Cooper Lighting STS7A30SFM1XG User Manual

174 STREETWORKS Outdoor Lighting Solutions Cooper Lighting

20'—39' MOUNTING HEIGHT

STS SQUARE TAPERED STEEL

POLES

1

...

ASTM Grade steel base plate with ASTM A366 base cover.

2

...

Hand hole assembly 3" x 5" on STS poles.

3

...

Steel shaft 55,000 PSI. Shot blasted and painted with
polyester powder coat.

4

...

Drilled or Tenon (specify).

5

...

Anchor bolt per ASTM A576 with (2) nuts, (2) flat washer,
and (1) lock washer. Nuts, washers and threaded portion
of bolt are hot dip galvanized. 3" hook for 3/4" bolt.
4" hook for 1" bolt.

SPECIFICATION FEATURES

FOUR BOLT ANCHORAGE [See ordering information]

BC=Bolt Circle
BP=Bolt Projection
AB=Bolt Dimensions
D=Bolt Diameter
H=Bolt Dimensions

FINISH COLORS [See ordering information]

F=Dark Bronze
G=Galvanized
V=Grey
W=White
Y=Black

1

5

2

3

4

WARNING: THE USE OF UNAUTHORIZED ACCESSORIES SUCH AS BANNERS, SIGNS OR PENNANTS FOR WHICH THE POLE WAS NOT DESIGNED FOR VOIDS THE COOPER LIGHTING

WARRANTY AND MAY RESULT IN POLE FAILURE CAUSING SERIOUS INJURY OR PROPERTY DAMAGE. COOPER LIGHTING'S POLE WARRANTY IS ALSO VOIDED IF
LUMINAIRE IS NOT INSTALLED AT TIME OF POLE INSTALLATION.

MH

(mounting height)

B

S

D

H

handhole

12 5/16 "

Base View

BC

BP

AB

STREETWORKS Outdoor Lighting Solutions 175Cooper Lighting

SQUARE TAPERED STEEL POLES

Mounting Fixture No. & Accessories

Shaft

3

Wall Height Base Mounting Location Arm (Ground

Square Straight Steel Size Thickness (ft.) Type Finish & Type of Arms Lengths Lug)

ST S7 A 30 SFM 1 XG

Bolt Anchor

Base Circle Bolt Shaft Bolt Net. Max. Fixture

Mtg. Catalog

1, 2

Wall Square Dia. Proj. Size Dia. &. Wt. EPA (Sq. Ft.)

4

EPA (Sq. Ft.)

4

Load—Include

Height Number Thickness (In.) (In.) (In.) (In.) Length (In.) (Lbs.) At Pole Top 2' Above Pole Top Bracket (Lbs.)

MH S BC BP B AB 80 90 100 80 90 100

20 STS6A20SF .120 Consult your Cooper Lighting Representative
25 STS6A25SF .120 Consult your Cooper Lighting Representative
30 STS7A30SF .120 Consult your Cooper Lighting Representative
30 STS7D30SF .180 Consult your Cooper Lighting Representative
35 STS8A35SF .120 Consult your Cooper Lighting Representative
39 STS8A39SF .120 Consult your Cooper Lighting Representative

NOTES: 1 Catalog number includes pole with anchor bolts with double nuts (BEFORE INSTALLING ANCHOR BOLTS MAKE SURE PROPER ANCHOR BOLT TEMPLATE IS OBTAINED FROM COOPER LIGHTING HEADQUARTERS).

2 Tenon size or machining for rectangular arms must be specified. Hand hole is located 180° from single arm.
3 Shaft size, base plate, anchor bolts and projections may vary slightly—all dimensions nominal.
4 EPAs based on shaft properties with wind normal to flat. EPAs calculated using base wind velocity as indicated plus 30% gust factor.

MACHINING FOR RECTANGULAR ARMS [Add as suffix]

Designation Designation Designation Quantity
Letter & Number Letter & Number Letter & Number & Location

M1 E1 Z1 Single
M2 E2 Z2 2 @ 180°
M3 E3 Z3 3 @ 120°
M4 E4 Z4 4 @ 90°
M5 E5 Z5 2 @ 90°

NOTES: Refer to Fixture Drilling Options on page 160.

ACCESSORIES

A=1/2" tapped hub

1

B=3/4" tapped hub

1

C=Convenience outlet

2

G=Grounding lug (max. wire #8 AWG)
H=Additional hand hole and cover—

12" below pole top—90° from hand hole.

NOTES: 1 Location is 3' above base–90° from hand hole.

2 Outlet is located 4' above base and on same side of pole

as hand hole, unless specified otherwise. Receptacle not
included, provision only.

MOUNTING OPTIONS [Add as suffix]

Fixed Tenon Designation O.D. Length

Number (In.) (In.)

1 2 3/8 3 1/2
2 2 3/8 4
3 3 1/2 5
934

DRILLING PATTERN

Type “M” [RCL, Landau, Galleria and Vision] Type “E” [Concourse III] Type “Z” [Credenza and Cirrus]

9/16" [14mm]

dia. hole (3)

4 7/8" [124mm]

4" [102mm]

2 7/16" [62mm]

ORDERING INFORMATION
SAMPLE NUMBER: STS7A30SFM1XG

NOTE: Specifications and dimensions subject to change without notice.

2 13/16''

7/8''

3 7/8''

3/4'' dia.
hole

(2) 3/8"
dia. holes

2 7/16''

2 5/16''

4 7/8''

3/4'' dia.
hole

(2) 5/8''
dia. holes

O.D.

LENGTH