Cooper Lighting Solutions IB520023ML, LDSQ4B, LDSQ6B, Portfolio Installation Instructions

INS #

Brand Logo
reversed out of
black

INS #

697916

TM

IB520023ML

INS #

Installation Instructions – LDSQ4B/LDSQ6B Series Recessed LED
Tr ims
Instructions d’installation – Garnitures à DEL en retrait de la série
6LSQA
Instrucciones de instalación – Terminaciones para LED empotrados
de la serie 6LSQA

IMPORTANT: Read carefully before installing fixture.
Retain for future reference.

WARNING

Risk Of Electrical Shock! Disconnect power at fuse or
circuit breaker before installing or servicing.

WARNING

Risk Of Fire! Do not install insulation within 3 inches
(76 mm) of any part of the luminaire fixture or in a
way that may entrap heat.

WARNING

Installation and servicing to be performed only
by qualified personnel. If not qualified, consult an
electrician.

WARNING

Do not energize the LED Engine until the protective
covering has been removed and the lower trim
properly installed. Do not touch the yellow surface of
the LED as it may damage the light engine.

SAFETY: When using electrical equipment, basic safety
precautions should always be followed, including the
following:

1. This unit is for recessed mounting only. Do not use in
hazardous locations nor near gas or electric heaters.

2. Do not use this equipment for other than the intended
use.

3. Install only in accordance with National Electrical Code
and local regulatory agencies’ requirements.

4LBSQ 4LBSQLWW 4LBCSSQ 4LBPSSQ

6LBSQ 6LBSQLWW 6LBCSSQ

Installation Instructions – LDSQ4B/LDSQ6B Series Recessed LED Trim

INSTALLATION

1. Place end of flexible conduit through frame opening
in ceiling exposing upper portion of quick disconnect
(Figure 2.).

2. Remove LED engine from protective packaging.

3. Remove trim assembly from protective packaging and
rotate side clips (3) outwards. (Figure 4.).

4. Insert LED engine on to trim assembly. Align post on
LED engine with slot on trim assembly (Figure 5.)

5. Rotate side clips (3) into place to securely attach trim
assembly to LED engine (Figure 6.).

6. Trim ring (optional) should be placed between the
ceiling and lower trim.

7. Properly align the connector as shown in (Figure 7.).
Plug in the luminaire quick disconnect on the module.

8. Ensure the connector is properly engaged. (Figure 8.).

9. Install the LED engine and trim assembly by inserting
the torsion springs into the spring receivers located
inside the housing (Figure 9.).

Trim Assembly

Figure 3

Figure 4

LED

Engine

Torsion
Springs

Side Clips

Height Adjustment
Thumb Screw

Rotational
Adjustment Thumb
Screws

Figure 1

Square Neck

Figure 2

Luminaire
Quick
Disconnect

Junction Box

Figure 5

Figure 6

2

Installation

Instructions – LDSQ4B/LDSQ6B Series Recessed LED Trim www.cooperlighting.com

Installation Instructions – LDSQ4B/LDSQ6B Series Recessed LED Trim

Cleaning

To Clean Trims:

1. Press in on white plastic latch to remove upper
reflector and clean lens. (Figure 10 & 11.)

2. Gently wipe with soft, clean, dry lint-free cloth to

remove dust.

3. Wipe with mild detergent solution on a soft, clean

cloth to remove fingerprints and stains.

4. Rinse with clean water and dry with soft, clean, dry
lint-free cloth.

Figure 7

Figure 8

White

Plastic Latch

Figure 10

Upper Reflector

Lens

Figure 9

Figure 11

Installation Instructions – LDSQ4B/LDSQ6B Series Recessed LED Trim

www.cooperlighting.com

3