Cooper Lighting HALO miniLUME LA5300, HALO miniLUME LF5300, HALO miniLUME L5300 Installation Instructions Manual

• SAFETY INFORMATION

• IMPORTANT SAFETY
INSTRUCTIONS

• READ CAREFULLY FOR YOUR
PROTECTION AND SAVE ALL
INSTRUCTIONS

• Disconnect power before installing light fixture on track.

• Wear rubber-soled shoes and work on a sturdy wooden ladder.

• This fixture must be installed according to the National Electric

Code and local building codes.

• To avoid a hazard to children, account for all parts and destroy all

packing materials.

• If you are unsure about the installation or use of this fixture con-

sult a qualified electrician.

• CAUTION: To reduce the risk of fire and electrical shock, use only

fixtures and fittings intended for use with Halo and Lazer by Halo
track systems only.

Installation Instructions for LA5300, LF5300
& L5300 Adjustable Beam Lampholders

HALO

®

HALO

®

Operation
This device has an internal ceramic metal halide transformer allowing it to operate
on Halo and Lazer by Halo line voltage track. Make sure you are using the correct
lamp type and wattage for your track fixture. In the event of a shutdown the lamp
will re-strike in approximately 5 minutes

NOTICE: THIS EQUIPMENT CONTAINS A R.F. BALLAST THAT HAS BEEN TESTED AND
FOUND TO COMPLY WITH THE LIMITS PURSUANT TO PART 18C NON-CONSUMER
LIMITS OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE
PROTECTION AGAINST HARMFUL INTERFERENCE WITH ELECTRONIC DEVICES SUCH
AS: RADIOS, TELEVISIONS, WIRELESS TELEPHONES OR REMOTE CONTROLS. IF
INTERFERENCE OCCURS IT MAY BE POSSIBLE TO CORRECT THE INTERFERENCE BY
ONE OR MORE OF THE FOLLOWING MEASURES:

• REORIENT OR RELOCATE ANTENNA OF THE RECEIVING DEVICE.

• INCREASE THE SEPARATION BETWEEN THIS EQUIPMENT AND THE DEVICE.

• CONNECT THIS EQUIPMENT OR THE DEVICE INTO A DIFFERENT OUTLET OR CIR­CUIT.

THIS EQUIPMENT SHOULD NOT BE USED:

• CLOSER THAN THREE (3) FEET FROM ANY SENSITIVE ELECTRONIC EQUIPMENT.

• NEAR MARITIME SAFETY, NAVIGATION, OR COMMUNICATIONS EQUIPMENT.

Service

There are no user serviceable parts inside. Opening unit will void
warranty. Contact point of purchase for service.

Installation Instructions for
L5300 Series Track Fixture (Fig. 1A, 1B, 1C & 1D)

The L5300 track fixture can be used with Halo and Lazer by Halo
single circuit track and Halo-2 two-circuit track. An adjustable con­tact allows you to select the circuit position. Use a narrow blade
screwdriver as shown (Fig.1A) to adjust the contact. Lift or lower
the contact until it touches the upper or lower plastic stop of the
contact assembly.
To use with Halo or Lazer by Halo single circuit track the
adjustable contact must be in the circuit #1 or lower position. To
use with Halo-2 two circuit track adjust the contact position to the
desired circuit position, circuit #1 down or circuit #2 up position
(Fig. 1B).

ADJUSTABLE
CONTACT

FIG. 1A

FIG.1B

Customer First Center • 1121 Highway 74 South • Peachtree City, GA 30269 • 770.486.4800 • FAX [phone]

11/06 rev.4 702505

Customer First Center • 1121 Highway 74 South • Peachtree City, GA 30269 • 770.486.4800 • FAX [phone]

11/06 rev.4 702505

FOCUSING
KNOB

HORIZONTAL
LOCK

9/64" ALLEN
WRENCH

FIG.13

VERTICAL
LOCK

9/64" ALLEN
WRENCH

FIG. 12

FIG. 11

Changing Media

The fixture bezel assembly can accept two clear glass lenses or one color
filter with or without a clear lens.

Focusing Beam

Focus by rotating knob 1/4 turn on fixture. Beam can be adjusted from a
spot to a flood (Fig. 11).

Instructions for Lockable Aiming

Lockable aiming is only available for L530070E series fixtures.

Step 1 Aim fixture to desired position.

Step 2 Insert 9/64 allen wrench, provided by others, into hole under track

adapter. Turn clockwise to tighten. This will lock vertical rotation
(Fig.12).

Step 3 Insert 9/64 allen wrench into hole near on/off switch. Turn clock-

wise to tighten. This will lock horizontal rotation (Fig. 13).

DOWN
POSITION

UP
POSITION

HALO

®

SWITCH

LAMP
(do not twist)

Do not touch
lamp with bare
fingers - hold
lamp with cloth

FIG. 7

FIG. 10

HALO

®

TRACK
POLARITY
GROOVE

INSERT FIXTURE
IN TRACK AND
THEN TWIST 90°

FIXTURE
POLARITY
GROOVE

FIXTURE
POLARITY
GROOVE

THUMB
LATCH

FIG. 1C

FIG. 1D

To install the fixture to the track, insert the contact assembly into the track and
rotate the fixture neck 90° so the polarity line on the power supply aligns with
the polarity line on the track. Pull back and release the thumb latch allowing
the power supply to lock into position (Fig 1C and 1D).

To remove the fixture, slide thumb latch down until latch is clear of the track
channel opening. Twist the fixture neck and turn (90°) until the contact
assembly is free and remove power supply from track.

Installation Instructions for
LA5300 Series Track Fixture (Fig. 2)

The LA5300 track fixture can be used with Halo two circuit Architectural Track.

Fixture can be rotated 180° to second circuit.

To install fixture into track, open switch cover so that contacts are concealed
inside fixture. Insert fixture into track so the contact will engage the desired
circuit. Close switch cover.

To remove fixture, rotate switch cover 90° and remove from track. (Fig. 2)

Installation Instructions for
LF5300 Series Track Fixture (Fig. 3)

The LF5300 track fixture can be used with Halo ‘LF’ series 2 two-circuit track
only.

Step 1. Open connector cover by pulling downward on the connector sleeve

and connector cover so that the contacts are exposed.

Step 2. Raise fixture to track with contacts facing intended circuit.
Step 3. Move connector into position and close connector cover until it snaps

into position.

To remove fixture from track.

Step 1. Open connector cover by pulling downward on the connector sleeve.
Step 2. Raise fixture from track and remove.

Note: To access the other circuit, rotate fixture 180 degrees and follow

installation instruction above.

Relamping Instructions

Warning: Before working on fixture, be sure to turn off AC power or remove

fixture from track.

Step 1 Allow unit to cool then remove from track

Step 2 Remove bezel and glass assembly by rotating assembly counter-

clockwise (Figs 4 & 5).

Step 3 Remove glare shield by pulling both ends of the glare shield straight

out (Fig. 6).

Step 4 Locate the relamp label on the outer surface of the reflector to deter-

mine the required lamp wattage for proper fixture operation (Fig. 6).

Step 5 Remove the existing lamp by pulling straight out.

Step 6 Using a soft cloth to avoid contacting the new lamp with bare hands,

insert the replacement lamp into the socket by carefully aligning the
lamp pins to the socket and pushing the lamp straight into the
socket without twisting (Fig. 7). Insure lamp pins are inserted
properly into the socket for proper lamp function.

FIG. 2

FIG. 3

BEZEL & GLASS
ASSEMBLY

FIG. 4

CONNECTOR COVER

CONNECTOR
SLEEVE

Customer First Center • 1121 Highway 74 South • Peachtree City, GA 30269 • 770.486.4800 • FAX [phone]

11/06 rev.4 702505

Customer First Center • 1121 Highway 74 South • Peachtree City, GA 30269 • 770.486.4800 • FAX [phone]

11/06 rev.4 702505

FIG. 9

REFLECTOR
HOUSING

FIG.8

LUGS

Step 7 Replace the glare shield and bezel and glass assembly by carefully

engaging all three lugs on the bezel with the corresponding lugs on the
reflector housing (Fig. 8). Turn the bezel and glass assembly clockwise
until the positive ‘click’ is felt, indicating the home position has been
engaged in the reflector housing (Fig. 9). Verify the bezel and glass
assembly is securely retained in the reflector housing.

Step 8 DO NOT OPERATE FIXTURE WITHOUT GLASS LENS. RISK OF FIRE.

Be sure on-off switch is returned to ON position (Fig 10).

FIG. 5

FIG. 6

GLARE SHIELD

BEZEL &
GLASS
ASSEMBLY

RELAMP
LABEL