PQS45
Instruction Manual
Instrucciones
Directives
All manuals and user guides at all-guides.com
all-guides.com
Call for customer service and/or missing or damaged parts (800-334-6871)
English
PQS45
2
Congratulations. You have purchased a 500 watt portable worklight. This light is
perfect for those applications where a wide concentration of light is needed. Use it to
light the entire working area around any inside or outside project that you might have.
WHAT YOU NEED
• Screwdriver
WHATʼS INCLUDED
• Light head (A)
• (2) 500 watt quartz halogen bulbs (B)
• Safety guard (C)
• Stand (D)
• Handle (E)
• Light bracket (F)
• (4) Lock washers (G)
• (4) Regular washers (H)
• (2) Short bolts (I)
• (2) Long bolts (J)
• (2) Spacers (K)
• (2) Light head knobs (L)
• (4) Screws (M)
WHAT TO KNOW
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK,
EXPOSURE TO EXCESSIVE UV RADIATION OR INJURY TO PERSONS.
IMPORTANT SAFETY INSTRUCTIONS.
Lighted lamp is HOT!
WARNING: To reduce the risk of FIRE, ELECTRIC SHOCK, EXPOSURE
TO EXCESSIVE UV RADIATION OR INJURY TO PERSONS:
• Turn off/unplug and allow to cool before replacing bulb (lamp).
• Bulb (lamp) gets HOT quickly! Only contact switch/plug when turning on.
• Do not touch hot lens, guard or enclosure.
• Do not remain in light if skin feels warm.
• Do not look directly at lighted lamp.
• Keep away from materials that may burn.
• Use only with a 500 watt or smaller bulb (lamp).
• Do not touch the bulb (lamp) at any time. Use a soft cloth. Oil from skin may
damage bulb (lamp).
I
J
M
G
H
K
L
A
B
C
D
E
F
All manuals and user guides at all-guides.com
Call for customer service and/or missing or damaged parts (800-334-6871)
3
• Do not operate the portable luminaire with a missing or damaged guard, lamp
containment barrier (lens) or UV filter.
• If lens is replaced, use only a diffused tempered safety glass of equal thickness.
• Use of bulb(s) of higher wattage rating than what is listed in the safety instructions
will void the warranty.
• Dissassembly of the fixture will void the warranty.
• Fixture must be connected to a 120 Volt, 60 Hz power source. Any other
connection voids warranty.
• The electrical system, and the method of electrically connecting the fixture to it,
must be in accordance with the National Electrical Code and local building codes.
• For indoor and outdoor use.
• cULus Listed.
WARNING: When using outdoor use portable luminaires, basic safety
precautions should always be followed to reduce the risk of fire, electric
shock, and personal injury, incuding the following:
Read all instructions.
• Use only three-wire outdoor extension cords that have three-prong grounding plugs
and grounding recptacles that accept the applianceʼs plug.
• Ground Fault Circuit Interrupter (GFCI) protection is to be provided on the circuit(s)
or outlet(s) to be used for the wet location portable luminaire. Receptacles are
available having built-in GFCI protection and are able to be used for this measure
of safety.
• Use only with an extrension cord for outdoor use, such as an extension cord of
cord type SW, SW-A, SOW, SOW-A, STW, STW-A, STOW, STOW-A, SJW, SJW-A,
SJOW, SJOW-A, SJTW, SJTW-A, SJTOW, SJTOW-A.
SAVE THESE INSTRUCTIONS.
ASSEMBLING YOUR FIXTURE
WARNING: Deviation from the assembly instructions may result in a
risk of fire or electric shock.
1. Attach light head (A) and handle (E) to the light
bracket (F). This step will require using the
(2) long bolts, (2) lock washers, (2) spacers,
(4) regular washers and (2) light head knobs
(Fig. 1).
2. Attach the light bracket (F) to the stand (D) using (2) short bolts.
3. Attach handle to light fixture using 4 screws.
4. Install the grille guard (C) in the light fixture by inserting one side of the guard
between the frame and the lens. Squeeze the guard until the other side can be
placed between the opposite side of the frame and lens.
Fig. 1
All manuals and user guides at all-guides.com
Call for customer service and/or missing or damaged parts (800-334-6871)
4
AIMING THE FIXTURE
WARNING: Risk of burn. Disconnect power and allow fixture to cool
before changing bulb or handling fixture.
Note: For maximum bulb life, position light so that the quartz
halogen bulb remains within 4 degree of horizontal (Fig. 2).
Make sure the light fixture is in the OFF position and cool.
Loosen the knob located on the side of the light fixture housing.
Using the top handle, tilt to desired position then retighten knobs
(Fig. 3). There is a stop that restricts the downward and inward
movement of the fixture for safety reasons.
To prevent overheating and risk of burns or fire, do not aim the
fixture down at an angle of more than 10 degrees from horizontal.
• Plug light into a GFCI protected 120 Volt receptacle.
• To turn light ON or OFF, push red switch on the back of the fixture.
BONUS BULB INCLUDED
Note: Always handle halogen bulbs with gloves or with a clean soft cloth. Oil from
your skin can cause premature failure of the bulb.
This fixture includes a spare bulb, which insures that you can
always finish your job or project without interruption due to bulb
failure. The spare bulb and holder are located at the end of the
portable base. Simply pull the black knob on the end of the base
out, in order to access the spare bulb (Fig. 4).
REPLACING THE BULB
WARNING: Risk of burn. Disconnect power and allow fixture to cool
before changing bulb or handling fixture.
Note: Always handle halogen bulbs with gloves or with a clean soft cloth. Oil from
your skin can cause premature failure of the bulb.
Note: Replace with only a 120 or 130 Volt, 500 watt (or lower wattage) T2.5 R7s
base halogen bulb 4.6˝ long (Cooper Lighting, LLC model BP500Q).
1. Make sure fixture is turned OFF, unplugged and cool.
2. Turn screw on back of housing tab counterclockwise until
screw is loose on door frame.
3. The door frame and lens assembly will swing down allowing
access to the bulb.
4. Using gloves or soft cloth, press the old bulb to one side
of the spring loaded socket as indicated on the metal reflector.
Remove opposite end of bulb from the other side of the socket.
Remove the new bulb from its package making sure not to touch bulb with bare
hands. Reverse this procedure to install a new replacement bulb (Fig. 5).
5. Replace the door frame and lens assembly and secure it using a Phillips
screwdriver.
Fig. 3
Fig. 5
4°
Fig. 2
Fig. 4
All manuals and user guides at all-guides.com
Call for customer service and/or missing or damaged parts (800-334-6871)
5
TWO-YEAR LIMITED WARRANTY
Cooper Lighting, LLC (“the Company”) warrants this product (“the product”) against
defects in material or workmanship for a period of two years from date of original
purchase, and agrees to repair or, at the Companyʼs option, replace a defective
product without charge for either replacement parts or labor during such time.
This does not include labor to remove or install fixtures.
This warranty is extended only to the original purchaser of the product. A purchasers
receipt or other proof of date of original purchase acceptable to the Company is
required before warranty performance shall be rendered.
This warranty only covers product failure due to defects in materials or workmanship
which occurs in normal use. It does not cover the bulb or failure of the product
caused by accident, misuse, abuse, lack of reasonable care, alteration, or faulty
installation, subjecting the product to any but the specified electrical service or any
other failure not resulting from defects in materials or workmanship.
There are no express warranties except as described above.
THE COMPANY SHALL NOT BE LIABLE FOR INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT
OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL IMPLIED
WARRANTIES, IF ANY, INCLUDING IMPLIED WARRANTIES OF MERCHANTABIL-
ITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION
TO THE DURATION OF THIS EXPRESS WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, or limitations on how long an implied warranty lasts, so the above
exclusions or limitations may not apply to you.
No other warranty, written or verbal, is authorized by the Company. This warranty
gives you specific legal rights, and you may also have other rights which vary from
state to state.
To obtain warranty service, please write to: Cooper Lighting, LLC, 1121 Highway 74
South, Peachtree City, GA 30269. Enclose product model number and problems you
are experiencing, along with your address and telephone number. You will then be
contacted with a solution, or a Return Goods Authorization number and full instruc-
tions for returning the product. All returned products must be accompanied by a
Return Goods Authorization Number issued by the Company and must be returned
freight prepaid. Any product received without a Return Goods Authorization
Number from the Company will be refused.
Cooper Lighting, LLC is not responsible for merchandise damaged in transit.
Repaired or replaced products shall be subject to the terms of this warranty and are
inspected when packed. Evident or concealed damage that is made in transit should
be reported at once to the carrier making the delivery and a claim filed with them.
All manuals and user guides at all-guides.com
Loading...