Cooper Lighting HWAS1BLE40 User Manual

SMART ANYPLACE BLUETOOTH DIMMER SWITCH

Simple. Secure.

HWAS1BLE40AWH

eaton.com/halohome

SMART ANYPLACE BLUETOOTH DIMMER SWITCH

Simple. Secure.

Wirelessly control smart lights or smart switch

from anywhere in your home.

Must have Halo Home compatible lights installed

and powered to use switch.

Indoor use only.

Press to turn on

Slide up/down for dimming*

Press to turn off

*May also be used with non-dimmable devices.

Removing the back panel

Press thumbs forward on the front of the switch, near the top. The back panel should slide down opposite the switch. Lift the back panel off.

Once the back panel has been removed, insert the 3 provided CR2032 Batteries

(Energizer Lithium recomended) in the location shown with the “positive” side of the battery facing you.

IMPORTANT: The red indicator light should come on for about 1 second and go off. If the light stays on permanently, it is necessary to remove the batteries and reinstall them again. The switch will not function if the light is on permanently.

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

WARNING: The battery (battery or batteries or battery pack) shall not be exposed to excessive heat such as sunshine, ﬁre or the like.

Adding the switch to the APP

• Go to the HALO Home app.

• Press the “ “ menu button in the upper left and navigate to “controllers” and the press the “+” button on the screen.

• Next, Press the button on the Switch so that the red light is ﬂashing

a double ﬂash.

- At this point you should see the switch appear on the screen.

• If the switch does not appear in the screen before the ﬂashing light goes off, then press the button on the switch again and repeat the process.

• Select the switch and press “Done.” It may take up to 30 seconds for this process to complete.

Note: If the switch does not successfully add before the ﬂashing light

goes off, then press the button on the switch again and repeat the process.

• At that point the switch will be added and you will be ready to associate it to a device.

Connect the switch to HALO Home devices

• If you want to associate to a single device, select the “Devices” tab

at the bottom.

- Swipe the device photos left or right until you ﬁnd the device you want.

• To associate to a group of devices, create a group if you have not done so already. Then press the “Groups”

Note: You must create the group before you associate with the switch.

• Next swipe the group photos left or right until you ﬁnd the group you

want.

• If you like, you can give the switch a name and a photo by touching the switch name or photo.

• Before your switch will work, it is necessary to save the conﬁguration to the switch. There are two steps to this process:

1) Hit “Save” in the upper right corner of the app screen.

2) Then, Press the button on the switch.

• Pressing the button on the switch is necessary because the switch circuitry stays “asleep” unless someone is speciﬁcally touching it. This is done to extend the battery life.

• You will know that the switch has properly saved when the app closes the association screen and returns to the controller dashboard, and you will also see the device or group name on the switch dashboard.

IMPORTANT: If you do not press the button on the switch and see the app close the association screen, the changes will not be saved to the switch and it will not work as expected.

Mounting by tape

Attach using the provided screws, or to mount with tape: Find the side of the tape marked “Wall side” and make sure it is facing you.

Remove the opposite side of the tape and stick to the area on the switch marked “Tape”. Push the tab through the slot.

Remove the side of the tape marked “Wall side”.

Make sure the area you want to mount the switch is clean and free from dust. Stick in place and press ﬁrmly for 10 seconds.

Note: Wall mounting is not required. Switch

can also be used as a hand held device.

Removing from the wall

If it is necessary to relocate the switch to a new location: Remove the front plate and set aside.

If afﬁxed with tape: Hold the switch with one hand, and pull the tape tab sideways with the other. Be careful to pull evenly and slowly and as sideways as possible (along the wall surface).

Remove one tape and then the other. If a tape does not fully remove or breaks, twist the back cover slowly and carefully to remove.

DO NOT PULL THE SWITCH OFF THE WALL AS THIS WILL LIKELY DAMAGE THE WALL SURFACE.

If afﬁxed with screws: Simply remove the screws and replace in a different location. The Halo Home Switch uses tape speciﬁcally designed to be removed without damaging wall surfaces. However, each surface is unique.

EATON ASSUMES NO LIABILITY FOR DAMAGE RESULTING FROM REMOVING THE SWITCH.

+ 14 hidden pages