Cooper Lighting CMS185, MS185, MS185W, CMS185W User Manual
FRANÇAIS
ESPAÑOL
ENGLISH
MS185, CMS185
MS185W, CMS185W
Instruction Manual
Instrucciones
Directives
MS185,MS185W I.S. 325-1417 1/7/04 3:59 PM Page 1
Congratulations. You have purchased a Regent motion activated floodlight. This
security lighting system will provide years of convenience and protection for your
home and family.
How it works
Your Regent motion activated floodlight senses heat
images from objects such as people, large animals and
automobile engines. When motion is detected, the lights
will automatically turn on. Once motion has stopped, the
lights will turn off after a preselected time delay. Your
motion activated floodlight may also be used as a standard floodlight.
What you need
• Phillips screwdriver
• Outdoor weatherproof silicone caulking
• (2) 150 Watt (max) PAR 38 floodlight bulbs (A)
What’s included
• Motion detector and light fixture (B)
• Coverplate gasket (C)
• (2) Lampholder gaskets (D)
• (4) Mounting bracket screws (E)
• (3) Wire nuts (F)
• Color matched center hole plug (G)
• Center bolt (H)
• Mounting bracket (I)
What to know
• For outdoor use only.
• UL and cUL LISTED for wet locations.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation. Under Part 15 of the FCC Rules, any changes or
modifications to the motion detector described in this instruction sheet that are not
expressly approved by Cooper Lighting could void the user’s authority to operate
the equipment. NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
2
ENGLISH
MS185, CMS185 (Bronze)
MS185W, CMS185W (White)
70 foot
180 degrees
A
B
C
D
E
F
G
H
I
MS185,MS185W I.S. 325-1417 1/7/04 3:59 PM Page 2
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• Fixture must be connected to a 120 Volt, 60 Hz 2.5, 300 watt power source. Any
other connection voids warranty.
• This motion activated twin floodlight should be installed by persons with experience in household wiring or by a qualified electrician. The electrical system, and
the method of electrically connecting the fixture to it, must be in accordance with
the National Electrical Code and local building codes.
• For proper operation and protection against damage, the motion sensor head
adjustment knobs must be facing the ground.
• Disassembly of your fixture will void the warranty.
For best results
• Install your fixture 8-12 feet above ground (motion detector is
less sensitive above 12 feet).
• Locate fixture so motion moves across detection zone (J).
• Locate fixture away from heat producing sources to prevent
false triggering. Also be very careful not to include objects
such as windows, white walls and water in the detection zone whenever possible.
• Locate fixture away from moving objects such as trees and street traffic.
• Do not install more than one motion activated floodlight on one wall switch.
Mounting your fixture
Step 1: Turn off the power at the main
fuse/breaker box. Check to make
sure power has been disconnected
before continuing.
Step 2: Line up the holes on the mounting brack-
et with the holes on your junction box.
Using either (2) #6 screws or (2) #8
screws (depending on size of the holes in your
junction box), attach the mounting bracket to your
junction box (K).
Step 3: Thread fixture wires through coverplate gasket.
Step 4: Connect black wire to house black wire and con-
nect white wire to house white wire using wire
nuts provided.
Step 5: Attach fixture to the junction box with two screws
provided.
Step 6: Attach fixture to the mounting bracket using the center bolt provided.
Insert plastic color matched plug in center bolt hole for finished appearance.
Step 7: Apply silicone caulking around edges of coverplate
and in any open holes to provide a watertight
seal from rain and moisture.
Step 8: Insert gaskets into lampholder assembly, tight-
ly against lampholder and screw bulbs into
each lampholder. (Do not overtighten bulbs).
Step 9: Turn power on at main fuse/breaker box.
ENGLISH
3
J
Round Rectangular (horizontal) Octagonal
Your fixture mounts
to the following standard
junction boxes:
K
(eave mount)
(wall mount)
MS185,MS185W I.S. 325-1417 1/7/04 3:59 PM Page 3
How to operate your fixture
Step 1: Move slide switch on bottom of the sen-
sor to “TEST”. Set sensitivity knob to
medium (halfway) (L).
Step 2: Turn on the power to fixture. Allow fix-
ture to warm up approximately 40 seconds before testing. (Lights will come on
and stay on during warm-up
period.)
Step 3: Aim sensor head toward desired detection area, maintaining a 15° down
angle to allow moisture to drain. NOTE: Maintain air spacing between
lamps and sensor head, at least 1”. Make sure sensor head is positioned
with control switches facing towards the ground.
Step 4: Walk across the detection zone at the farthest distance you wish your
detector to detect motion.
Step 5: Adjust sensitivity until you get desired results. Lights will turn off 4 sec-
onds after all motion stops.
Step 6: Move slide switch to 4 MIN or 12 MIN (AUTO mode). At dusk, lights will
operate in the AUTO setting.
How to select your desired feature
4
ENGLISH
THIS IS THE
BOTTOM SIDE
OF THE MOTION
DETECTOR
L
TEST
4 MIN
12 MIN
SENSITIVITY
Auto Setting
(motion activated)
Lights should turn on with
motion only at night and
should turn off after
4 or 12 minutes.
4 MIN
or
12 MIN
Keep the power to
the fixture on.
Dusk to Dawn Setting
(activated only at night)
Lights should stay on from
dusk to dawn and then reset
to the auto setting next
dawn.
4 MIN
or
12 MIN
Turn power on and off twice
within 3 seconds.
Standard Floodlight
Setting
Lights should stay on
continuously both day and
night (must be reset
manually).
TEST Turn power on and off twice
within 3 seconds.
Test Setting
Lights should turn on with
motion both day and night.
Lights should turn off after
4 seconds.
TEST Keep the power to the
fixture on.
Return to Auto Setting
(motion activated)
From any of the above
settings.
4 MIN
or
12 MIN
Turn the power “OFF” for at
least 40 seconds., then
back “ON”.
Mode of
operation:
Set slide switch
on sensor to:
How to set
power switch:
MS185,MS185W I.S. 325-1417 1/7/04 3:59 PM Page 4
What to do if . . .
ENGLISH
5
Is there power to the fixture?
• Check to see that the circuit breaker has not
been tripped.
• Be sure the wall switch is in the “ON” position.
• Be sure that the bulbs are not burned out or
broken.
Is the surrounding external ambient light too bright?
(If so the unit may think it’s daytime.)
• Re-aim the head.
• Relocate or reposition the unit away from the
light.
TURN OFF POWER BEFORE CONTINUING.
Is the wiring to the fixture loose?
• Check wiring, and reconnect if necessary using
wire nuts provided.
OUTDOOR LIGHTS DO
NOT COME ON WITH
MOTION AT NIGHT
OUTDOOR LIGHTS
COME ON FOR NO
APPARENT REASON
AT NIGHT
LIGHTS STAY ON AT
NIGHT AND DO NOT
TURN OFF
LIGHTS CONTINUOUSLY
BLINK ON AND OFF AT
NIGHT
LIGHTS ARE ON
DURING THE DAY
Is there motion in the detection zone?
• Make sure the sensor is not picking up moving
objects such as trees, traffic, etc.
TEST FOR YOURSELF
• Cover the sensor lens with cardboard to prevent sensor from detecting motion. If the lights
stay off, something in the detection zone is
triggering the sensor.
• If this is the case, reduce the sensitivity.
• Reposition motion sensor.
*If the lights stay on with sensor lens covered,
contact customer service.
Is there motion in the detection zone?
• Make sure the sensor is not picking up moving
objects such as trees, traffic, etc.
• If this is the case, reduce the sensitivity.
• Reposition motion sensor.
If there is no motion, then the unit may be in the
override mode.
• Turn the light switch to the “OFF” position for
40 seconds, and then back to the “ON” position. This will send the unit back into the
AUTO mode.
*If the lights continue to stay on, contact
customer service.
The light given off from the unit’s own lamps are
affecting the motion sensor.
• Re-aim lamps.
• Reposition motion sensor.
Is the switch on the bottom of the motion sensor in
the test mode?
• Move the switch to the 4 MIN or 12 MIN
position.
Is the motion detector shadowed?
• Reposition motion sensor.
MS185,MS185W I.S. 325-1417 1/7/04 3:59 PM Page 5
Two year limited warranty
Cooper Lighting (“the Company”) warrants this product (“the product”) against
defects in material or workmanship for a period of two years from date of original purchase, and agrees to repair or, at the Company’s option, replace a
defective product without charge for either replacement parts or labor during
such time. This does not include labor to remove or install fixtures.
This warranty is extended only to the original purchaser of the product. A purchasers receipt or other proof of date of original purchase acceptable to the
Company is required before warranty performance shall be rendered.
This warranty only covers product failure due to defects in materials or workmanship which occurs in normal use. It does not cover the bulb or failure of
the product caused by accident, misuse, abuse, lack of reasonable care, alteration, or faulty installation, subjecting the product to any but the specified electrical service or any other failure not resulting from defects in materials or workmanship. Damage to the product caused by separately purchased, nonCompany brand replacement bulbs and corrosion or discoloration of brass
components are not covered by this warranty.
There are no express warranties except as described above.
THE COMPANY SHALL NOT BE LIABLE FOR INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL
IMPLIED WARRANTIES, IF ANY, INCLUDING IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED IN DURATION TO THE DURATION OF THIS EXPRESS WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above
exclusions or limitations may not apply to you.
No other warranty, written or verbal, is authorized by the Company. This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
To obtain warranty service, please write to Cooper Lighting, 1121 Highway 74
South, Peachtree City, GA 30269. Enclose product model number and problems you are experiencing, along with your address and telephone number.
You will then be contacted with a solution, or a Return Goods Authorization
number and full instructions for returning the product. All returned products
must be accompanied by a Return Goods Authorization Number issued by the
Company and must be returned freight prepaid. Any product received without
6
ENGLISH
Is the surrounding external ambient light too bright?
(If so the unit may think it’s daytime.)
• Re-aim the head.
• Relocate or reposition the unit away from the
light.
Are you allowing adequate time to enter the Dusk
to Dawn mode?
• Turn power on and off twice within 3 seconds.
Is there more than one fixture on an indoor wall
switch?
• If so, put them on separate switches.
CANNOT ACTIVATE
DUSK TO DAWN MODE
AT NIGHT (OVERRIDE)
MS185,MS185W I.S. 325-1417 1/7/04 3:59 PM Page 6
Loading...