Cooper Lighting Corelite Jaylum Suspended T5, Corelite Jaylum Suspended T8 Installation Manual
JAYLUM
SAVE THESE INSTRUCTIONS
WARNINGS
1) WARNING! – Risk of Fire/Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing.
2) WARNING! – Risk of Fire/Electric Shock. If not qualifiied, consult an electrician.
3) WARNING! – Risk of Fire/Electric Shock. Luminaires wiring, ballasts, or other electrical parts may be damaged when drilling for installation of refl ector kit hardware. Check for
enclosed wiring and components.
NOTES
1) NOTE! – This product must be installed in accordance with local/ national electrical codes.
2) NOTE! – Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of kit installation. Do not leave any other open holes in an
enclosure of wiring or electrical components.
3) NOTE! – To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or any sharp objects.
4) NOTE! – Disconnect all power before proceeding.
Suspended T5/T8 Luminaire
INSTALLATION
CONNECTION AT FIXTURE
CROSS CABLE INSTALLATION
Insert Barrel Terminal
1
into keyhole slot.
Fully insert Toggle into
2
keyhole slot.
Install Screw(s)
3
CABLE/GRIPPER INSTALLATION
12” Aircraft Cable with Barrel Terminals
and Steel Toggles (included).
2
1
POWER FEED
J-BOX
1
(by others)
NON-POWER FEED
Slide Cable Coupler onto Main Suspension Cable
1
and secure Coupler to appropriate mounting point
at ceiling.
Install Cable Gripper onto Main Suspension Cable.
2
Insert Cross Cable into Cable Gripper and install
3
thumbscrew.
Loosen thumbscrew to level xture. Re-tighten
as necessary once xture leveling has been
completed.
Adjust Main Cable to desired length and cut
4
excess cable if necessary.
! IMPORTANT: Install CABLE CRIMP prior to
cutting cable.
Not all options available. Please consult your Cooper Lighting Representative for availability. Specications and Dimensions subject to change without notice.
Cable Coupler
SJT CordCable
Cable Coupler
Cable
2
Please refer to Corelite “Connection at Ceiling” instructions
for detailed information on various mounting methods.
3
Cable Crimp
4
ADE130026
Power
FIXTURE LENGTH
JAYLUM
INSTALLATION
Suspended T5/T8 Luminaire
POWER DROPS / KNOCK-OUTSMOUNT SPACING
SAMPLE ROW
FIXTURE LENGTH
*For continuous rows see joining sheet.
JOINING
Install rst xture with two AC cable
assemblies, then second xture with
one additional cable.
96” SPACING 96” SPACING
Bend out tapered aligning tabs and
t into aligner slots. (Fixture 2 is now
supported by xture 1 at the joint.)
Make electrical connections.
5/8”-7/8” KNOCK OUT
Break o appropriate KO, slide power cord through KO opening, then
secure power cord with strain relief.
Note: Location of the KO’s varies depending on xture
Tuck wires into wire cavity, slide both
xtures together. Secure xtures using
two 10-32 x 3/8” screws and nuts.
Tighten 1/4 turn past hand-tight.
END CAP
End Caps: Slide into end of xture
and secure with two 10-32 x 3/8”
self tapping screws.
Slide-N-Lock
TAB
NOTE: Remove lm from optic before installing.
To Install - set in place over lamps.
The Slide-N-Lock comes pre-set from the factory to the customer specied optical setting.
To eld adjust the optic, depress the control notch and slide tab to desired setting (instructions
located on optic).
TM
TM
INSTALL LAMPS
*T5 Shown
DUST COVER
Set in place.
Not all options available. Please consult your Cooper Lighting Representative for availability. Specications and Dimensions subject to change without notice.
*For continuous rows see joining sheet.
ADE130026
Loading...