Cooper Lighting ADY071478 User Manual
Vault
These installation instructions are valid with the above Ametrix styles.
C-Scroll
Roundel
Installation Instructions
Sheet 1 of 2
Small, INDOOR
CR
(C
antilever
, R
emote ballast
)
Visor and Non-Visor
Warning
that all sources of power are turned off. All
work must meet local/national codes and be
performed by a certified electrician.
mount fixtures vertically.
: Before starting any work ensure
Do not
Exploded View and part call-out
#8-32 x3/8"
Set screw
(2x)
Mounting
plate
#10-32 x5/8"
End screw
Fixture head
(2x)
Attention:
All cantilever fixture assemblies require additional
bracing/structure around J-box to support fixture.
2
Wiring the fixture
1
Use additional bracing around
J-box to support fixture
Fixture
wire
1.
Secure fixture head to pendant yoke using both #10-32 x5/8"
end screws.
2.
Feed fixture wire through pendant tube.
3.
Remove both #8-32 x3/8" set screws and slide canopy down
pendant.
4.
Run wires from pendant and j-box through wiring holes in
mounting plate.
5.
Use appropriate fasteners, secure mounting plate to structure
around J-box.
support fixture.
3
Securing the fixture to structure
J-box
(by others)
Fasteners
(by others)
#8-32 x3/8"
Set screw
(2x)
Use additional bracing around J-box to
(4x)
Aiming the fixture
#8-32-3/8"
Set screws
(2x)
Wiring holes
1.
After securing fixture to structure, attach appropriate wires
and ensure connections are properly matched.
2.
Push wire connections into J-box and cover mounting plate
with canopy.
3.
Secure canopy with both #8-32-3/8" set screws.
#10-32 x5/8"
End screw
Yoke arm
indicator
1. To aim fixture, loosen both #10-32 x5/8" end screws. When
both indicators are lined up, the slope of the lens face is 40 degrees. Each subsequent notch is an additional +/- 10 degrees
2. When fixture head is rotated to desired angle, retighten end
screws to secure the position.
Fixture head
indicator
ADY071478 REV B (ECN80481)
Vault w/ visor
LAMP
These installation instructions are valid with the above Ametrix styles
C-Scroll w/ visor
Roundel w/ visor
Installation Instructions
Sheet 2 of 2
Small, INDOOR
CR
(C
antilever, Remote ballast
)
Visor and Non-Visor
Warning
that all sources of power are turned off. All
work must meet local/national codes and be
performed by a certified electrician.
mount fixtures vertically.
: Before starting any work ensure
Do not
7
16
11.42
Mounting Plate Dimensions In [mm]
1"
1
"
2
12.70
25.40
1
"
4"
"
Length dependant
101.60
2
12.70
on order
1"
25.40
5"
127
1
" (4x)
4
4"
6.35
101.60
5"
127
Side View Top View
Lamping Size Chart
(lamps provided by others)
FIXTURE SIZE
(inches/ mm)
10
3/4
/ 273.05 39 W 1 T6 Ceramic Metal Halide
12
3/4
/ 323.85 70 W 1 T6 Ceramic Metal Halide
12
3/4
/ 323.85 150 W 1 T6 Ceramic Metal Halide
12
/ 323.85 26 W 1
3/4
12
/ 323.85 32 W 1
3/4
12
/ 323.85 42 W 1
3/4
10
3/4
/ 273.05 100 W 1 T4 Halogen (Single Ended)
12
/ 323.85 150 W 1 T4 Halogen (Single Ended)
3/4
12
3/4
/ 323.85 250 W 1 T4 Halogen (Single Ended)
WATTAGE
# OF
LAMPS
LAMP TYPE LAMP DESCRIPTION
4-Pin Triple
Tube
4-Pin Triple
Tube
4-Pin Triple
Tube
Compact Fluorescent
Compact Fluorescent
Compact Fluorescent
(not to scale )
Use only GE and Sylvania
CFL lamps
ADY071478 REV B (ECN80481)
Loading...