Cooper Lighting Solutions IB505006EN Installation Manual

IB505006EN 049-263

Installation Instructions for the Sure-Lites SEL Emergency Lights
with Remote Capacity

INS #

Sure-Lites

WARNING

Risk of Fire/Electric Shock

If not qualified, consult an electrician.

Important Safeguards

WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE OBSERVED INCLUDING
THE FOLLOWING.

1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS

2. Do not use outdoors.

3. Do not use in hazardous locations, or near gas or electric
heaters.

4. Do not let power supply cords touch hot surfaces.

5. Use caution when servicing batteries. Battery acid can
cause burns to skin and eyes. If acid is spilled on skin or in
eyes, flush acid with fresh water and contact a physician
immediately.

6. Do not use this equipment for other than the intended use.

7. Installation is to be performed only by qualified personnel.

8. Install in accordance with National Electric Code and local
regulatory agency requirements.

9. The use of accessory equipment not recommended by the
manufacturer may cause an unsafe condition.

10. Equipment should be mounted in locations and at heights

where it will not readily be subjected to tampering by
unauthorized personnel.

11. SAVE THESE INSTRUCTIONS

MAX MOUNTING HEIGHT:

17.24 FT for SEL25 models

25.39 FT for SEL50 models

27.6 FT for SEL60 models

WARNING

Risk of Electric Shock

Disconnect power at fuse or circuit breaker before
installing or servicing.

INSTALLATION

1. De-energize the circuit at the junction box (J-box) where
the emergency light is to be installed.

2. Open the emergency light by inserting a screwdriver in the
two slots at the bottom of the unit, then tipping the cover
up off of the backplate.

3. To mount to a junction box - Drill out the appropriate
mounting pattern and the wire pass hole in the backplate
to fit the J-box being used.

4. To mount to conduit – Cut out the U shaped knockout on
the cover using snips, then attach the 1/2” conduit hub to
the backplate.

5. Once the backplate is secured, the housing can be held in
place during installation using the EZ Hang feature. (see
Fig. 1)

6. Connect the incoming wires to the fixture’s power supply
wires using the wire nuts provided. Connect the white
wire to neutral. If using 120V, connect the black wire to the
hot lead. If using 277V, connect the orange wire to the hot
lead. Cap the unused lead. Secure the emergency light
to the wall and/or junction box using installer supplied
hardware.

7. Connect the battery to the PCB. See schematic for detail.

8. Snap the cover onto the backplate.

9. Energize AC supply. The test button should illuminate, and
LED heads will illuminate briefly when the test button is
pushed.

10. If the unit has remote capacity, LED remotes can be
connected using the violet (+) and yellow (-) wires. See
schematic.

11. Adjust the heads as needed.

12. If the fixture is to be powered down for an extended
period after initial installation, replace the EZ Key. This
will prevent the battery from discharging when AC power
is removed. However, it will also prevent the battery
from charging when AC power is restored, so it must be
removed once the unit is ready for regular operation.

IB505006EN

OPERATION

Depress the test switch. The
charge LED will extinguish. LED heads will illuminate as long as
the button is pushed. Release the test switch. The charge LED
will illuminate and the LED heads will turn off.

LED heads will remain lit and the

MAINTENANCE

None required. Replace the batteries as needed according
to ambient conditions. However, we recommend that the
equipment be tested regularly in accordance with local codes.

NOTE: Servicing of any parts should be performed by qualified
personnel. Only use replacement parts supplied by Cooper
Lighting Solutions.

CAUTION: This equipment is furnished with a sophisticated low
voltage battery dropout circuit to protect the battery from over
discharge after its useful output has been used. Allow 24 hours
recharge time after installation or power failure for 90 minute
testing.

TROUBLE SHOOTING GUIDE

If LED heads or charge indicator LED does not illuminate, check
the following:

1. Check AC supply – verify that unit has 24 hour AC supply.

2.. Unit is shorted or battery is not connected.

3.. Battery discharged. Permit unit to charge for 24 hour s and
then re-test.

4.. If following the abo ve trouble shooting hints does not
solve your problem, contact your local Cooper Lighting
Solutions representative for assistance.

Figure 1

Slide snaps through holes
in housing for temporary
mount when wiring.

Warranties and Limitation of Liability

Please refer to www.cooperlighting.com for our terms and
conditions.

SCHEMATICS

Remote Heads if
Applicable

Battery

+

-

JK4

+

JK5

-

R5

JK3

D4

D3

R17

JK2

+

-

c

R2

+

R6

-

Q5

C2

R12

+

­Q3

RMT

F2

U2

R18

R14

R7

R10

Q4

R15
R16

Q2

CN3

LAMPS

CN2

277120N

R4

R11

R3

R13

C3

+

MOV2

R9

C1

CN1

D2

BATT

U1

D8

J1

R8

MOV1

F1

JK1

CN4

D5

SW1

LED1

D1

D6
D7

Q1

LED/SW

D9

R1

Base Heads -

ORANGE - 277VAC
BLACK - 120VAC
WHITE - NEUTRAL

Mounted on Fixture

SEL with Remote Capacity and Base Heads

Cooper Lighting Solutions

1121 Highway 74 South
Peachtree City, GA 30269

www.cooperlighting.com

Remote Heads if
Applicable

Battery

+

-

JK4

+

JK5

-

R5

JK3

D4

D3

R17

JK2

+

-

c

R2

+

R6

-

Q5

C2

R12

+

­Q3

RMT

F2

U2

R18

R14

R7

R10

Q4

R15
R16

Q2

CN3

LAMPS

CN2

277120N

R4

R11

R3

R13

C3

+

MOV2

R9

C1

CN1

D2

BATT

U1

D8

J1

R8

MOV1

F1

JK1

CN4

D5

LED1

SW1

D1

D6
D7

Q1

LED/SW

D9

R1

Higher Power Heads

ORANGE - 277VAC
BLACK - 120VAC
WHITE - NEUTRAL

- Mounted on Fixture

SEL with Remote Capacity and Higher Power Heads

Cooper Lighting Solutions

© 2020
All Rights Reserved
Printed in USA
Publication No. IB505006EN

Cooper Lighting Solutions is
registered
All trademarks are
of their respective owners.

trademark.

a

property