Cooper Lighting AMETRIX P1R User Manual

Vault

These installation instructions are valid with the above Ametrix styles.

C-Scroll

Roundel

Installation Instructions

Sheet 1 of 2

Small, OUTDOOR

P1R

(P

endant

, 1

-way

, R

emote ballast

Visor and Non-Visor

Warning

that all sources of power are turned off. All
work must meet local/national codes and be
performed by a certified electrician.
mount fixtures vertically.

: Before starting any work ensure

Do not

)

J-box
(by others)

#8-32 x3/8"
Set screw
(2x)

#6-32 x 5/8"
Set screw

2

Exploded view and part call-out

1/4" fasteners
(by others)

Canopy

Compression
fitting

#10-32 x5/8"
#6-32 x1/2"
Set screw
(2x)

End screw

(2x)

Wiring & sealing the fixture

1

J-box
(by others)

#8-32 x 3/8"
Set screw
(2x)

1.

Using both #10-32 x5/8" end screws, secure fixture head to
yoke on pendant and run wire through compression fitting
and into pendant.

2.

Remove both #10-32 x3/8" set screws and allow canopy to
slide down pendant.

3.

Run wires from pendant and j-box through wiring holes in
mounting plate.

4.

Using appropriate fasteners, secure fixture to ceiling.

additional bracing around J-box to support fixture.

3

Securing fixture to ceiling

Use additional bracing
around J-box to support
fixture.

1/4" fasteners
(by others)
(x4)

Canopy

Use

Aiming the fixture

#6-32 x1/2"
set screw
(2x)

#6-32 x5/8"
set screw

1.

After securing fixture to ceiling, attach appropriate wires

and ensure all connections are properly matched.

2.

Push wire connections into j-box and cover mounting plate

with canopy.

3.

Secure canopy using both #10-32 x3/8" set screws.

4.

To seal door, refer to torque sequence supplementry page.

ADY071467 REV B(ECN80481)

#10-32 x3/8"
set screw
(2x)

Fixture head
indicator

1.

To aim fixture, loosen both #10-32 x5/8" end screws. When
both indicators are lined up, the slope of the lens face is 40­ degrees. Each subsequent notch is an additional +/- 10­ degrees

2.

When fixture head is rotated to desired angle, retighten end
screws to secure the position.

Yoke arm
indicator

#10-32 x5/8"
End screw
(2x)

Vault w/ visor

LAMP

These installation instructions are valid with the above Ametrix styles

C-Scroll w/ visor

Roundel w/ visor

Installation Instructions

Sheet 2 of 2

Small, OUTDOOR

P1R

(P

endant, 1-way, Remote ballast

)

Visor and Non-Visor

Warning

that all sources of power are turned off. All
work must meet local/national codes and be
performed by a certified electrician.
mount fixtures vertically.

: Before starting any work ensure

Do not

7

16

11.42

Mounting Plate Dimensions In [mm]

1

"

1"

25.40

"

4"

101.60

Length dependant

on order

5"

127

4"

5"

101.60

127

Side View Top View

2

12.70

1"

25.40

12.70

1
4

6.35

1
2

"

"

(4x)

Lamping Size Chart

(lamps provided by others)

FIXTURE SIZE

(inches/ mm)

10

/ 273.05 39 W 1 T6 Ceramic Metal Halide

3/4

12

3/4

/ 323.85 70 W 1 T6 Ceramic Metal Halide

12

3/4

/ 323.85 150 W 1 T6 Ceramic Metal Halide

12

3/4

/ 323.85 26 W 1

12

/ 323.85 32 W 1

3/4

12

3/4

/ 323.85 42 W 1

10

3/4

/ 273.05 100 W 1 T4 Halogen (Single Ended)

12

/ 323.85 150 W 1 T4 Halogen (Single Ended)

3/4

12

/ 323.85 250 W 1 T4 Halogen (Single Ended)

3/4

WATTAGE

# OF

LAMPS

LAMP TYPE LAMP DESCRIPTION

4-Pin Triple

Tube

4-Pin Triple

Tube

4-Pin Triple

Tube

Compact Fluorescent

Compact Fluorescent

Compact Fluorescent

(not to scale)

Use only GE or Sylvania

CFL lamps

ADY071467 REV B(ECN80481)