Cooper Lighting McGraw-Edison IMI-6950 User Manual

FAILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR
DEATH

TASK LIGHT FIELD KIT INSTALLATION: (Figure 1)

1. Note: Remove tamper proof screws first if luminaire includes (TR)

tamper-resistant option. (Figure 1).

2. To release clasp lock on “quick mount” bracket, push handle inward and
pull luminaire forward. (Figure 2). CAUTION: Do not let luminaire fall.
Support luminaire while lowering off of j-box to resting/hanging position.

3. Remove luminaire hanging hook from quick mount plate (Figure 3 & 4).
CAUTION: Support luminaire while removing.
CAUTION: DO NOT place luminaire directly with lens facing down; it may

scratch or cause the lens to break. Place fixture with lens facing upright on
stable work surface. SUGGESTION: Remove the lens completely in order to
perform remaining of Task Light accessory installation.
Unlatch both latches. CAUTION: To avoid lens breakage, remove lens
retainer if necessary (Figure 5). Remove the complete lens assembly and
set aside to prevent damage. Take off upper reflector by loosening
thumbscrews (See figure 6).

4. Reference dimensions as shown and mark housing if necessary
(Figure 7 & 8).

5. Line up an adapter block and secure tightly if possible to aid in drilling
(Figure 7 & 8).
CAUTION: DO NOT drill or damage other components inside luminaire. To
avoid this from happening, remove them if necessary.

6. Drill center hole as specified and de-burr if necessary to remove sharp
edges (Figure 7 & 8).

7. Drill and tap the two outside holes as specified (Figure 7 & 8).

8. Install gasket and adapter block (with provided fasteners) (Figure 9).

9. Apply sealing compound on the threads of handle (provided by others).

10. Pull wires out of head through access in block. Screw the handle into

adapter block. On inside of fixture, make connections and restrain with
wire tie.

11. Aim the handle to a preferred position and lock it in position.

12. Aim task light head to a preferred position and tighten #10-24 Allen head

screw (with provided Allen wrench).

13. To install lamp, remove task light cover by twisting counter-clockwise and

pulling out (Figure 9). CAUTION: Verify that lamp source and wattage
correspond with the luminaire label.

14. Re-install task light cover by pushing in and rotating clockwise (Figure 9).

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency during installation,
operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative.

NOTE: Specifications and dimensions subject to change without notice.

EPL Envoy

Task Light Field Installation Kit

Sheet 1 of 3

4/7/08 IMI-695D

INSTALLATION INSTRUCTIONS

IMPORTANT : READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE

GENERAL: Upon receipt of luminaire thoroughly inspect for any freight
damage, which should be brought to the attention of the delivery
carrier. Compare the catalog description listed on the packing slip
with the luminaire label on the housing to assure you have received the
correct merchandise.
SAFETY: This luminaire must be wired in accordance with the national
electrical code and applicable codes and ordinance. Proper grounding
is required to insure personal safety. Carefully observe grounding
procedure. All work should be done by a qualified electrician.

WARNING: Make certain power is OFF before starting installation or
attempting any maintenance.
WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit
breaker before installing or servicing.
WARNING: Risk of Burn. Disconnect power and allow luminaire to cool
before changing lamp or handling luminaire.
WARNING: RISK OF FIRE! DO NOT mount on or near combustible
materials.

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX [phone] ADH080775

Figure 3

Figure 2

TO REMOVE

Figure 1

TAMPER-PROOF
SCREW FOR HANDLE

TAMPER-PROOF
SCREW FOR LATCH

HANDLE

PUSH

PULL

LATCH

QUICK MOUNT
PLATE

HANGING
HOOK

LUMINAIRE

LUMINAIRE RE-INSTALLATION:

1. Note: Install lens to housing if removed during drilling. Reverse Step 3.

2. Secure hanging hook into the rear hooks of quick mount plate

(Figure 3 & 4).

3. Make wiring connection while luminaire is being suspended from hanging
hook.

4. Push excess wires and connectors up into the junction box.

5. Lift up luminaire onto the (4) four hooks of quick mount plate while guiding

the wires through center access hole (Figure 3).

6. Push luminaire forward for engagement. When it reaches the full-engaged
position, a “CLICK” can be heard.

CAUTION: If full engagement is not reached, it is not yet rigidly installed.

EPL Envoy

Task Light Field Installation Kit

Sheet 2 of 3

4/7/08 IMI-695D

INSTALLATION INSTRUCTIONS

IMPORTANT : READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX [phone] ADH080775

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency during installation,
operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative.

NOTE: Specifications and dimensions subject to change without notice.

Figure 6

Figure 4

FRONT HOOKS

LUMINAIRE
HANGING HOOK

REAR HOOKS

QUICK MOUNT
PLATE

Figure 5

LATCH

#8-32
SCREW

RETAINER

CENTER ACCESS HOLE

THUMB
SCREW

UPPER
REFLECTOR