Cooper Lighting IMI-685 User Manual

Tools Required Socket, 5/16" Socket, 3/4" Deep Well Socket, Electrical

wiring tools.

NOTE: these luminaires are designed for outdoor lighting
services, and should not be used in area of limited ventilation
or in high ambient temperature enclosures. Construction is
suitable for down lighting only. Best results will be obtained
if installed and maintained according to the following
recommendations.

1. Open housing door by squeezing thumb latch towards front of
housing. To relieve latch pressure, compress gasket by pushing
door into housing. Once the latch is disengaged, gently swing the door
open. FIG. 1

2. Remove the door by opening it to 45° angle “half open/half closed” then
lift it off the hook shaped hinges. FIG. 2

3. Remove the electrical compartment cover.

Hard Mount Version

• Hard mount electrical covers requires captive screws “1” & “2” to be
loosened. Grab handle and remove cover. FIG. 3a

Power Tray Version

• Power tray version requires captive screw “1” to be loosened. FIG. 3a

• Grab handle and open power tray. FIG. 3b

• To remove power tray from housing, unhook pin through gap in
power tray. Slide off of back pin and unplug the electrical
connection. FIG. 3c

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency
during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest
representative.

Tribute

Sheet 1 of 4

1/7/08 IMI-685

INSTALLATION INSTRUCTIONS

IMPORTANT : READ CAREFULLY BEFORE INSTALLING FIXTURE.

WARNING: Risk of Fire/Electric Shock. If not qualified, consult an electrician.
WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing.
WARNING: Risk of Burn. Disconnect power and allow fixture to cool before changing bulb or handling fixture.
WARNING: Risk of Personal Injury. Fixture may become damaged and/or unstable if not installed properly.

Tighten all fixture components to their recommended torque values. Ensure door is properly latched.

WARNING: Risk of Fire/Electrical Shock. Upside down installation can result in overheating or accumulation of water in fixture. Install right side up.

NOTE: Specifications and dimensions subject to change without notice

Visit our web site at www.cooperlighting.com

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX [phone] ADH070937

FIG. 1

FIG. 2

Open

FIG. 3a

Screw “1”

Handle

FIG. 3b

Power

Tra y

FIG. 3c

Latch

Lift

Screw “2”

Mounting the fixture

4a. Arm Mount (FIG. 4a)

• Arm Mounting (Square Pole) Lay the fixture on its’ top
with door removed. Remove pole cap allowing nut plate
to be inserted into pole and align with bolt holes. Install
threaded bolts into nut plate. Align arm (end with drain
holes towards pole) and place over threaded bolts.
Align holes in fixture with bolts. Route fixture supply leads
through arm and into pole. Inside of fixture place lock
washer and nuts onto threaded bolts, secure. Housing
and arm must be square with pole. Tighten bolts to 30 ft
lbs. Bolts must not be extended into fixture more than 1".
Finish securing electrical connections inside of pole.

• Arm Mounting (Round Pole) Installation is the same as
square pole except a round pole adapter is used against
the round pole.

4b. Internal Mast Arm Mount (FIG. 4b)

• Loosen the four tenon clamp bolts for insertion of the
mounting tenon. Note: for the 2" pipe size tenon,
remove the tear away portion of the tenon entrance
gasket. To remove, grasp the aluminum gasket with
pliers and twist off the pre-cut portion of the gasket.

• Pull service lead wires through the mounting tenon until
about 6" extends beyond the tenon end.

• Slide the luminaire onto the tenon while guiding the
service lead wires. Make sure end of tenon is against
stop in housing.

• Tighten 4 tenon clamp bolts. Note: fixture can be
leveled by tightening front bolts differently than rear
bolts. When fixture is level, torque all 4 clamp bolts to
100 inch-pounds. Tighten bolts in alternating pattern.

• Connect service lead wires to fixture leads and anchor
leads in place so they are not in contact with the reflector
surface or ballast surface.

• Replace electrical compartment cover removed in
step 3.

These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency
during installation, operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest
representative.

Tribute

Sheet 2 of 4

1/7/08 IMI-685

INSTALLATION INSTRUCTIONS

IMPORTANT : READ CAREFULLY BEFORE INSTALLING FIXTURE.

NOTE: Specifications and dimensions subject to change without notice

Visit our web site at www.cooperlighting.com

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX [phone] ADH070937

FIG. 4a (Arm Mount)

Pole Cap

Nut Plate

Arm

Drain Hole

In This

Location

Hex Nut

Lock Washer

1/2-13 Threaded Rod.

Max. extension into housing

is 1”.

Cross Sectional View of Fixture Mounted to Pole

FIG. 4b (Internal Mast Arm Mount)

2” or 1 1/2”

Mounting

Tenon

“A”

Flip Clamps

over for 1 1/2” Pipe

Service Lead Wires

Extend Min. 6”

Electrical

Cover

Detail “A”

Tear off this part

of gasket for

2” pipe size

Housing

Stop

Tenon Clamp Bolts (qty. 4)
Torque to 100 inch pounds