Cooper Lighting H456ICAT120D User Manual

HALO LED H4 Series

The Halo H4 LED is a family of 4” aperture recessed downlight
housings designed for use with Halo EL4 Series LED Light Engines
and compatible 4” LED trims. Halo H4 LED housings have integral
LED drivers that offer dimming as a standard feature.

H456ICAT120D is an insulated ceiling, AIR-TITETM housing offering
120 volt dimming capability with many incandescent or electronic
low voltage dimmers. Designed for use with EL4 series LED Light
Engines and TL4 LED Series Trims, the H456ICAT120D offers high
quality downlighting along with high efficacy – the result being great
lighting and significant energy savings.

DESIGN FEATURES

MECHANICAL

Housings

• Box enclosure of formed
aluminum construction.

• Openings are gasketed
AIR-TITE.

• Designed for insulated ceilings in
direct contact with insulation.
(May also be installed in
non-insulated ceilings.)

Plaster Frame

• Galvanized steel die-formed
construction.

• The housing can be removed from
plaster frame to provide access to
the junction box.

• Plaster frame features include:

- Patented regressed locking screw
positioned for securing hanger
bars from below the ceiling.

- Cutouts for easily crimping
hanger bars in position.

- AIR-TITE aperture gasket is
pre-installed.

- HALO identity embossed on
plaster frame.

GOT NAIL! Pass -N-Thru™
Bar Hangers

• Pre-installed nail easily installs
in regular lumber, engineered
lumber and laminated beams.

• Safety and guidance system
prevents snagging, ensures
smooth straight nail penetration
and allows bar hangers to be easily
removed if necessary.

• Automatic leveling flange aligns
the housing and lets you hold the
housing in place with one hand
while driving nails.

• Housing can be positioned at any
point within 24” joist span.

• Pass-N-Thru™ feature allows bar
hangers to be shortened without
removing from plaster frame.

• Score lines allow “tooless”
shortening for 12” joists.

• Bar hangers may be repositioned
90°.

• Integral T-bar clip snaps onto
T-bars - no additional clips
required.

Slide-N-Side™ Junction Box

• Positioned to accommodate
straight conduit runs

• Seven 1/2” trade size conduit
knockouts with true pry-out slots

• Slide-N-Side™ wire traps allow
non-metallic sheathed cable to be

installed without tools and
without removing knockouts.

• Accepts a wide range of
non-metallic (type NM) sheathed
cables - the standard cable types
used in lighting in both U.S. and
Canada.

- Allows wiring connections to be
made outside the junction box

- Simply insert the cable directly
into the trap after connections
are made.

- Accommodates the following
standard non-metallic sheathed
cable sizes:

(US) #14/2, #14/3, #12/2, #12/3
(Canada) #14/2, #14/3, #12/2

LED Connection

• LED connector is a non-screw base
connector offering easy installation
with the EL4 Series LED Light
Engine.

• LED connector meets California
Title-24 high-efficacy luminaire
requirement for a non-screw
base socket, and where required
to qualify as a high-efficacy
luminaire.

LED Driver

• LED dimmable driver mounts
to the housing.

• Driver is a120 Volt, high efficiency,
electronic power supply providing
low voltage power to EL Series
LED Light Engines.

• Driver meets FCC EMI/RFI
Consumer Level limits for use in
residential and commercial
installations.

• Driver features high power factor
and low THD and has integral
thermal protection in the event
of over temperature or internal
failure.

• Driver is specifically designed
for compatibility with EL4 LED
Light Engines, and operates the
LED for long life, meeting 50,000
hour / 70% lumen maintenance
standard.

• If dimming is not required the
fixture can be operated from a
standard wall switch.

Dimming

• The HALO H4 LED luminaire is
dimmable to 15% with most
standard 120V dimmers;
including LED-rated and
electronic low voltage dimmers
(recommended); many

Catalog #

Project

Comments

Prepared by

incandescent and magnetic low
voltage dimmers; and dims to 5%
using dimmers with low end trim
adjustment.

• Standard incandescent dimmers
require a minimum load of
typically over 40 watts on the
circuit for full range dimming
performance (four LED modules).

• For dimming with digital (smart)
multi-location dimmers or when
dimming fewer than four LED
modules, LED rated or electronic
low voltage dimmers are required
(ELV dimmers need a neutral
connection in the wallbox).

Labels

• UL/cUL Listed 1598 Luminaire

• UL/cUL Listed for Damp Location

• UL/cUL Listed for Wet Location,
covered ceiling - with select trims

• UL/cUL listed for Feed Through

• UL/cUL listed for Direct Contact
with insulation and combustible
material

Compliance

• Use with designated LED light
engines and trims for ENERGY

®

STAR

qualification.

• Can be used for State of California
Title 24 high efficacy compliance
with designated LED light engines
and trims.

• Can be used for International
Energy Conservation Code (IECC)
high efficacy compliance with
designated LED light engines
and trims.

• Refer to specification sheets online
for compliance information.

Qualification

IC and AIR-TITE™
Certified under ASTM-E283 and

listed UL/cUL 1598. May be used to
meet insulated ceiling and restricted
air-flow requirements such as:

• Washington State Energy Code

• International Energy
Conservation Code (IECC)

• New York State Energy
Conservation Construction
Code (NY-ECCC)

• State of California Title 24
“Recessed Luminaires in
Insulated Ceilings.”

HALO

Type

Date

H456ICAT120D

4-Inch LED
Recessed Housing
New Construction

Insulated Ceiling -

With 4” LED Light Engines

and 4” LED Trims

High Efficacy LED Housing-

Dimmable

I N SU LAT E D C E I LI NG S

F O R DI R E CT CO NTA C T

W I TH I N S UL AT I O N

A L SO S U I TA B LE F O R

N O N- IC A P PL IC AT IO N S

H4 Series LED Energy Data:

(Values at non-dimming line voltage.)
Minimum Starting Temp: -30°C (-22°F)
EMI/RFI: FCC Title 47 CFR, Part 18
(Consumer)
Sound Rating: Class A standards
Input Voltage: 120V
Power Factor: >0.90
Input Frequency: 50/60Hz
THD: <20%
Rated Wattage: 15W max.
Input Power: 14.0W
Input Current: 121mA
Driver Compliance: UL6950, LPS rated
Maximum IC (Insulated Ceiling) Ambient
Continuous Operating Room Temperature:
25°C (77°F)
Maximum Non-IC (Non-Insulated Ceiling)
Ambient Continuous Operating Room
Temperature: 40°C (104°F)

H4 Series LED
Summary Lighting Data:

Lumen range: . . . . . . . . . . . . .534-700

Lumens per watt: . . . . . . . . . . up to 46

Color

Correlated Color Temperature

(CCT): . . . . . . . . . . . . . . .2700K-4000K

Color Rendering Index (CRI, Ra): . . . 80

F O R US E IN

®

www.cooperlighting.com

ADV110681

rev 4/8/11

HALO

®

DIMENSIONS

H 4 5 6 I C AT 12 0 D

5-3/8 inch
(136 mm)

outer dimension

1/2 inch
(13 mm)

4-1/4 inch

(108 mm)

8-1/2 inch

(216 mm)

ORDERING INFORMATION
SAMPLE NUMBER: H456ICAT120D EL405827 TL400SC

Complete unit includes LED housing, light engine, and trim, ordered separately

H4 LED Housing

H456

H456=

4˝ Housing
H4 LED Series
Downlight

ICAT=
New Construction,
Insulated Ceilng,
AIR-TITE

Designer Trim Rings, Thin Profile
TRM400WH=White, die-cast trim ring
TRM400BK=Black, die-cast trim ring
TRM400SN=Satin Nickel, die-cast trim ring
TRM400TBZ=Tuscan Bronze, die-cast trim ring
TRM400PC=Polished Chrome, die-cast trim ring

ICAT

120D=

LED driver,
120V, 50/60Hz,
Dimmable - most
standard electronic
low voltage
(recommended)
and incandescent/
magnetic low
voltage dimmers
(see dimming
application notes,
and refer to dimmer
manufacturers for
compatiblity)

120D

EL4=

4˝ LED
Downlight
Light Engine

* Lumen output range of 534-700
lumens (depending upon color
temperature and trim)

Accessories

H4 LED Light Engine

EL4

05

05=

550
Design
Lumens*

8

8=

80 CRI

27=2725°K
30=3045°K
35=3465°K
40=3985°K

6 inch

(152 mm)

H4 LED Trim

27

TL40x

TL400SC= Specular Clear Refector, White Trim Ring
TL400H=Haze Reflector, White Trim Ring
TL400WH=White Reflector, White Trim Ring
TL400SBK=Specular Black Reflector, White Trim Ring
TL400SN=Satin Nickel Reflector, Satin Nickel Trim Ring
TL400TBZ=Tuscan Bronze Reflector, Tuscan Bronze

Trim Ring

TL401WB=White Baffle, White Trim Ring
TL401BB=Black Baffle, White Trim Ring
TL402SCS=Specular Clear Reflector with Solite

White Trim Ring
TL402HS=Haze Reflector with Solite

®

Lens, White Trim Ring

TL402WHS=White Reflector with Solite
White Trim Ring
TL402SBKS=Specular Black Reflector with Solite
White Trim Ring
TL402SNS=Satin Nickel Reflector with Solite
Satin Nickel Trim Ring
TL402TBZS=Tuscan Bronze Reflector with Solite
Tuscan Bronze Trim Ring

TL403WBS=White Baffle with Solite
TL403BBS=Black Baffle with Solite

®

Lens, White Trim Ring

®

Lens, White Trim Ring

®

Lens,

®

Lens,

®

Lens,

®

Lens,

®

Lens,

www.cooperlighting.com

1

t

Standard Dimming Control

120V AC dimmed power
to Halo LED Downlights

Dimmer Types & Representative List of Manufacturers*

Reverse Phase Control - 120VAC  Dimmers

• Electronic Low Voltage rated dimmers are typically Reverse Phase (Trailing Edge)

• ELV rated dimmers provide greater assurance of dimming performance compatibility.*

• Minimum Circuit Load of One LED Module, Dimming to 15% (dimming to 5% with select dimmers as noted)

Require the neutral terminal on the dimmer connected to a neutral in the wall box.

Lutron

Diva® DVELV Series

®

Maestro

MAELV Series

®

Nova

NLV Series

®

Nova T

NTELV & NTLV Series

®

Skylark

SELV Series

®

Vierti

VTELV Series

Forward Phase Control Dimmers - 120VAC

• Incandescent and Magnetic Low Voltage rated dimmers are typiccally
Forward Phase (Leading Edge) Dimmers

• Circuit Load of 4 LED Modules or More, Dimming to 15%

• Forward phase control dimmers are generally compatible and typically
provide acceptable dimming results.*

Cooper Controls

iLumin SC-UN Universal Source Controller Series - Lighting Control Panel System

Cooper Wiring Devices

ASPIRE RF® N/A

™

ASPIRE

9530, 9532, 9538, 9540

Decorator Slide
Decorator Full-Slide
Toggle
Rotary
Architectural Rotary

Cooper Wiring Devices - LED Dimmers (Low End Trim)

ASPIRE 9573
Skye SLC03P
Devine DLC03P

Lutron

Ariadni® AY/TG Series
Ceana
Centurion

™

Dalia

®

DV Series

Diva
Glyder

Leviton

Illumitech™ IPI/RPI Series
Sureslide

Minimum Brightness Adjustment (Low End Trim), Dimming to 5%

Illumitech™ IP10/IP40/IPM406/IPM10 Series dimmers (Manual trim)
Acenti
Vizia + VPI/VPE/VPX Series (Programmable trim)

®

DI06P, DI10P

®

®

6441, 6443, 6453

®

6001, 6013, 6000, 6003, 6020, 6023

™

CN Series

®

C Series

DL Series

®

GL Series

SI061, SI06P, SI10P

®

RAI10, RAI15, RAI20

Lumea™ LG Series

™

LX Series

Lyneo

®

N Series

Nova

®

NT/NTB/NTA Series

Nova T

™

Q Series

Qoto

®

S Series

Skylark

Trimatron™ 6681/6683/6602

™

663 Series

®

ACI/ACE/ACX/ATI Series (Programmable trim)

TrueTouch

™

6606-ILM

Leviton

Minimum Brightness Adjustment (Low End Trim), Dimming to 5%

Acenti® ACE Series (Programmable trim)

™

IllumiTech

IPE Series (Manual trim)

Vizia + VPE Series (Programmable trim)

Lutron - Commerical

Commercial Panel Systems LP-RPM-4A120 Remote Power Module - Adaptive Dimming

Lutron - Whole House

Homeworks HW-RPM-4A-120 Remote Power Module-Adaptive Dimming
HW-RPM-4V-120 Remote Power Module-Dimming
HWD-5NE, HRD-5NE Wired Maestro and RF Maestro Local Controls

Watt Stopper

Miro Universal DRD4 Series Dimmers
DCD267 Series Dimmers
DCD68 Series Multilocation - When used with DRD4 or DCD267 series

master dimmers

• Universal Wireless Dimmers (Incandescent, Magnetic Low Voltage, Electronic Low Voltage)

• Minimum Circuit Load of Two LED Modules, Dimming to 15%

Watt Stopper

Miro Incandescent DRD2 Series Dimmers
DCD26 Series Dimmers
DCD68 Series Multilocation - When used with DRD2 or DCD26

series master dimmers

• Incandescent Wireless Dimmers

• Minimum Circuit Load of Five LED Modules, Dimming to 15%

A 15W minimum incandescent load or a neutral in the wall box may be required to reliably dim

LiteTouch, Inc.

LiteTouch 08-2108-01 Quad dimmer
LiteTouch 08-2134-01 Hybrid dimmer

(LiteTouch recommends the fade times be set for at least 2 seconds on and off for the FIVEk in
the load group parameters. Consult LiteTouch for additional technical application).

Crestron*

CLS-C6(M), CLS-EXP-DIM, CLS-EXP-DIMU, CLX-1DIM4, CLX-1DIM8, CLX-2DIM8, CLX-1DELV4,
DIN-1DIM4, DIN-1DIMU4, GLX-DIM6, GLXX-2DIM8 (Crestron recommends if more than 1 fixture

is connected, set MIN LEVEL=3% to ensure all fixtures turn on simultaneously at low end).
CLW-DIMSWEX, CLW-DIMSWCN, CLW-DIMEX, CLW-DIMCN, P-DIMEX (Consult Crestron for

LED compatibilty and technical application. Require Neutral wire connection at dimmer and
custom firmware).

*Consult Crestron for Control System Min-Max % level Intensity recommendations.

H 4 5 6 I C AT 12 0 D

120V AC Power
(2 wire + Gnd typical)

*Applications Notes

1. LED Dimming performance may vary from incandescent dimming. Performance results may vary based upon dimmer model,
manufacturer, circuit wiring and circuit loading.

2. Dimmer maximum load rating with LED may differ from published Incandescent and Electronic Low Voltage dimmer ratings.
Consult dimmer manufacturer for maximum dimmer load with LED.

3. For special dimming applications consult dimmer manufacturer or controls specialist (e.g. large multiple circuit installations, many
LEDs per circuit, sequenced fades, 277V or 347V circuits powered by step-down transformers, etc.).

4. There are no warranties of performance or compatibilty implied.

5. This is a representative list of dimmers. Refer to dimmer manufacturers for further information on LED compatiblity and finish codes.

Lutron, Leviton, LiteTouch, Crestron, Watt Stopper and their product brand names are registered trademarks of each respective company.

SPECIAL NOTE: Incandescent Digital Dimmers

Incandescent Digital Dimmers (also called Smart or Multi-Location)
require an incandescent load. For circuit loads with LED modules
only - use reverse phase control (electronic low voltage rated)
dimmers.

www.cooperlighting.com

HALO

®

H 4 5 6 I C AT 12 0 D

3 YEAR PRODUCT LIMITED WARRANTY

Cooper Lighting (The Company) warrants
the HALO H4x Series LED housings, Halo
EL4x, ELG4x, ELSGx Series LED Light
Engines, and HALO TL4x, TLS4x Series
LED Trims against defects in material or
workmanship for a period of three years
from date of original purchase, and agrees
to repair or, at the company’s option, re­place a defective product without charge
for either replacement parts or labor dur­ing such time. This does not include labor
to remove or install fixtures.

This warranty is extended only to the origi­nal purchaser of the product. A purchasers
receipt or other proof of date of original
purchase acceptable to the Company is
required before warranty performance
shall be rendered. This warranty only
covers product failure due to defects in
materials or workmanship which occurs
in normal use. It does not cover the failure
of product caused by accident, misuse,
abuse, lack of reasonable care, altera­tion, or faulty installation, subjecting the
product to any but the specified electrical
service or any other failure not resulting

from defects in materials or workmanship.
Damage to the product caused by sepa­rately purchased, non-Company supplied
components and corrosion or discolor­ation of components are not covered by
this warranty. There are no express war­ranties except as described above.

THE COMPANY SHALL NOT BE LIABLE
FOR INCIDENTAL, SPECIAL OR CONSE­QUENTIAL DAMAGES RESULTING FROM
THE USE OF THE PRODUCT OR ARISING
OUT OF ANY BREACH OF THIS WAR­RANTY. ALL IMPLIED WARRANTIES, IF
ANY, INCLUDING IMPLIED WARRANTS
OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE
LIMITED IN DURATION TO THE DURA­TION OF THIS EXPRESS WARRANTY.
Some states do not allow the exclusion
or limitation of incidental or consequential
damages, or limitations on how long an
implied warranty lasts, so the above exclu­sions or limitations may not apply to you.

No other warranty, written or verbal, is
authorized by the Company. This war-

ranty gives you specific legal rights, and
you may also have other rights which vary
from state to state. To obtain warranty
service, please write to Cooper Lighting,
1121 Highway 74 South, Peachtree City,
Georgia 30269. Enclose product model
number and problems you are experienc­ing, along with address and telephone
number. You will then be contacted with a
solution or a Return Goods Authorization
number and full instructions for returning
the product. All returned products must be
accompanied by a Return Goods Autho­rization Number issued by the Company
and must be returned freight prepaid. Any
product received without a Return Goods
Authorization Number from the Company
will be refused. Cooper Lighting is not
responsible for merchandise damaged
in transit. Repaired or replaced products
shall be subject to the terms of this war­ranty and are inspected when packed.
Evident or concealed damage that is made
in transit should be reported at once to
the carrier making the delivery and a claim
filed with them.

www.cooperlighting.com

Solite® is a registered trademark of AGC Flat Glass North America

Note: Specifications and Dimensions subject to change without notice.

Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX [phone]

Cooper Lighting 5925 McLaughlin Rd. Mississauga, Ontario, Canada L5R 1B8 905.507.4000 FAX [phone]

Visit our web site at www.cooperlighting.com