turns off before your next test.

6. Rotate knob on bottom of sensor to a duration up to 3 min. Light will turn ON at night

when motion is detected and turn OFF at the selected time interval after motion stops.

NOTE: When battery is low, the fixture will automatically turn OFF. (The fixture will not turn ON
until the battery has recharged to the operating level.) The red LED indicator light will blink
every 5 seconds at night until the battery is charged to the operating level.

PROPER BATTERY CARE

NOTE: Proper care should ensure the longest possible life for your battery.

• Make sure that your solar panel is located in a sunny location.

• When battery is low, the fixture will automatically turn OFF. (The fixture will not turn ON until
the battery has recharged to the operating level.) The red LED indicator light will blink every
5 seconds at night until the battery is charged to the operating level.

• To ensure proper recharge, slide power switch OFF and allow fixture to receive 4 full days of
sunlight before turning the fixture ON.

TROUBLESHOOTING

Problem Cause / Solution

Light Does Not
Come On With
Motion At Night

Light Comes On

For No Apparent
Reason At Night

Light Stays On At
Night And Does
Not Turn Off

Light Is On
During The Day

Surrounding external ambient light is too bright. (If so, the unit may
think it is daytime.)

• Re-aim the head.

• Relocate or reposition the unit away from the light source.

Fixture is not charging during the day.

• Solar panel must be connected to the connector extending
from the side of the fixture housing when charging.

• Solar panel must be receiving direct sunlight to charge during
day (reposition if shadowed).

• Solar panel must be clean and free from debris.

• Make sure batteries have been charged for 4 full days of
sunlight prior to turning the fixure ON.

• When battery is low, the fixture will automatically turn OFF until
the battery is charged to the operating level.

There is motion in the detection zone.

• Make sure the sensor is not picking up moving objects such as
trees, traffic, etc.

TEST FOR YOURSELF.

• Cover the sensor lens with black electrical tape to prevent
sensor from detecting motion. If the light stays off, something in
the detection zone is triggering the sensor.

• Reposition the sensor.
* If the light stays on with the sensor lens covered, contact

customer service.

There is motion in the detection zone.

• Make sure the sensor is not picking up moving objects such as
trees, traffic, etc.

• Reposition motion sensor.
* If the light continues to stay on, contact customer service.

The knob on the bottom of the motion sensor is in the TEST mode.

• Rotate the knob to a duration up to 3 min.

The motion detector is shadowed.

• Reposition motion sensor.

1-YEAR LIMITED WARRANTY

THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Cooper Lighting Solutions ("CLS") warrants to customers that, for a period of one year from
the date of purchase, CLS

products will be free from defects in materials and workmanship.
The obligation of CLS under this warranty is expressly limited to the provision of replacement
products. This warranty is extended only to the original purchaser of the product. A
purchaser’s receipt or other proof of date of original purchase acceptable to CLS. This is
required before warranty performance shall be rendered. This warranty does not apply to CLS
products that have been altered or repaired that have been subjected to neglect, abuse,
misuse or accident (including shipping damages). This warranty does not apply to products
not manufactured by CLS which have been supplied, installed, and/or used in conjunction with
CLS products. Damage to the product caused by replacement bulbs or corrosion or
discoloration of brass components are not covered by this warranty.
LIMITATION OF LIABILITY:
IN NO EVENT SHALL CLS BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT,
STRICT LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR SHALL
THE LIABILITY OF CLS FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR CONNECTED WITH
THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE, MAINTENANCE, REPAIR OR
MODIFICATION OF CLS PRODUCTS, OR SUPPLY OF ANY REPLACEMENT PARTS THEREFORE,
EXCEED THE PURCHASE PRICE OF CLS PRODUCTS GIVING RISE TO A CLAIM. NO LABOR
CHARGES WILL BE ACCEPTED TO REMOVE OR INSTALL FIXTURES.
To obtain warranty service, please contact CLS, at 1-800-334-6871, press option 2 for
Customer Service, or via e-mail [e-mail] and include the
following information:

• Name, address and telephone number

• Date and place of purchase

• Catalog and quantity purchase

• Detailed description of problem
All returned products must be accompanied by a Return Goods Authorization Number issued
by the Company and must be returned freight prepaid. Any product received without a Return
Goods Authorization Number from the Company will be refused. CLS is not responsible for
merchandise damaged in transit. Repaired or replaced products shall be subject to the terms
of this warranty and are inspected when packed. Evident or concealed damage that is made
in transit should be reported at once to the carrier making the delivery and a claim filed with
them.

Reproductions of this document without prior written approval of CLS are strictly prohibited.

or assistance, call 1-800-334-6871 or e-mail us at [e-mail]

F

Printed in China

ESPAÑOL

ARTÍCULOS NECESARIOS

(se compran por separado)

• Destornillador en cruz (Phillips)

CÓMO FUNCIONA

Durante las horas del día, el panel solar transforma la luz
solar en energía que queda almacenada en el paquete de
la bateríarecargable. Su luminaria cuenta con un sensor
de movimiento, que enciende la luz cuando es de noche
y se detecta algún movimiento. Esta luminaria está
equipada con una fotocélula, que sólo permite que el
artefacto se encienda durante las horas de la noche.

180 grados

ADVERTENCIAS Y PRECAUCIONES

INSTRUCCIONES CONCERNIENTES AL RIESGO DE INCENDIO O LESIONES A
LAS PERSONAS:

ATENCIÓN: Para reducir el riesgo de incendio o lesiones personales:

• NO sustituya las baterías.

• NO deseche este producto por medio de métodos combustibles. Las baterías que se

encuentran dentro de este producto pueden explotar o tener pérdidas.Atienda todas
las advertencias.

• NO perfore este pack de baterías. NO trabaje sobre este pack de baterías.

• NO desarme la luminaria. La luminaria no contiene piezas que puedan recibir un servicio de

mantenimiento por el usuario.

• Para uso en exteriores solamente.

• Las baterías de ión de litio deben desecharse de conformidad con las ordenanzas y

normas locales sobre disposición de desechos.

• No ponga en funcionamiento esta luminaria si le falta la lente o está dañada.

• La luminaria es apta para un montaje en paredes solamente. NO es apta para su instalación

por medio de su montaje en el suelo.

• No corte el cable del panel solar. Discontinúe su uso si se pela o rompe el cable.

GUARDE ESTAS INSTRUCCIONES.

Hasta
70 pies

2