Cooper B-Line 1CBS, 120RWA, 25, 98, 98B User Manual

...

Seismic System Attachments

Fig. 1CBS - Clevis Bolt Spacer (Cooper B-Line B3100PS)

Size Range: Size 1" (25mm) thru 20" (500mm) clevis hanger

Material: Steel

Function: Used as a spacer at a seismic brace location to

keep clevis hanger from collapsing during seismic event.

Approvals: Included in our Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD). For additional load, spacing and placement information relating to OSHPD projects, please refer to our Seismic Restraint Systems Guidelines.

Installation Note: Fig. 1CBS fits easily over the cross bolt and attaches by pinching tabs down.

Finish: Pre-Galvanized. Contact B-Line for alternative finishes and materials.

Attachments

Order By:

Pipe Size Approx. Wt./100 Part No. in. (mm) lbs. (kg)

Seismic System

Figure

number and finish.

1CBS-1 1”

1CBS-11/4 11/4” (32) 4.1 (1.8)

1CBS-11/2 11/2” (40) 4.8 (2.2)

1CBS-2 2” (50) 9.4 (4.2)

1CBS-21/2 21/2” (65) 11.4 (5.2)

1CBS-3 3” (75) 13.9 (6.8)

1CBS-31/2 31/2” (90) 16.0 (7.2)

1CBS-4 4” (100) 18.0 (8.1)

1CBS-5 5” (125) 27.3 (12.4)

1CBS-6 6” (150) 32.5 (14.7)

1CBS-8 8” (200) 42.5 (19.2)

1CBS-10 10” (250) 72.7 (32.9)

1CBS-12 12” (300) 86.3 (39.1)

1CBS-14 14” (350) 157.6 (71.5)

1CBS-16 16” (400) 183.7 (83.3)

1CBS-18 18” (450) 224.6 (101.9)

1CBS-20 20” (500) 254.0 (115.2)

(25) 3.2 (1.4)

Component of State of

California OSHPD Approved

Seismic Restraints System

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

Seismic Bracing Products

Fig. 120RWA - (Model B) Retrofit Wrap Around “U” Hanger Clamp

Size Range: 1" (25mm) thru 8" (200mm) pipe

Material: Steel

Function: Designed to restrain movement of the pipe within standard

U-hangers as required by NFPA 13. Where retrofit capability is crucial, the Fig. 120RWA is a labor efficient alternative to the standard B-Line Fig. 120W wrap around U-hanger.

Features Installs easily by tightening two hex nuts. Features a unique bracing slot that locks onto a standard U-hanger to become a solid unit that will stabilize the pipe during seismic activity or sprinkler head activation. Designed to be used in retrofit or new construction applications. Will clamp to existing U-Hangers without restriction to leg angle.

Approvals: Underwriters Laboratories listed in the USA (UL) and Canada (cUL) as a restrainer. Included in our Seismic Restraints Catalog approved by

the State of California Office of Statewide Health Planning and Development (OSHPD). For additional load, spacing and placement information relating to OSHPD projects, please refer to our Seismic Restraint Systems Guidelines. NFPA 13 (2010) 9.3.6.3.

Finish: Plain and Galvanized. Contact B-Line for alternative finishes and materials.

Order By: Figure number, type numbers and pipe size

Ordering Note: Order by the following type and pipe size:

Type 1 — (1" Type 2 — (1

(25mm) and 1

⁄2" (40mm) and 2" (50mm) pipe size)

⁄4" (32mm) pipe size)

Type 3 — (21⁄2" (65mm) and 3" (80mm) pipe size) Type 4 — (4" (100mm) pipe size) Type 6 — (5" (125mm) and 6" (150mm) pipe size) Type 8 — (8"

(200mm) pipe size)

Component of State of

California OSHPD Approved

Seismic Restraints System

Important Note: The bracing slot feature is sized to fit the U-Hanger rod schedule as required by NFPA 13 as follows:

⁄16" (7.9mm) rod for up to 2" (50mm) pipe

⁄8" (9.5mm) rod for 21/2" (65mm) - 6" (160mm) pipe

⁄2" (12.7mm) rod for 8" (200mm) pipe

For other rod size requirements consult factory.

Type Pipe Size

Part No.

in. (mm)

120RWA-TYPE1-1 1 1" (20)

120RWA-TYPE1-1

120RWA-TYPE2-11/2

1 11/4

2 11/2

" (25)

" (40)

120RWA-TYPE2-2 2 2" (50)

120RWA-TYPE3-21/2

3 21/2

" (65)

120RWA-TYPE3-3 3 3" (80)

120RWA-TYPE4-31/2

4 31/2

" (90)

120RWA-TYPE4-4 4 4" (100)

120RWA-TYPE6-5 6 5" (125)

120RWA-TYPE6-6 6 6" (150)

120RWA-TYPE8-8 8 8" (200)

Attachments

Seismic System

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

Seismic Bracing Products

Seismic System Attachments

Fig. 25 - Surge Restrainer

Size Range: — One size fits 3⁄4"

Material: — Pre-Galvanized Steel

Function: — Designed to be used in conjunction with Fig. 200 band hangers

to restrict the upward movement of piping as it occurs during sprinkler head activation or earthquake type activity. The surge restrainer is easily and efficiently installed by snapping into a locking position on the band hanger. This product is intended to satisfy the requirements as indicated in the National Fire Protection Association NFPA 13, 2010 edition, 9.2.3.4.4.1 and 9.2.3.4.4.4 Can be used to restrain either steel pipe or CPVC plastic Pipe.

Approvals: — Underwriters Laboratories Listed only when used with band hanger Fig. 200, in the USA (UL) and Canada (cUL).

Finish: Pre-Galvanized

Order By: Figure number and band hanger, size from

⁄4"

(20mm)

thru 2"

(40mm)

Patent #5,344,108

(20mm)

thru 2"

(40mm)

pipe.

Seismic System

Attachments

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

Seismic Bracing Products

Fig. 98 - Rod Stiffener Fig. 98B - Rod Stiffener with Break-Off Bolt Head

Size Range: Secures 3⁄8"-16 thru 7⁄8"-9 hanger rod

Material: Steel

Function: Secures channel to hanger rod for vertical seismic bracing.

Approvals: Included in our Seismic Restraints Catalog approved

by the State of California Office of Statewide Health Planning and Development (OSHPD). For additional load, spacing and placement information relating to OSHPD projects, please refer to our Seismic Restraint Systems Guidelines

Finish: Electro Galvanized. Contact B-Line for alternative finishes and materials.

Component of State of

California OSHPD Approved

Seismic Restraints System

Fig. 98

Weight: Approx. Wt./100: Fig. 98 - 11.8 Lbs.

(5.3kg)

Fig. 98B - 12.7 Lbs. (5.7kg)

Order By: Figure number

Fig. SC228 - Hanger Rod Stiffener

Size Range: Secures 3⁄8"-16 thru 5⁄8"-11 hanger rod

Material: Steel

Function: Secures channel to hanger rod for vertical seismic bracing.

Finish: Electro Galvanized. B-Line for alternative finishes

Weight: Approx. Wt./100: 21.0 Lbs.

Order By: Figure part number

Note: Order channel separately

Slight distortion of the channel (strut) may occur upon installation of rod stiffeners.

and materials.

(9.5kg)

SC228B

11/2”

(63.5)

Fig. 98B

/8”-16

Threads

SC228BS

N228WO

Attachments

Seismic System

Rod Stiffener Requirements

Rod Maximum Rod Length Maximum Spacing Between

Size Without Rod Stiffener Rod Stiffeners

/8” 19” (482mm) 13” (330mm)

1/2” 25” (635mm) 18” (457mm) 5/8” 31” (787mm) 23” (584mm) 3/4” 37” (940mm) 28” (711mm) 7/8” 43” (1092mm) 33” (838mm) 1”* 50” (1270mm) 38” (965mm)

11/4”* 60” (1524mm) 43” (1092mm)

* Use with SC228 only.

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

Seismic Bracing Products

Notes:

1.) Rod stiffeners are required only on hanger and

trapeze assemblies that have seismic bracing attached at or within 4” (101.6mm) of the rod. A minimum of two rod stiffeners (Figure 98, 98B, or SC228) must be installed.

2.) Recommended torque on Figure 98 and SC228

is 8 ft-lbs. (10.8Nm) or finger tight and one full turn with a wrench. Figure 98B has the break off bolt head.

Seismic System Attachments

Fig. 4A - Pipe Clamp for Sway Bracing

Size Range: 4" 4"

(100mm)

Material: Steel

Function: For bracing pipe against sway and seismic disturbance.

Approvals: Underwriters Laboratories Listed in the USA (UL) and Canada (cUL) 4"

approved by the State of California Office of Statewide Health Planning and Development (OSHPD).

Installation Instructions: Fig. 4A is the "braced pipe" attachment component of a longitudinal or riser brace assembly. It is intended to be combined with the "bracing pipe" and our transitional and structural attachment component(s) to form a complete bracing assembly. NFPA 13 and/or OSHPD guidelines should be followed.

To Install: Place the Fig. 4A over the pipe to be braced. Attach our transitional fitting, either Fig. 980, 910 or 909, to the clamp ears. Tighten bolts and nuts; torque requirement is a minimum of 50 ft./lbs. Transitional fitting attachment can pivot for adjustment to proper brace angle.

Finish: Plain or Electro-Galvanized. Contact B-Line for alternative finishes and materials.

Order By: Figure number, pipe size and finish

use B3140.

(100mm)

thru 8"

(200mm)

pipe. For sizes smaller than

. Included in our Seismic Restraints Catalog

(68Nm)

per MSS-SP-58 (2009).

Component of State of

California OSHPD Approved

Seismic Restraints System

HHCS and Hex Nuts Included

Seismic System

Attachments

Fig. 4A - Longitudinal

Brace

Pipe Max. Horizontal Approx.

Part Size A C D Bolt Design Load (UL) Wt./100 No. in. (mm) in. (mm) in. (mm) in. (mm) Size lbs. (kN) lbs. (kg)

4A-4 4" (100) 81/2" (215.9) 33/8" (85.7) 311/16" (93.7) 1/2"-13 1600 (7.11) 221 (100.2)

4A-5 5" (125) 93/4" (247.6) 37/8" (98.4) 43/8" (111.1) 1/2"-13 1600 (7.11) 253 (114.7)

4A-6 6" (150) 111/2" (292.1) 5" (127.0) 51/8" (130.2) 1/2"-13 2015 (8.96) 513 (232.7)

4A-8 8" (200) 131/4"(336.5) 611/16" (169.9) 61/8" (155.6) 1/2"-13 2015 (8.96) 601 (272.6)

Eaton’s B-Line Business seismic bracing components are designed to be compatible only with other B-Line bracing components, resulting in a listed seismic bracing assembly. B-Line’s warranty for seismic bracing components will be the warranty provided in B-Line’s standard terms and conditions of sale made available by B-Line, except that, in addition to the other exclusions from B-Line’s warranty, Eaton’s B-line Business makes no warranty relating to B-Line’s seismic bracing components that are combined with products not provided by Eaton’s B-Line Business.

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

Seismic Bracing Products

Figure 4B Pipe Clamp for Sway Bracing (Cooper B-Line B386)

Size Range:3⁄4” (20mm) to 8” (200mm) pipe

Material: Steel

Function: For bracing pipe against sway and seismic disturbance

Approvals: Included in the Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD).

Standard Finish: Plain or Electro-Plated, Contact B-Line for alternative

finishes and materials.

Ordering: Specify part number and finish.

Installation Instructions: Fig. 4B is the “braced pipe” attachment

component of a longitudinal or lateral sway brace assembly. It is intended to be combined with the “bracing pipe” and transitional and structural attachment component(s) to form a complete bracing assembly. NFPA 13 and/or OSHPD guidelines should be followed.

To Install: Place the Fig. 4B over the pipe to be braced. Attach other transitional fitting, Fig. 909, 910, or 980. Tighten bolts and nuts. Transitional fitting attachment can pivot for adjustment to proper brace angle.

Component of State of

California OSHPD Approved

Seismic Restraints System

Shown with two Cooper B-Line

Fig. 980’s and Schedule 40 brace

pipe.

Hanger/Longitudinal Brace

Pipe Size Rod Size B C D Bolt Size Design Load

Fig. 4B

Approx. Wt./100

Part No. in. (mm) A in. (mm) in. (mm) in. (mm) Lbs. (kN) Lbs. (kg)

4B-3/4 3/4" (20) 3/8"-16 1" (25.4) 27/8" (73.0) 25/8" (66.7) 5/16"-18 330 (1.47) 56 (25.4)

4B-1 1" (25) 3/8"-16 1" (25.4) 31/4" (82.5) 215/16" (74.6) 5/16"-18 330 (1.47) 60 (27.2)

4B-11/4 11/4" (32) 3/8"-16 1" (25.4) 39/16" (90.6) 31/4" (82.5) 5/16"-18 330 (1.47) 74 (33.5)

4B-11/2 11/2" (40) 3/8"-16 1" (25.4) 313/16" (96.8) 37/16" (87.3) 5/16"-18 330 (1.47) 79 (35.8)

4B-2 2" (50) 3/8"-16 11/2" (38.1) 51/8" (130.2) 45/8" (117.5) 5/16"-18 440 (1.78) 156 (70.7)

4B-21/2 21/2" (65) 1/2"-13 13/4" (44.4) 55/8" (142.9) 53/8" (136.5) 3/8"-16 440 (1.78) 176 (79.8)

4B-3 3" (80) 1/2"-13 17/8" (47.6) 63/4" (171.4) 61/8" (155.5) 3/8"-16 660 (2.93) 198 (89.9)

4B-31/2 31/2" (90) 1/2"-13 2" (50.8) 71/4" (184.1) 63/4" (171.4) 3/8"-16 660 (2.93) 219 (99.3)

4B-4 4" (100) 5/8"-11 2" (50.8) 85/8" (219.1) 71/4" (184.1) 1/2"-13 800 (3.56) 288 (130.6)

4B-5 5" (125) 5/8"-11 2" (50.8) 97/8" (250.8) 85/16" (211.1) 5/8"-11 980 (4.36) 390 (176.9)

4B-6 6" (150) 3/4"-10 21/8" (54.0) 1015/16" (277.8) 91/2" (241.3) 5/8"-11 980 (4.36) 448 (203.2)

4B-8 8" (200) 7/8"-9 21/8" (54.0) 137/16" (341.2) 111/2" (292.1) 3/4"-10 1200 (5.34) 691 (313.4)

Attachments

Seismic System

All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.

Seismic Bracing Products

+ 12 hidden pages

Cooper B-Line 1CBS, 120RWA, 25, 98, 98B User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual