Cooper Lighting Solutions IB510151EN Installation instructions

Brand Logo
reversed out of
black

IB510151EN

INS #

INS #

LumenSafe

Installation instructions – LumenSafe Wi-Fi Video Retrieval

WARNING

Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards- Installation and maintenance of this
product must be performed by a qualified electrician. This product must be installed in accordance
with the applicable installation code by a person familiar with the construction and operation of the
product and hazards involved.

Risk of Fire and Electric Shock- Make certain power is OFF before starting installation or attempting
any maintenance. Disconnect power at fuse or circuit breaker.

Risk of Fire- Refer to product label for specific minimum supply conductor requirements.

Risk of Burn- Disconnect power and allow fixture to cool before handling or servicing.

Risk of Personal Injury- Fixture may become damaged and/or unstable if not installed properly.

Failure to comply with these instructions may result in death, serious bodily injury and property damage.

DISCLAIMER OF LIABILITY: Cooper Lighting Solutions assumes no liability for damages or losses of any kind
that may arise from the improper, careless, or negligent installation, handling or use of this product.

NOTICE: Green ground wire provided in proper location. Do not relocate.
ATTENTION Receiving Department: Note actual fixture description of any shortage or noticeable damage on

delivery receipt. File claim for common carrier (LTL) directly with carrier. Claims for concealed damage must be
filed within 15 days of delivery. All damaged material, complete with original packing must be retained.

Safety: This fixture must be wired in accordance with the National Electrical Code and applicable local codes and
ordinances. Proper grounding is required to insure personal safety. Carefully observe grounding procedure under
installation section.

APPLICATIONS: This lighting fixture is designed for outdoor lighting services, and should not be used in area
of limited ventilation or inside high ambient temperature enclosures. It must be stored in a dry location prior to
installation. Do not expose lighting fixture to rain, dust or other environmental conditions prior to installation
and insertion of photo control or shorting cap (if so equipped). Best results will be obtained if installed and
maintained according to the following recommendations.

Installation instruc tions – LumenSafe Wi-Fi Video Retr ieval

REGULATORY INFORMATION

47 CFR Part 15 Regulation Class A Device

ote: N This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.

This equipment complies with radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20 cm between the radiator and your body.

Industry Canada

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:

1) This device may not cause interference; and

2) This device must accept any interference, including interference that may cause undesired operation of the device.

This radio transmitter IC: 4706A-LMSWFG has been approved by Innovation, Science and Economic Development Canada
to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in
this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this
device.

FCC and IC Antenna Requirements Toward License Exempt Radio Transmitters (WLAN)

The license-exempt WLAN radio transmitter contained in this equipment may only be operated with an antenna of a type, a
maximum gain and the required antenna impedance as approved and specified below. To reduce potential radio interference
to other users, choose the antenna type and it’s gain so that the equivalent isotropically radiated power (EIRP) is not more
than that necessary for successful communication.

Wi-Fi Antenna Requirements/Specs

Category Description

Frequency Range 2.4 GHz

Antenna Type Low Profile Housing PCB Antenna

Impedance 50 Ohms

VSWR 1.5:1 or less at resonant point

Peak Radiated Gain 4 dBi

Radiation Omni-directional

Polarization Vertical

Connector RP-SMA(M)

2

Cooper Lighting Solutions IB510151EN Installation instructions