Cooper B-Line B3110-2, B3110-21/2, B3110-3, B3110-31/2, B3110-4 User Manual
...
Pipe Rollers & Roller Supports
Fig. B3110 - Adjustable Steel Yoke Pipe Roll (TOLCO Fig. 324)
Size Range: 2" (65mm) thru 24" (600mm) pipe
Material: Cast iron and steel
Function: For supporting pipe where movement may occur due
to thermal expansion.
ovals:
Appr
192A, Type 44, 1"
A-A-1
Conforms to Federal Specification WW
(25mm) thru 20" (500mm), and Manufacturers
-H-171E &
E
Standardization Society ANSI/MSS SP-69 & SP-58, Type 43. Included
in our Seismic Restraints Catalog approved by the State of California
Office of Statewide Health Planning and Development
(OSHPD). For
additional load, spacing and placement information relating to OSHPD
projects, please refer to the Cooper B-Line/TOLCO Seismic Restraint
Systems Guidelines.
Note: When pipe line is insulated, total outside diameter of pipe
and covering should be used to determine size of hanger; also see
B3160 to B3165.
F
Finish: Plain. Contact Cooper B-Line for alternative finishes and
materials.
der By:
Or
Figure number
, pipe size and finish
Note: Not for continuous cycling applications.
Pipe Size Rod Size B C D E
Part No.
B3110-2 2" (50)
B3110-21/2 21/2" (65)
B3110-3 3" (80)
B3110-31/2 31/2" (90)
B3110-4 4" (100)
B3110-5 5" (125)
B3110-6 6" (150)
B3110-8 8" (200)
B3110-10 10" (250)
B3110-12 12" (300)
in. (mm) A in. (mm) in. (mm) in. (mm) in. (mm)
3
/8"-16 19/16" (39.7) 43/4" (120.6) 23/8" (60.3) 17/16" (36.5)
1
/2"-13 17/8" (47.6) 6" (152.4) 33/16" (81.0) 2" (50.8)
1
/2"-13 23/16" (55.6) 65/8" (168.3) 31/2" (88.9) 2" (50.8)
1
/2"-13 21/2" (63.5) 71/4" (184.1) 33/4" (95.2) 2" (50.8)
5
/8"-11 23/4" (69.8) 77/8" (200.0) 4" (101.6) 2" (50.8)
5
/8"-11 33/8" (85.7) 93/16" (233.4) 49/16" (115.9) 2" (50.8)
3
/4"-10 315/16" (100.0) 103/8" (263.5) 51/16" (128.6) 2" (50.8)
3
/4"-10 51/16" (128.6) 125/8" (320.7) 61/16" (154.0) 2" (50.8)
7
/8"-9 61/4" (158.7) 1415/16" (379.4) 73/16" (182.6) 21/16" (52.4)
7
/8"-9 73/8" (187.3) 173/8" (441.3) 83/8" (212.7) 21/4" (57.1)
B3110-14 14" (350) 1"-8 81/4" (209.5) 19" (482.6) 83/4" (222.2) 21/4" (57.1)
B3110-16 16" (400) 1"-8 91/4" (234.9) 203/4" (527.0) 93/4" (247.6) 2" (50.8)
B3110-18 18" (450) 1"-8 103/8" (263.5) 2311/16" (601.7) 117/16" (290.5) 211/16" (68.3)
B3110-20 20" (500) 11/4"-7 111/2" (292.1) 257/8" (657.2) 121/4" (311.1) 21/2" (63.5)
B3110-24 24" (600) 11/2"-6 1313/16" (350.8) 319/16" (801.7) 15" (381.0) 31/2" (88.9)
A
(Rod Size)
Hanger Rod Not
Included
D
C
B
Center of axle to
center of pipe.
Center of axle to
top of hanger steel.
Center of pipe to
bottom of hanger rod.
op of pipe to bottom
T
of hanger rod nut.
B
C
D
ake-Out
Rod T
E
Adjustment
Approx. Wt./100
Lbs.
(kg)
Part No.
in.
F
(mm)
Maximum O.D. Covering
in.
(mm)
Design Load
lbs.
(kN)
B3110-2 27/8" (73.0) 25/8" (66.7) 150 (.67) 123 (55.8)
B3110-21/2 31/4" (82.5) 3" (76.2) 225 (1.00) 178 (80.7)
B3110-3 37/8" (98.4) 35/8" (92.1) 310 (1.38) 206 (93.4)
B3110-31/2 43/8" (111.1) 41/8" (104.8) 390 (1.73) 267 (121.1)
B3110-4 47/8" (123.8) 411/16" (119.1) 475 (2.11) 344 (156.0)
B3110-5 515/16" (150.8) 53/4" (146.0) 685 (3.04) 600 (272.1)
B3110-6 7" (177.8) 63/4" (171.4) 780 (3.47) 800 (362.9)
B3110-8 9" (228.6) 83/4" (222.2) 780 (3.47) 1300 (589.7)
B3110-10 111/8" (282.6) 103/4" (273.0) 965 (4.29) 1600 (725.7)
B3110-12 133/8" (339.7) 13" (330.2) 1200 (5.34) 2600 (1179.3)
B3110-14 141/2" (368.3) 141/4" (361.9) 1200 (5.34) 3400 (1542.2)
B3110-16 163/8" (415.9) 161/8" (409.6) 1200 (5.34) 3900 (1769.0)
B3110-18 183/8" (466.7) 181/8" (460.4) 1400 (6.23) 4900 (2222.6)
B3110-20 203/8" (517.5) 201/8" (511.2) 1600 (7.11) 6686 (3032.7)
B3110-24 245/8" (625.5) 243/8" (619.1) 1800 (8.00) 11630 (5275.3)
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
105
Notes: If using D.I. pipe
refer to page 295 for
sizing. Non-metallic rollers
with stainless steel yoke
and hardware are available
for most sizes (B3110NMÂPipe Size). Contact Cooper
B-Line Engineering for
more information.
Pipe Supports
Pipe Rollers &
Loading...