Cooper Lighting M2N-E SLI User Manual
Warning
that all sources of power are turned off. All
work must meet local/national codes and be
performed by a certified electrician.
mount fixtures vertically.
: Before starting any work ensure
Do not
Exploded View and Part Call-Out
Installation Instructions
Sheet 1 of 3
Roundel, XL
IN/OUTDOOR
P1R
(Pendant, 1-way, Remote)
Visor and Non-Visor
J-box
(by others)
Electrical cover
plate
1-way Yoke
Aiming screw
spacer
Yoke arms
1/4-20 x1"
Aiming screw
(x2)
All extra large fixtures require additional bracing/structure around J-box to support fixture.
Securing Pendant to Structure in Ceiling
1.
J-box
(by others)
Appropriate fasteners
(by others)
Canopy
End cap
Mounting
plate
Attention:
2.
Mounting plate
Pendant length
dependant on order
1/4-20 x 4"
Hex bolt
(x2)
Fixture door
3/8-16x1"
Hex end bolt
(x2)
Securing Yoke to Pendant
1/4-20 x 4"
Hex bolt
(x2)
1-way
yoke
#10-32 x 1/2"
Pan head screws
(x2)
Canopy
1.
Loosen both #10-32 x1/2" Pan head screws and allow canopy
to slide down pendant.
2.
Feed power wire from j-box into pendant, ensure wire reaches
electrical cover plate on base of pendant.
3.
Using appropriate fasteners(by others), secure mounting plate
to structure/bracing around J-box.
ADY080866 REV A(ECN080377)
1/4-20 x1"
Button socket screws
(x4)
Yoke arms
1.
Using all four 1/4-20 x1" screws, secure yoke arms to 1-way
yoke.
2.
After securing arms, slide 1-way yoke assembly onto pendant
and secure using both 1/4-20 x 4" hex bolts.
Warning
that all sources of power are turned off. All
work must meet local/national codes and be
performed by a certified electrician.
mount fixtures vertically.
: Before starting any work ensure
Do not
Installation Instructions
Sheet 1 of 3
Roundel, XL
IN/OUTDOOR
P1R
(Pendant, 1-way, Remote)
Visor and Non-Visor
3.
Aiming screw
spacer
(x2)
1/4-20 x 1"
Aiming screw
(x2)
1.
While firmly supporting fixture head, use 3/8-16 x1" hex end bolt to secure fixture head to yoke arms.
2.
Slide one aiming screw spacer between fixture head and yoke arm on each side and secure fixture heads angle using 1/4-20 x1"
aiming screws.
3.
Remove electrical cover plate from pendant tube.
4.
Insert fixture head wire into wire connection at base of pendant tube and run up to electrical cover plate.
5.
Attach appropriate wires ensuring all connections are properly matched and replace electrical cover plate.
4.
Securing and Wiring the Fixture Head to Pendant
Electrical cover
plate
End cap
Aiming and Sealing Fixture
Wire connector
3/8-16 x 1"
Hex end bolt
(x2)
Electrical cover plate
gasket
Wire connectors
(x2)
1/4-20 x1"
Aiming screw
(x2)
End cap
(x2)
1.
To aim fixture, unscrew end caps from fixture. Loosen both 1/4-20 x1" aiming screws on both sides of fixture. When
yoke indicator and fixture head indicator are lines up the slope of the fixture head is 40-degrees. Each subsequent notch
is an additional 10-degrees. When fixture is rotated to desired angle, secure with aiming screws.
2.
Secure door using proper torque specifications and sequence as described in supplementary sheet.
3.
Thoroughly check seal on all gaskets and wire connectors to ensure seals are smooth and compressed.
Captive door
screws
(x10)
40
Side View
ADY080866 REV A(ECN080377)
Loading...