Page 1
INSTA
LLATION INSTRUCTIONS
V
90168
A
QUIET CEILING REMODEL W/ROUND TRI
odel: QCM504RM with QCM5001-5004
M
Avoid Fire or Electric Sho
*Installation Instructions for
*Install per Nati
*Read Installation Instructions completely before installation.
*Failure to follow Installation Instructions may void warranties.
INSTALLATION CODE BY A PERSON FAMILIAR
WITH THE CONSTRUCTION AND OPERATION O
HE PRODUCT AND THE HAZARDS INVOLVED
T
Pre-Insta
1. Check for Above Ce
2. Make 7-1/4" diameter Cutout in Ce
onal Electrical C
THIS PRODUCT MUST BE INSTALLED IN
ACCORDANCE WITH THE APPLICABL
llation Preparati
Above Ce
qualified electricians only
ode and local r
iling Clearance of 5-1/2". See Fig. 1
iling. See Fig. 1
iling Clearanc
e
ck
.
egulations
E
on
.
.
F
.
.
M
C
Electrical Connection (Con't
To Existing Electrical Service
J-Box
Flex Cable
Transformer Assy
Figure 2
)
U
R
L
U
S
Lamp
Socket
Wiring
Fixture
Ceili
ng
7-1/4
"
Cutout
5-1/2
"
Figure 1
Electrical Connection
1. Turn OFF Electrical Service.
2. All
appropriate electrical "rough" wiring should be completed.
3. C
onnect wiring inside J-Box (See Fig. 2) to Existing Electrical Service
thr
ough Knockout provided
NOTE: Single circuit cable only
jumper. Wire single fixture or wire thr
fixture) in J-Box
4. Carefully insert wired J-Box, Transformer Assembly, Flex Cable
Lamp Socket thr
cutout) avoiding all insulation and combustable surfaces by 3" all around
.
ough Ceiling Cutout into available ce
.
and/or single fixture with next fixture
ough with second cable (to nex
iling area (around
t
and
.
Insta
1. Remove factory installed Wiring Access Door on Fixture. See Fig. 3.
Retain Wing Nuts and Door for re-installation
2. Fold three (3) Rotati
4) making sure Brackets are in
(See Fig. 5) to accomm
3
. Insert Fixture into Ce
Aperture to desired position relative to adjacent wall(s), other fixtures,
aperture alignments, etc.
4. OPTIONAL: Retain orientation by installing two (2) or three (3)
drywall/zip screws into outer perimeter of Perforated Mudding Frame
5. Holding Fixture firm to ceiling surface, drive clockwise the three (3) #8 x
3" Set Screws (See Fig. 5) located on the
M
udding Frame (See Fig. 6) to rotate and lock the Rotational Clamp
Brackets to the ceiling. DO NOT overtighten the Screws or Rotational
Clamp Brackets. (Overtightening may crack ceiling material.)
6. Reach inside
Lamp Socket, Flex Cable, J-Box/Transformer Assembly. See Fig. 6.
7. Pull Lamp Socket
8. Slide C
O
pening
9. Re-install Wiring Access Door over C
Nuts removed earlier
llation Of Housi
onal Clamp Brackets tight against Fixture (See Fig.
upper most (highest) thr
odate largest ceiling thickness.
iling Cutout (See Fig. 1), rotating to orient S
and through Fixture Wiring Access Opening and locate
and Lamp Wiring into inside of Fixture. See Fig. 6.
onduit Ring (See Fig. 6) into Slot (See Fig. 5) in Wiring Access
.
.
ng
.
eaded position
quare
.
underside of Perforated
onduit Ring. Secure with Wing
RSA Lighti
ng
7945 Orion Ave, Van Nuys, CA
Visit our web site at:
91406
818-349-3030/ 800-356-3030
www.rsalighting.com
FAX
818-349-3031
Page 2
Loading...