MT250 325-1526.qxd 3/13/06 2:03 PM Page 1
Instruction Manual
Instucciones
Directives
MT250W, CMT250W
MT250, CMT250
MT250 325-1526.qxd 3/13/06 2:03 PM Page 2
Congratulations! You have purchased a Cooper Lighting floodlight kit.
The MT250 is constructed with rugged diecast aluminum and should
provide years of trouble free weatherproof service.
Required for installation (not suppplied)
• Screwdriver
• Weatherproof silicone caulking
• (2) 150 watt (MAX) PAR 38 floodlight bulbs (A)
What’s included
• Light fixture (B)
• Coverplate gasket (C)
• Lampholder gaskets (D)
• Wire nuts (E)
• Mounting screws (F)
What to know
PLEASE READ THESE IMPORTANT SAFETY INSTRUCTIONS.
• For outdoor use only.
• cULus Listed for wet location use.
• Fixture must be connected to a 120 volt, 60 Hz power source
(any other connection voids warranty).
• Fixture should be installed by a qualified electrician or by persons with
experience in household wiring. The electrical system, and the method of
electrically connecting this fixture to it, must be in accordance with the
National Electrical Code and local building codes.
• Fixture should be mounted to a grounded junction box marked for use in
wet locations.
• Suitable for wall mount or eave mount only. NOT suitable for ground
mount installation.
• Keep away from flammable objects. Do not position fixture
within one inch of any combustible materials.
• The bulb and fixture get extremely hot during use.
Allow fixture to cool completely before attempting to reposition fixture.
• Always replace bulb with the same wattage or lower wattage than
marked. Installing a bulb of a higher wattage could create a fire hazard.
Use of a higher wattage bulb will void the warranty.
• Your light fixture is prewired for easy installation.
• Disassembly of your fixture will void the warranty
MT250, CMT250 (Bronze)
MT250W, CMT250W (White)
A
C
D
B
E
F
Call for customer service and/or missing or damaged parts (800-334-6871)
2
MT250 325-1526.qxd 3/13/06 2:03 PM Page 3
Installing your fixture
Note: Estimated assembly/installation time is 15 minutes.
Warning: Risk of electric shock. Disconnect power at fuse or
circuit breaker before installing or servicing.
Step 1: This mounting plate has been designed to work with a variety of
different junction boxes. Line up the holes in the mounting plate with
the screw bosses in your junction box.
Note: If holes in mounting plate do not match the screw bosses in your junction
box, drill holes in the mounting plate using an 1/8” drill bit to match screw
bosses in junction box.
Step 2: Take the gasket (C) included with this mounting plate and position it
behind the mounting plate. Line up the screws in the mounting plate
with the appropriate hole pattern in the gasket and remove gasket
material in those holes.
Step 3: Connect lampholder wires to supply wires from house (white to white
and black to black) using wire nuts (E). Attach the ground wire from
your house to the copper colored wire (coming from the fixture cover
plate) using a wire nut. The electrical system, and the method of
electrically connecting the fixture to it, must be in accordance with the
National Electrical Code and building codes.
Step 4: Attach the mounting plate to your junction box using the screws
provided (F), making sure that the gasket is properly aligned and that
all screws are tightly secured. To prevent moisture from entering the
junction box, apply a bead of silicone sealant around the edge of the
mounting plate where it attaches to the junction box and any open
holes.
Warning: Risk of burn. Disconnect power and allow fixture to cool
before changing bulb or handling fixture.
Step 5: Insert gaskets (D) into lampholders and screw bulbs (A) into
lampholders (do not overtighten bulbs).
Step 6: Turn power on at main fuse/breaker box.
Aiming the light
Loosen the knob on the side of the light housing. Tilt fixture head up or
down to desired position then retighten knob.
SAVE THESE INSTRUCTIONS.
Two Year Limited Warranty
Cooper Lighting (“the Company”) warrants this product (“the product”) against
defects in material or workmanship for a period of two years from date of original purchase, and agrees to repair or, at the Company’s option, replace a defective product without charge for either replacement parts or labor during such
time. This does not include labor to remove or install fixtures.
This warranty is extended only to the original purchaser of the product.
A purchasers receipt or other proof of date of original purchase acceptable to
the Company is required before warranty performance shall be rendered.
Call for customer service and/or missing or damaged parts (800-334-6871)
3
MT250 325-1526.qxd 3/13/06 2:03 PM Page 4
This warranty only covers product failure due to defects in materials or
workmanship which occurs in normal use. It does not cover the bulb or failure
of the product caused by accident, misuse, abuse, lack of reasonable care,
alteration, or faulty installation, subjecting the product to any but the specified
electrical service or any other failure not resulting from defects in materials or
workmanship. Damage to the product caused by separately purchased, nonCompany brand replacement bulbs and corrosion or discoloration of brass
components are not covered by this warranty.
There are no express warranties except as described above.
THE COMPANY SHALL NOT BE LIABLE FOR INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE
PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL
IMPLIED WARRANTIES, IF ANY, INCLUDING IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED IN DURATION TO THE DURATION OF THIS EXPRESS WARRANTY.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty lasts, so
the above exclusions or limitations may not apply to you.
No other warranty, written or verbal, is authorized by the Company.
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
To obtain warranty service, please write to: Cooper Lighting, 1121 Highway 74
South, Peachtree City, GA 30269. Enclose product model number and problems you are experiencing, along with your address and telephone number. You
will then be contacted with a solution, or a Return Goods Authorization number
and full instructions for returning the product. All returned products must be
accompanied by a Return Goods Authorization Number issued by the Company
and must be returned freight prepaid. Any product received without a Return
Goods Authorization Number from the Company willbe refused.
Cooper Lighting is not responsible for merchandise damaged in transit.
Repaired or replaced products shall be subject to the terms of this warranty and
are inspected when packed. Evident or concealed damage that is made in transit should be reported at once to the carrier making the delivery and a claim
filed with them.
Reproductions of this document without prior written approval of Cooper Lighting are strictly prohibited.
Call for customer service and/or missing or damaged parts (800-334-6871)
1121 Highway 74 South, Peachtree City, GA 30269
Customer First Center
www.cooperlighting.com
© 2008 Cooper Lighting, LLC
Printed in USA
4
Loading...