Cooper Lighting MCL5 User Manual

ENGLISH

ESPAÑOL

FRANÇAIS

MCL35

Instruction Manual
Instucciones
Directives

MCL35 325-1577.qxd 8/23/06 3:28 PM Page 1

MCL35

ENGLISH

2

Call for customer service and/or missing or damaged parts (800-334-6871)

Congratulations! You have purchased a Cooper Lighting halogen clamp
light. This light is perfect for providing light in small, difficult to reach areas.
The convenient clamp and hook provide a great deal of flexibility in most
applications.

What you need

• 3 Wire grounded extension cord

What’s Included

• Light fixture (A)

• 35 watt premium halogen bulb (B)

• Wire guard (C)

• Vinyl coated hook (D)

• Clamp (E)

What’s to know

INSTRUCTIONS PERTAINING TO RISK OF
FIRE, ELECTRIC SHOCK, EXPOSURE TO
EXCESSIVE UV RADIATION OR INJURY TO PERSONS.

IMPORTANT SAFETY INSTRUCTIONS.
READ ALL INSTRUCTIONS.
NOTE: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, EXPOSURE TO EXCESSIVE UV RADIATION
OR INJURY TO PERSONS:

WARNING: Risk of Burn. Disconnect power and allow fixture to
cool before changing bulb or handling fixture.

• Lighted lamp is HOT!

• Do not remain in light if skin feels warm.

• For indoor and outdoor use.

• cULus Listed for wet location use.

• Fixture must be connected to a 120 Volt, 60 Hz power source. Any other
connection voids warranty.

• Keep away from flammable objects.

• The bulb and fixture get extremely hot during use. Always unplug the light
and let it cool 5 minutes before attempting to touch the fixture.

• Do not touch hot lens, guard, or enclosure.

• Bulb gets HOT quickly! Only contact switch/plug when turning on.

• The electrical system, and the method of electrically connecting the fixture
to it, must be in accordance with the National Electrical Code and local
building codes.

A

B

C

D

E

MCL35 325-1577.qxd 8/23/06 3:28 PM Page 2

ENGLISH

3

Call for customer service and/or missing or damaged parts (800-334-6871)

• Do not operate the unit with a missing or damaged wire safety guard, or safety
glass lens (lamp containment / UV filter).

• Do not direct the light at persons or look directly at lighted fixture.

• Use only with a 35 watt or smaller bulb. Installing a bulb of a higher
wattage could create a fire hazard. Use of a higher wattage bulb will
void the warranty.

• Never touch the bulb with your bare hands. Oil from your skin can cause pre
mature failure. Always handle the bulb with gloves or a soft cloth.withple Ima

• If lens is replaced, use only a diffused tempered safety glass of equal thickness.

• Disassembly of your fixture will void the warranty.

NOTE: When using outdoor use portable lamps, basic safety
precautions should always be followed to reduce the risk of fire,
electric shock and personal injury, including the following...

• Use only with three wire extension cords that have three-prong grounding
plugs and that are suitable for outdoor use, such as cords marked SW, SW-A,
SOW, SOW-A, STW, STW-A, STOW, STOW-A, SJW, SJW-A, SJOW,
SJOW-A, SJTW-A, SJTOW, SJTOW-A and grounding receptacles that accept
a three-prong plug. When the fixture is used in wet locations, Ground Fault
Circuit Interruption (GFCI) protection must be provided on the circuit(s) or out
let(s) to be used. Receptacles are available having built-in GFCI protection
and are able to be used for this measure of safety.

NOTE: Deviation from the assembly instructions may result in a
risk of fire or electric shock.

SAVE THESE INSTRUCTIONS.

Installing the bulb

Step 1: Remove the lens cover by twisting it one-half turn counter-clockwise.
Step 2: Using gloves or a soft cloth, gently plug bulb into housing.

NOTE: Align two pins located at the end of the bulb with two small
holes in the center of housing, and press until firmly seated.

Step 3: Replace the lens (making sure the gasket is in place) by aligning the

notches on the housing with the cover and pressing until seated. Twist
one-half turn clockwise until tight.

Assembling your fixture

Squeeze sides of wire guard while positioning it over the glass lens and release
sides so that the ends of the wire guard slip into open slots in lens cover.

How to use

Attach light near work surface, using spring clamp on bottom of light or hang
the light with vinyl coated hook attached to the side of the clamp. Plug the light
into a 3 wire grounded extension cord. Plug the extension cord into any
standard grounded 120 Volt receptacle. Press switch to turn on light. Press
opposite side to turn the light off.

NOTE: The power cord length of this fixture was selected to
reduce safety hazards that may occur with a longer power cord.

MCL35 325-1577.qxd 8/23/06 3:28 PM Page 3

ENGLISH

4

WARNING: Do not touch fixture housing during use as the fixture
housing gets extemely hot. Unplug fixture and allow to cool before
replacing bulb.

Aiming the light

Loosen the knob on the side of the light housing. Using the rubber grip that
wraps around the housing, tilt to desired position, then retighten knob. To turn
the light (left or right), loosen the knob located under the clamp. Turn the light to
desired position, then retighten knob.

WARNING: Deviation from the assembly instructions may result
in a risk of fire or electric shock.

SAVE THESE INSTRUCTIONS.

Two Year Limited Warranty

Cooper Lighting (“the Company”) warrants this product (“the product”) against
defects in material or workmanship for a period of two years from date of
original purchase, and agrees to repair or, at the Company’s option, replace a
defective product without charge for either replacement parts or labor during
such time. This does not include labor to remove or install fixtures.

This warranty is extended only to the original purchaser of the product.
A purchasers receipt or other proof of date of original purchase acceptable to
the Company is required before warranty performance shall be rendered.
This warranty only covers product failure due to defects in materials or
workmanship which occurs in normal use. It does not cover the bulb or failure
of the product caused by accident, misuse, abuse, lack of reasonable care,
alteration, or faulty installation, subjecting the product to any but the specified
electrical service or any other failure not resulting from defects in materials or
workmanship. Damage to the product caused by separately purchased,
non-Company brand replacement bulbs and corrosion or discoloration of
brass components are not covered by this warranty.

There are no express warranties except as described above.
THE COMPANY SHALL NOT BE LIABLE FOR INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE
PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL
IMPLIED WARRANTIES, IF ANY, INCLUDING IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED IN DURATION TO THE DURATION OF THIS EXPRESS WARRANTY.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty
lasts, so the above exclusions or limitations may not apply to you.

No other warranty, written or verbal, is authorized by the Company.
This waranty gives you specific legal rights, and you may also have other

rights which vary from state to state. To obtain warranty service, please write to
Cooper Lighting 1121 Highway 74 South, Peachtree City, GA 30269. Enclose
product model number and problems you are experiencing, along with your
address and telephone number. You will then be contacted with a solution, or a
Return Goods Authorization number and full instructions for returning the

Call for customer service and/or missing or damaged parts (800-334-6871)

MCL35 325-1577.qxd 8/23/06 3:28 PM Page 4