Cooper Lighting MST20C18W User Manual

HOME

MST20C18B

(Bronze/Bronze/

Bronce)

TM

Instruction Manual/Manuel d’instructions/Instrucciones

Instruction Manual/Manuel d’instructions/Instrucciones

Questions?/Des questions?/¿Preguntas? 1-800-334-6871 [e-mail]

PACKAGING CONTENTS/ CONTENU DE L’EMBALLAGE/ CONTENIDO DEL PAQUETE

A. Motion detector
and light fixture

Détecteur de mouvements
et appareil d’éclairage

Detector de movimiento
y artefacto de luz

B. Mounting bracket
Support de montage
Soporte de montaje

C. Gasket
Joint
Junta

D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
(use the size that fits your junction box)

(2)vis nº6 de 32 x 3/4po et 2 vis nº8 de 32 x 3/4 po pou
boîtier de jonction (choisissez la dimension convenant
à votre boîtier de jonction)

(2) Tornillos #6-32 x 3/4 pulg. y (2) tornillos #8-32 x 3/4 pulg.
para montaje de la caja de conexiónes (utilice el tamaño que
mejor se adecue a su caja de conexiónes)

E. FLD-KIT-SFCGND

Adapter Plate Kit

Plaque adaptatrice trousse

Placa daptadora equipo

MST20C18W
(White/Blanc/

F. (2) #8-32 x 1-1/4 in. cover
mounting screws

(2) vis de protectionnº8
de 32 x 1-1/4po

(2) Tornillos #8-32 x 1-1/4 pulg.
de montaje de la cubierta

Blanco)

ENGLISH

ITEMS REQUIRED

(Purchase separately)

• Phillips screwdriver

• Outdoor weatherproof silicone caulking

IMPORTANT SAFETY INSTRUCTIONS

When using product, basic precautions should always be followed, including the following:

• Heed all warnings, including below warnings AND those included on product.

• Save these instructions and warnings.

• For outdoor use only.

• cULus LISTED for wet location.

• Disassembling your fixture will void the warranty.

• Your fixture is prewired and preassembled for easy installation.

WARNING

• Read and follow these instructions.

• Risk of fire/electric shock. If not qualified, consult an electrician.

• Disconnect power at fuse or circuit breaker before installing or servicing.

CAUTION

• Connect fixture to a 120-277 volt, 50/60 Hz power source. Any other connection voids
the warranty.

• Fixture should be installed by persons with experience in household wiring or by a
qualified electrician. The electrical system, and the method of electrically connecting
the fixture to it, must be in accordance with the National Electrical Code and local
building codes.

• Mount fixture to a grounded, recessed-mounted standard junction box marked for use
in wet locations.

• Suitable for wall mount or eave mount only. NOT suitable for ground mount installation.

• For proper operation and protection against damage, the motion sensor head
adjustment knobs must be facing the ground.

• Do not mount below 5 feet.

NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are

reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:

designed to provide

G. (2) Decorative screw
cover caps
(2)cache-vis décoratifs
(2) Cubiertas tapatornillos
decorativas

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

WARNING: FCC Regulations state that any unauthorized changes or modifications

to this equipment not expressly approved by the manufacturer could void the user’s
authorization to operate this equipment. FCC Radiation Exposure Statement: The
equipment complies with FCC Radiation exposure limits set forth for uncontrolled
enviroment. This equipment should be installed and operated with minimum distance
20cm between the radiator and your body.
NOTE: This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.

SAVE THESE INSTRUCTIONS.

FOR BEST RESULTS

• Install the motion sensor 8-12 feet
above the ground. (Motion sensor is less sensitive
above 12 feet.)

• Locate motion sensor so motion moves across
detection zone (Fig. 1).

• Locate sensor away from heat producing sources to
prevent false triggering. Also be very careful not to
include objects such as windows, white walls and
water in the detection zone.

• Locate sensor away from moving objects such as
trees, large shrubs and street traffic.

MOUNTING AND WIRING YOUR FIXTURE

WARNING: Risk of electric shock. Disconnect
power at fuse or circuit breaker before installing
or servicing.

NOTE: Fixture can be wall or eave mounted (Fig. 2).
NOTE: Coverplate mounts to recessed mounted

standard junction boxes (Fig. 3). Junction box must be at
least 1-1/2 inch in depth for proper installation for
recessed mount application. For surface mount junction
box installation, refer to installation instructions included
with the adaptar plate kit (E).

1. Line up the holes on the mounting bracket (B) with

the holes on your junction box. Using either (2) #6
screws or (2) #8 screws (D) (depending on size of

H. Support hook
Gancho de soporte
Crochet

1

2

3

1-1/2 in.

Round

Wall mount

Eave mount

1-1/2 in.

Octagonal

1

the holes in your junction box), attach the mounting
bracket (B) to your junction box (Fig. 4).

2. Thread fixture wires through coverplate

gasket (C) (Fig. 7).

3. Hang one end of the support hook onto the

mounting bracket and hang the light fixture on the
other end of the support hook (Fig. 5).

4. Connect house ground wire and fixture ground wire.
Connect fixture black wire to house black wire
and fixture white wire to house white wire by
firmly pushing into quick connect wiring connectors
(Fig. 7)

5. Remove support hook (H) and attach fixture (A) to
the mounting bracket (B) using (2) #8 x 1-1/4 in.
screws (F) pre-attached to the canopy. Be sure no
loose wires remain sticking out from underneath the
coverplate. Insert the decorative screw cover caps
(G) into the screw holes on the coverplate for a
finished appearance (Fig. 6).

6. Adjust light fixture to desired postion

7. Apply silicone caulk around the edges of the

coverplate to provide a watertight seal from
rain and moisture.

8. Turn on power at main fuse / breaker box.

6

A

F

G

F

G

7

TROUBLESHOOTING

Problem

Light does not
come ON with
motion at night.

Light comes ON
for no apparent
reason at night.

Light stays ON at
night and does
not turn OFF.

Light
continuously
blinks ON and
OFF at night.

Cause / Solution

No power to the fixture.

• Check if circuit breaker tripped.

• Confirm wall switch is ON.

• Check app settings
Surrounding external ambient light is too bright. (If so, the unit may

think it is daytime.)

• Re-aim the head.

• Relocate or reposition the unit away from the light.

TURN OFF POWER BEFORE CONTINUING

Wiring to the unit is loose.

• Check wiring; reconnect if necessary.

There is motion in the detection zone.

• Make sure the sensor is not picking up moving objects such as
trees, traffic, etc.

TEST FOR YOURSELF.

• Cover the sensor lens with cardboard to prevent sensor
from detecting motion. If the light stays off, something in the
detection zone is triggering the sensor.

* If the light stays on with the sensor lens covered, contact
customer service.

• Reposition the sensor.

There is motion in the detection zone.

• Make sure the sensor is not picking up moving objects such as
trees, traffic, etc.

• Reposition the sensor.
If there is no motion in the detection zone, unit is in an override
mode. Check app settings.

The light given from the unit’s own lamp is affecting the
motion sensor.

• Re-aim the lamp.

• Reposition motion sensor.

4

B

D

D

5

A

Junction box

E

C

Light is ON
during the day.

The motion sensor is in “TEST” mode.

• Inactivate “TEST” mode in the app.
The motion detector is shadowed.

• Reposition motion sensor.

5-YEAR LIMITED WARRANTY

THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Eaton warrants to customers that, for a period of five years from the date of purchase, Eaton
products will be free from defects in materials and workmanship. The obligation of Eaton
under this warranty is expressly limited to the provision of replacement products. This
warranty is extended only to the original purchaser of the product. A purchaser’s receipt or
other proof of date of original purchase acceptable to Eaton. This is required before warranty
performance shall be rendered. This warranty does not apply to Eaton products that have
been altered or repaired that have been subjected to neglect, abuse, misuse or accident
(including shipping damages). This warranty does not apply to products not manufactured by
Eaton which have been supplied, installed, and/or used in conjunction with Eaton products.
Damage to the product caused by replacement bulbs or corrosion or discoloration of brass
components are not covered by this warranty.
LIMITATION OF LIABILITY:
IN NO EVENT SHALL EATON BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT,
STRICT LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR SHALL
THE LIABILITY OF EATON FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR CONNECTED
WITH THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE, MAINTENANCE, REPAIR OR
MODIFICATION OF EATON PRODUCTS, OR SUPPLY OF ANY REPLACEMENT PARTS THEREFORE,

B

E

EXCEED THE PURCHASE PRICE OF EATON PRODUCTS GIVING RISE TO A CLAIM. NO LABOR
CHARGES WILL BE ACCEPTED TO REMOVE OR INSTALL FIXTURES.
To obtain warranty service, please contact Eaton at 1-800-334-6871, press option 2 for
Customer Service, or via e-mail [e-mail] and include the following
information:

• Name, address and telephone number

• Date and place of purchase

• Catalog and quantity purchase

• Detailed description of problem
All returned products must be accompanied by a Return Goods Authorization Number issued
by the Company and must be returned freight prepaid. Any product received without a Return
Goods Authorization Number from the Company will be refused. Eaton is not responsible for
merchandise damaged in transit. Repaired or replaced products shall be subject to the terms
of this warranty and are inspected when packed. Evident or concealed damage that is made
in transit should be reported at once to the carrier making the delivery and a claim filed
with them.

Reproductions of this document without prior written approval of Eaton are strictly prohibited.

For assistance, call 1-800-334-6871 or e-mail us at [e-mail]

Printed in China

FRANÇAIS

ARTICLES REQUIS:

(à acheter séparément)

• Tournevis cruciforme

• Calfeutrage en silicone étanche pour l’extérieur

IMPORTANTES INSTRUCTIONS DE SÉCURITÉ

Des précautions de base doivent être suivies lors de l’utilisation de ce produit, incluant :

• Le respect de tous les avertissements incluant les avertissements ci-dessous ET ceux
indiqués sur le produit.

• Conservez ces instructions et ces avertissements.

• Exclusivement réservé à un usage extérieur.

• Homologation cULus pour l’utilisation dans des endroits humides.

• Le démontage de l’appareil annule la garantie.

• L’appareil est câblé et assemblé à l’avance pour faciliter son installation.

AVERTISSEMENT

• Lisez et suivez ces instructions.

• Risque d’incendie ou de décharge électrique. Si vous n’êtes pas qualifié, consultez
un électricien.

• Coupez l’alimentation électrique depuis le fusible ou le disjoncteur avant l’installation
ou l’entretien.

MISE EN GARDE

• Raccordez le luminaire à une source d’alimentation de 120 V, 60 Hz. Tout autre
raccordement annule la garantie.

• L’appareil d’éclairage doit être installé par des personnes ayant l’expérience du
câblage domestique ou par un électricien qualifié. Le système électrique et la

méthode de raccordement électrique de l’appareil d’éclairage doivent être conformes
au Code national de l’électricité et aux codes locaux du bâtiment.

2