Cooper Lighting AMETRIX P4R User Manual
Vault
These installation instructions are valid with the above Ametrix styles.
C-Scroll
Roundel
Installation Instructions
Sheet 1 of 2
Small, INDOOR
P4R
(P
endant, 4-way, Remote ballast
Visor and Non-Visor
Warning
that all sources of power are turned off. All
work must meet local/national codes and be
performed by a certified electrician.
mount fixtures vertically.
: Before starting any work ensure
Do not
)
Exploded view and part call-out
J-box
(by others)
#8-32 x3/8"
1/4" Fastener
Canopy
Cover plate
Quad fixture assemblies require additional bracing/structure
around J-box to support fixture.
2
1/4-20 x4 1/2"
Hex cap bolts
(4x)
Attention:
Wiring the fixture
Set screw
(2x)(4x)
1/4-20 x 4 1/2"
Hex cap bolts
(4x)
Fixture wire
Cover plate
1
Cover plate
1.
Remove all 1/4-20 x4 1/2" hex bolts from bottom of pendant.
2.
Remove both #8-32 x 3/8" set screws and allow canopy to
slide down pendant.
3.
Run wires from J-box into pendant, ensure there is enough
wire to reach cover plate.
4.
Using appropriate fasteners, secure fixture to ceiling.
additional bracing around J-box to support fixture.
5
. Replace canopy and secure using both set screws.
3
Fixture head
indicator
Mounting pendant to J-box
1/4" fasteners (by others)
(by others)
(4x)
#8-32 x3/8"
Set screw
(2x)
J-box
Use additional bracing
around J-box to support
fixture.
Canopy
Aiming the fixture
1/4-20 x4 1/2"
Hex cap bolts
(4x)
Use
1.
With pendant secure, slide fixture assembly onto pendant
and secure with four 1/4-20 x4 1/2" hex bolts.
2.
Remove cover plate and insert wires from fixture heads into
pendant and pull through opening.
3.
Attach appropriate wires and ensure all connections are
properly matched.
4.
Push connections into pendant and secure cover plate.
ADY071466 REV B(ECN80481)
Yoke arm
indicator
1.
To aim fixtures, loosen both #10-32 end screws on
fixture. When both indicators are lined up, the slope of the
lens face is 40-degrees. Each subsequent notch is an
additional +/- 10-degrees.
2.
When fixture head is rotated to the desired angle, retighten
end screws to secure the position.
3.
Repeat for remaining fixture heads.
one
Vault w/ visor
LAMP
These installation instructions are valid with the above Ametrix styles
C-Scroll w/ visor
Roundel w/ visor
Installation Instructions
Sheet 2 of 2
Small, INDOOR
P4R
(P
endant, 4-way, Remote ballast
)
Visor and Non-Visor
Warning
that all sources of power are turned off. All
work must meet local/national codes and be
performed by a certified electrician.
mount fixtures vertically.
: Before starting any work ensure
Do not
1
"
2
12.70
Mounting Plate Dimensions In [mm]
Length dependant
on order
6"
152.40
1
"
4
2
114.30
50.80
1
4
2
114.30
Front ViewSide View
2"
"
152.40
6"
3
"
4
19.05
19.05
3
"
4
13
32
10.16
(4x)
"
Lamping Size Chart
(lamps provided by others)
FIXTURE SIZE
(inches/ mm)
10 3/4 / 273.05 39 W 1 T6 Ceramic Metal Halide
12 3/4 / 323.85 70 W 1 T6 Ceramic Metal Halide
12
/ 323.85 150 W 1 T6 Ceramic Metal Halide
3/4
12
/ 323.85 26 W 1
3/4
12
/ 323.85 32 W 1
3/4
12
/ 323.85 42 W 1
3/4
10 3/4 / 273.05 100 W 1 T4 Halogen (Single Ended)
12 3/4 / 323.85 150 W 1 T4 Halogen (Single Ended)
12 3/4 / 323.85 250 W 1 T4 Halogen (Single Ended)
WATTAGE
# OF
LAMPS
LAMP TYPE LAMP DESCRIPTION
4-Pin Triple
Tube
4-Pin Triple
Tube
4-Pin Triple
Tube
Compact Fluorescent
Compact Fluorescent
Compact Fluorescent
(not to scale)
Use only GE or Sylvania
CFL lamps
ADY071466 REV B(ECN80481)
Loading...