Cooper Lighting Solutions EG2-NA Installation Instructions
Installation Instructions
EG2-NA Ethernet Gateway
Model # EG-2-NA
INS #
Contents
INTRODUCTION .............................3
Specification .....................................3
Dimensions ......................................3
Weight ........................................3
Product Overview .................................3
Mounting ......................................... 4
Location and spacing ...............................4
Ambient atmosphere requirements ...................4
Mounting Holes ...................................4
Supply Wiring ...................................... 4
Connecting the Supply .............................4
Control Wiring ..................................... 4
iCAN Network ....................................4
Wire Gauge for Supply Terminals .....................4
iCAN Connectors ..................................5
WARNING
WARNING HAZARDOUS VOLTAGES, DISCONNECT FROM SUPPLY BEFORE REMOVING COVERS
NO USER SERVICEABLE PARTS INSIDE SERVICE BY QUALIFIED PERSONNEL ONLY
Setup Instructions .................................. 5
Ethernet Network .................................5
Configuration ...................................... 5
iCAN Device Number ..............................5
Factory Default IP Settings ..........................5
Power Up ........................................5
Setting the IP Address ..............................5
PC Node Method ..................................6
Ethernet Port Method ..............................6
Reset to Factory Defaults ...........................6
WARRANTIES AND LIMITATION OF LIABILITY ........... 7
SAFETY INSTRUCTIONS
IMPORTANT SAFEGUARDS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
The EG2-NA is built and tested to strict safety regulations. By following the steps listed below and elsewhere within this
guide, you can ensure safe installation and operation of these controller units.
The EG2-NA must be installed only by a qualified electrician
The installation must comply with the appropriate electrical codes and regulations in force in your area.
The EG2-NA is designed for indoor installation and use only.
Ensure that all wiring used conforms fully to local specifications and is sufficiently rated for the installation.
All new wiring must be fully verified before applying power.
The high voltage supply should be fed to the EG2-NA via an external isolation breaker with sufficient capacity for the
planned installation.
Ensure that the supply is fully isolated at an external breaker before removing the chassis covers. Test that power has been
removed before starting to handle conductors.
Ensure that high voltage and low voltage wiring remains separate.
SAVE THESE INSTRUCTIONS
2
EG2-NA Ethernet Gateway
www.cooperlighting.com
Introduction
Introduction
The Ethernet Gateway provides a connection between an
iLumin lighting control network and an Ethernet Local Area
Network, either through an Ethernet switch or wireless
router.
The EG2-NA acts as a host for the iLumin series of
remote applications including iOS (iPhone/iPod Touch/iPad
& Android OS devices). Coupling the EG2-NA to a Wi-Fi
network enables secure scene control, visual feedback and
modification from your hand held device. Once configured,
the EG2-NA automatically loads room and scene information
to the connected hand held device.
In addition to its handheld device capability, the EG2-NA
houses internal webserver pages that allow for basic scene
control functions. These internal pages are accessed
through an internet browser and are password protected for
security.
The EG2-NA also facilitates the commissioning of the
iLumin system, allowing our factory trained technicians to
use the EG2-NA connection to configure the iLumin system
using iCANsoft on a LAN or Wi-Fi enabled PC or via the
internet rather than by connecting directly into the iLumin
network.
Specification
Unit requires 120-240 VAC 50/60 Hz 0.45A 1Ø Maximum
iCAN network connection
Ethernet connection is fully transformer isolated
Ambient temperature range 32°F to 104°F
(0°C to 40°C)
Humidity 20% to 90% non-condensing
Configuration and sequence memory
Field upgradable FLASH program memory
Internal +15 VDC, 2A power supply
Dimensions
Weight
Packed: 5.7 lbs. (2.6 kg)
Unpacked: 5.3 lbs. (2.4 kg)
Product Overview
6
5
1
2
3
4
EG2-NA Ethernet Gateway
1. Ethernet Connection
2. Reset Button
3. Main Supply Terminal
4. Power Supply
5. CAN ID Button
6. Block iCAN Network Connector with a green (power)
and yellow (network activity) LED
www.cooperlighting.com
3
Loading...