Cooper Lighting NEO-RAY 75 User Manual

SERIES 75 INSTALLATION MANUAL

Figure 1

STEP 1.

Mount wall angle as shown in Figure 1.
Angles must be mounted level and true for fixtures to mount correctly

8'(TYPICAL)

WALL ANGLE PROVIDED
IN 8” SECTIONS
CUT LAST SECTION TO

FIT AVAILABLE SPACE

FINISHED CEILING

Figure 2

Use tie-wire (by others) to secure and level
fixture housings to structure.
Based on field dimension pre-cut 4 ft
aluminum housing to fit, using hand-saw.

STEP 1.

Attach housing to
wall angle. Support
housing to structure
with tie-wire.

STEP 2.

Install fixture from
left to right,
beginning with
larger housing to
smaller. Aluminum
housing should be
installed on right
end of the run.

STEP 3.

Join fixture using
joining plates.

JOINING PLATE

STEEL
HOUSING

ALIGNER CLIPS

CLEVIS BRACKET

(SEE DETAIL “B”)

1/4"

90° OUTSIDE
CORNER

ALUMINUM
HOUSING

NOTE “A”

·

Re-positioning clevis
brackets may be required
after cutting aluminum
housings

NOTE “B”

·

Last housing of run is
aluminum, to be field cut by

installing contractor.

For packing purposes,

·

aligning clips and spacer
blades are mounted at end
of housing as shown in

detail “A”.

When installing housings,

·

spacer blades will maintain
a proper opening.

Prior to housing installation,

·

reposition spacer blades
and aligning clips shown in

detail “B”.

Prior to installing shielding

·

element, remove and
discard spacer blades for all
shielding elements except

S72 bold bae.

STEP 4.

Align fixture using

SPACER BLADE

aligning clips.

Series 75R Installation Manual, Page 1 of 2

100 Andrews Rd., Hicksville, NY 11801 • Phone: [phone] • Fax: [phone] • http://www.neoray-lighting.com

A

B

SERIES 75 INSTALLATION MANUAL

Figure 3

LIGHTING STRIPS INSTALLATION (SEE DETAILS A & B)
STEP 1. Remove lighting strips covers

STEP 2. Install lighting strips into fixtures (attach to clevis bracket)

STEP 3. Attach first strip to outside power feed

STEP 4. Through wire all strips

STEP 5. Attach lighting strip covers to lighting strips

STEP 6. Install shielding

STEP 7. Install End Closure/End Plate

CHASE NIPPLE

FLEXIBLE CONDUIT
(NOT BY NEO-RAY)

DETAIL A

TOP VIEW

DETAIL B

CLEVIS BRACKET

END CLOSURE (FLAT )

END PLATE (FLANGED)

Typical Plan View
(Schematic)

TIE-WIRE
NOT BY NEO-RAY

6"

3 15/16"

END CLOSURE

STEEL HOUSING

ADJUSTABLE

LIGHT STRIP

ADJUSTABLE STRIP

STAGGERED STRIP

a) 3" STAGGER FOR T8 LAMP
b) 6" STAGGER FOR T5 OR T5HO LAMP

LAST HOUSING OF RUN IS FABRICATED OF ALUMINUM
TO BE FIELD CUT BY INSTALLING CONTRACTOR.

ALUMINUM HOUSING

90° OUTSIDE CORNER

(O.C.)

WORK FROM LEFT TO

RIGHT WHEN FACING WALL.

LIGHT STRIP

LIGHT STRIP COVER

90° INSIDE CORNER

(I.C.)

WALL RAIL

CEILING TILE

BY OTHERS

3/8"

3 3/16"

4 7/8"±1/8"

FINISH: BLACK

1/4"

5/8"±1/8"

135° OUTSIDE CORNER

Series 75R Installation Manual, Page 2 of 2

100 Andrews Rd., Hicksville, NY 11801 • Phone: [phone] • Fax: [phone] • http://www.neoray-lighting.com

(O.C.)

END PLATE

135° INSIDE CORNER

(I.C.)