Cooper Lighting ADY071464 User Manual
Vault
These installation instructions are valid with the above Ametrix styles.
C-Scroll
Roundel
Installation Instructions
Sheet 1 of 2
Small, INDOOR
P1R
(P
endant
, 1
-way
, R
emote ballast
Visor and Non-Visor
Warning
that all sources of power are turned off. All
work must meet local/national codes and be
performed by a certified electrician.
mount fixtures vertically.
: Before starting any work ensure
Do not
)
J-box
(by others)
1/4" fasteners
(by others)
Fixture
head
2
Exploded view and part call-out
#10-32 x3/8"
Set screw(2x)
Wiring holes
Canopy
#10-32 x5/8"
End screw
(2x)
Wiring the fixture
1
1/4" fasteners
(by others)
(4x)
1.
Using both #10-32 x5/8" end screws, secure fixture head to
yoke on pendant and run fixture wire through pendant.
2.
Remove both #10-32 x3/8" set screws and allow canopy to
slide down pendant.
3.
Run wires from pendant and j-box through wiring holes in
mounting plate.
4. Use
Using appropriate fasteners, secure fixture to ceiling.
additional bracing around J-box to support fixture.
3
Mounting the fixture
Use additional bracing
around J-box to support
fixture.
#10-32 x3/8"
Set screw(2x)
Canopy
Yoke
#10-32 x5/8"
End screw
(x2)
Aiming the fixture
#10-32 x3/8"
Set screw
(2x)
1. After securing fixture to ceiling, attach appropriate wires and
ensure all connections are properly matched.
2. Push wire connections into j-box and cover mounting plate
with canopy.
3. Secure canopy using both #10-32x 3/8" set screws.
ADY071464 REV B (ECN80481)
Fixture head
indicator
1. To aim fixture, loosen both #10-32 x5/8" end screws. When
both indicators are lined up, the slope of the lens face is 40 degrees. Each subsequent notch is an additional +/- 10 degrees
2. When fixture head is rotated to desired angle, retighten end
screws to secure the position.
Yoke arm
indicator
#10-32 x5/8"
End screw
(2x)
Vault w/ visor
LAMP
These installation instructions are valid with the above Ametrix styles
C-Scroll w/ visor
Roundel w/ visor
Installation Instructions
Sheet 2 of 2
Small, INDOOR
P1R
(P
endant
, 1
-way
, R
emote ballast
)
Visor and Non-Visor
Warning
that all sources of power are turned off. All
work must meet local/national codes and be
performed by a certified electrician.
mount fixtures vertically.
: Before starting any work ensure
Do not
7
16
11.42
Mounting Plate Dimensions In [mm]
1
"
1"
25.40
4"
101.60
Length dependant
on order
5"
127
4"
101.60
5"
127
Side View Top View
2
12.70
1"
25.40
"
1
4
6.35
1
"
2
12.70
"
(4x)
Lamping Size Chart
(lamps provided by others)
FIXTURE SIZE
(inches/ mm)
10
/ 273.05 39 W 1 T6 Ceramic Metal Halide
3/4
12
/ 323.85 70 W 1 T6 Ceramic Metal Halide
3/4
12
/ 323.85 150 W 1 T6 Ceramic Metal Halide
3/4
12
/ 323.85 26 W 1
3/4
12
/ 323.85 32 W 1
3/4
12
/ 323.85 42 W 1
3/4
10
/ 273.05 100 W 1 T4 Halogen (Single Ended)
3/4
12
/ 323.85 150 W 1 T4 Halogen (Single Ended)
3/4
12
/ 323.85 250 W 1 T4 Halogen (Single Ended)
3/4
WATTAGE
# OF
LAMPS
LAMP TYPE LAMP DESCRIPTION
4-Pin Triple
Tube
4-Pin Triple
Tube
4-Pin Triple
Tube
Compact Fluorescent
Compact Fluorescent
Compact Fluorescent
(not to scale )
Use only GE or Sylvania
CFL lamps
ADY071464 REV B (ECN80481)
Loading...