Cooper Lighting IMI-694 User Manual

FAILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR
DEATH

NOTE : Use minimum 90°C supply wire rating for connections in J-box.

Fixture Orientation Guideline:

Proper orientation of luminaire may vary based upon design requirements
specified per given application. Labels are supplied on top of fixture and
mounting plate for reference to proper fixture alignment. Align quick mount
plate in correct direction by referencing number of fixtures required (double or
single row luminaire installation) to direction of arrows. Direction of arrow(s)
should be in line with direction of traffic.

LUMINAIRE INSTALLATION:

1. Install quick mount plate on a 4” junction box as shown in (Figure 1).

Note the required position of plate to ensure correct light beam
orientation from fixture. See guidelines above or labels on top of fixture
housing and mounting plate if applicable.

2. Secure hanging hook into the rear hooks of quick mount plate
(Figure 2 & 3).

3. Make wiring connection while luminaire is being suspended from hanging
hook.

4. Push excess wires and connectors up into the junction box through center
access hole.

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency during installation,
operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative.

NOTE: Specifications and dimensions subject to change without notice.

EPL Envoy

Parking Luminaire

Sheet 1 of 5

8/20/08 IMI-694

INSTALLATION INSTRUCTIONS

IMPORTANT : READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE

GENERAL: Upon receipt of luminaire thoroughly inspect for any freight
damage, which should be brought to the attention of the delivery
carrier. Compare the catalog description listed on the packing slip
with the luminaire label on the housing to assure you have received the
correct merchandise.
SAFETY: This luminaire must be wired in accordance with the national
electrical code and applicable codes and ordinances. Proper grounding
is required to insure personal safety. Carefully observe grounding
procedure. All work should be done by a qualified electrician.

WARNING: Make certain power is OFF before starting installation or
attempting any maintenance.
WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit
breaker before installing or servicing.
WARNING: Risk of Burn. Disconnect power and allow luminaire to cool
before changing lamp or handling luminaire.

WARNING: This luminaire is for use with downlight applications only.
WARNING: RISK OF FIRE! DO NOT mount on or near combustible

materials.

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX [phone] ADH080771

Figure 3

Figure 1

Figure 2

CENTER ACCESS
HOLE

#8-32 SCREW

QUICK MOUNT
PLATE

J-BOX

J-BOX

HANGING
HOOK

LUMINAIRE

LIFT UP

THEN PUSH
LUMINAIRE
BACK

FRONT HOOKS

LUMINAIRE
HANGING HOOK

REAR HOOKS

QUICK MOUNT
PLATE

J-BOX

5. Lift up luminaire onto the (4) four hooks of quick mount plate while guiding
the wires through center access hole (Figure 3).

6. Push luminaire forward for engagement (Figure 3). When it reaches the
full-engaged position, a “CLICK” can be heard.

CAUTION: If full engagement is not reached, it is not yet rigidly installed.

REMOVAL OF LUMINAIRE:
WARNING: Make sure the power to the unit is OFF and allow it to cool.

1. Note: Remove tamper proof screws first if luminaire includes (TR)

tamper-resistant option (Figure 4).

2. To release clasp lock on “quick mount” bracket, push handle inward and
pull luminaire forward (Figure 5).
CAUTION: Do not let luminaire fall. Support luminaire while lowering off of
j-box to resting, hanging position.

3. Remove hanging hook from quick mount plate (Figure 2 & 3).
CAUTION: Support luminaire while removing.

4. For re-installation of luminaire, refer to steps 1 through 6 on Luminaire

Installation.

EPL Envoy

Parking Luminaire

Sheet 2 of 5

8/20/08 IMI-694

INSTALLATION INSTRUCTIONS

IMPORTANT : READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX [phone] ADH080771

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency during installation,
operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative.

NOTE: Specifications and dimensions subject to change without notice.

Figure 5

TO REMOVE

Figure 4

TAMPER-PROOF
SCREW FOR HANDLE

TAMPER-PROOF
SCREW FOR LATCH

HANDLE

PUSH

PULL

LAMP INSTALLATION: :

1. To install the lamp, unlatch both latches (Figure 6). Note: Remove tamper

proof screws first if luminaire includes (TR) tamper-resistant option (Figure

4).

2. Allow lens to swing open (Figure 7). Lens will remain captive.
CAUTION: Support lens while it swings open.

3. Install lamp securely into socket. CAUTION: Verify that lamp source and

wattage correspond with the luminaire label.

4. To close the luminaire, rotate lens back up to position. Lift up the lens and
align with (4) ribs of top lens on both sides(Figure 8).
CAUTION: Latching luminaire closed prior to having proper alignment will
result in lens breakage.

5. Push one side of the latch up to grasp edge of lens and then push inward to
complete latching (Figure 9 & 10). Repeat for the other latch.

EPL Envoy

Parking Luminaire

Sheet 3 of 5

8/20/08 IMI-694

INSTALLATION INSTRUCTIONS

IMPORTANT : READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX [phone] ADH080771

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency during installation,
operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative.

NOTE: Specifications and dimensions subject to change without notice.

Figure 6

Figure 7

Figure 8

Figure 9

Figure 10

PULL TO
UNLATCH

PULL TO
UNLATCH

LAMP

SUPPORT LENS
WHILE IT SWINGS
OPEN

ALIGN THESE RIBS AS
SHOWN BEFORE LATCHING
(OTHER SIDE NOT SHOWN)

LATCH

LENS

LATCH UP TO
GRASP EDGE
OF LENS BEFORE
LATCHING

PUSH TO
LATCH

PUSH TO
LATCH

TRUNNION MOUNT INSTALLATION: (Figure 11)
Note: Use minimum 90°C supply wire when installed per below procedure

and connections are made inside of condulet body.

Note: For 8-3/8” to 13-1/4” vertical adjustment (Up or Down only).

1. Install top trunnion on the ceiling using masonry anchors (provided by

others).

2. Apply sealing compound (by others) on one end of ½” nipple.

3. Screw nipple into the housing.

4. Install bottom trunnion L-brackets on the top plate (with provided #10-24

pan head screws, lock washers and nuts—Torque between 24-27 in-lb).

5. Install top plate on the housing (with provided #10-24 flat head screws—
Torque between 24-27 in-lb).

6. Pull wires from back of luminaire through nipple to make for easy routing
into condulet body.

7. Apply sealing compound to top of nipple. Screw condulet body onto nipple.

8. Install bottom trunnion L-brackets to the top trunnion (with provided 3/8"

bolts, lock washers and nuts—Torque between 17-20 ft-lb).

9. Route conduit and power supply wires to condulet body.

10. Make connections. Push excess wires and connectors back into the

condulet body.

11. Install gasket and cover.

TASK LIGHT INSTALLATION: (Figure 12)
WARNING: RISK OF FIRE! DO NOT mount on or near combustible materials.

1. Apply sealing compound on the threads of handle (provided by others).

2. Screws handle into adapter.

3. Aim handle to a preferred position and lock it in position.

4. Aim task light head to a preferred position and tighten #10-24 Allen head

screw (with provided Allen wrench).

5. Pull wires through access and restrain with wire tie.

Note: Depending on which task light option is being ordered, additional

wiring/routing will be necessary. Reference wiring diagrams shipped with
task light.

EPL Envoy

Parking Luminaire

Sheet 4 of 5

8/20/08 IMI-694

INSTALLATION INSTRUCTIONS

IMPORTANT : READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX [phone] ADH080771

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency during installation,
operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative.

NOTE: Specifications and dimensions subject to change without notice.

Figure 12

Figure 11

#10-24
ALLEN HEAD

LOCK NUT

ADAPTER

HANDLE

(APPLY SEALING

COMPOUND BY OTHERS)

TASK LIGHT
HEAD

FOR VERTICAL ADJUSTMENT (UP OR DOWN ONLY)

8-3/8 TO 13-1/4” FROM TOP OF LUMINAIRE

CONDULET
BODY

TOP
TRUNNION

TOP PLATE

NIPPLE
APPLY SEALING
COMPOUND
(BY OTHERS)

#10-24
SCREW

HOUSING

BOTTOM
TRUNNION

#10-24 FLAT
CS SCREW

GASKET

COVER

3/8” BOLT

THRU-BRANCH WIRING INSTALLATION: (Figure 13 & 14)
NOTE : Use 90°C wire rating for luminaire with thru-branch option for

fixtures 100w or below at 25°C ambient temperature applications.

: Use 105°C wire rating for luminaire with thru-branch option for

150w to 175w at 25°C ambient temperature applications

: Use 125°C wire rating for luminaire with thru-branch option for

200w at 25°C ambient temperature applications.

: Use 150°C wire rating for luminaire with thru-branch option for all

fixtures at 40°C ambient temperature applications.

WARNING: RISK OF FIRE! DO NOT mount on or near combustible materials.
Note: Requires luminaire option (CT) =Conduit Tap-(2) ¾” NPSM taps and

plugs.

1. Remove lens and housing cover from luminaire.

2. Remove conduit plugs.

3. Affix luminaire to the ceiling with anchors through cast in knock outs

(anchors provided by others). Use RTV or other liquid sealant around
perimeter of KO’s.

4. Apply sealing compound to end of pipe if applicable. Install conduit pipe.

5. Route wires inside the housing as shown and use wire ties and screws to

restrain in position.
CAUTION: Use wire ties/self-tapping screws to restrain wires from
contacting ballast (provided by others).

EPL Envoy

Parking Luminaire

Sheet 5 of 5

8/20/08 IMI-694

INSTALLATION INSTRUCTIONS

IMPORTANT : READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX [phone] ADH080771

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency during installation,
operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative.

NOTE: Specifications and dimensions subject to change without notice.

Figure 13

Figure 14

#10-24 X 5/8 TAPTITE
SCREW (BY OTHERS)

WIRE TIE
(BY OTHERS)

KNOCK-OUT
FEATURE

THRU-BRANCH
FEATURE

CONDUIT
PIPE

KNOCK-OUT
FEATURE

KNOCK-OUT
FEATURE

WIRE TIE
(BY OTHERS)

KNOCK-OUT
FEATURE

KNOCK-OUT
FEATURE

KNOCK-OUT
FEATURE

KNOCK-OUT
FEATURE

KNOCK-OUT
FEATURE

CONDUIT
PIPE

THRU-BRANCH
FEATURE

WIRE TIE
(BY OTHERS)

#10-24 X 5/8 TAPTITE
SCREW (BY OTHERS)

WIRE TIE
(BY OTHERS)