Page 1
Oil Switches
Types VR, VCR, VLR
Maintenance Instructions
Figure 1. Type VR,VCR and VLR electr onicall y contr olled three phase oil s witch.
S260-20-9
Service Information
CAUTION: Do not energize this
!
equipment out of oil.
CONTENTS
Introduction . . . . . . . . . . . . . . . . . 1
General Description . . . . . . . . . . 1
Description of Operation . . . . . . 3
Standard Actuator . . . . . . . . . . . . 3
Quick-Close Actuator . . . . . . . . . 4
Ratings and Specifications . . . . 5
Maintenance . . . . . . . . . . . . . . . . 5
Frequency of Maintenance . . . . . 5
Periodic Maintenance Inspection . 5
Operating Instructions . . . . . . . . 6
Electrical Operation . . . . . . . . . 6
Standard Actuator . . . . . . . . . 6
Quick-Close Actuator . . . . . . . 6
Manual Operation . . . . . . . . . 6
To Close Switch . . . . . . . . . 6
To open Switch . . . . . . . . . . 6
Oil Condition . . . . . . . . . . . . . . 6
Insulation Level Withstand Tests 6
Shop Repair Procedures . . . . . 7
Bushings . . . . . . . . . . . . . . . . . 7
Contacts . . . . . . . . . . . . . . . . . 7
Type VR and VCR Switches .8
T ype VLR Switches . . . . . . . . 11
Actuator Mechanism . . . . . . . . 13
Electrical Components . . . . . 13
Trip Solenoid . . . . . . . . . . . . 14
Motor Replacement . . . . . . . 15
Speed Reducer . . . . . . . . . . 15
Service Parts List ..................... 17
Tank and Head Assembly Parts
(Figure 39) .......................... 18
Type VR Contact Assembly Parts
(Figure 40) .......................... 20
Type VCR Contact Assembly Parts
(Figure 41) .......................... 21
Type VLR Contact Assembly Parts
(Figure 42) .......................... 22
Actuator Mechanism Parts
(Figure 43) .......................... 24
Quick-Close Mechanism Parts
(Figure 44) .......................... 26
These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide
directions for meeting every contingency during installation, operation, or maintenance. When additional information is desired to
satisfy a problem not covered sufficiently for the user’s purpose, please contact your Cooper Power Systems sales engineer.
September 1983 ●New Issue
Printed in USA
1
Page 2
INTRODUCTlON
Service Information S260-20-9 covers
the maintenance instructions for Types
VR VCR, and VLR motor operated oil
switches. This includes their general
description, operating principles and
instructions for periodic inspection, testing, trouble shooting and shop repairs.
A service parts list, keyed to exploded
view drawings of the equipment is
included at the back of the manual.
NOTE: Maintenance instructions for early
(pre1970) versions of these switches is covered in the original service bulletin 28710SB-1.
GENERAL DESCRIPTlON
These oil-filled, electrically-operated
devices provide, three-phase switching
for general purpose loads (Type VR)
capacitive loads (Type VCR) and inductive loads (Type VLR) on manual or
automatic command. These switches
utilize a common operating mechanism
and package configuration, and are differentiated by their contact assemblies.
The Type VCR switch utilizes a set of
wedge-shaped moving contacts for arcing and a set of bayonet-type contacts
for load-carrying. In addition, resistors in
series with the arcing contacts damp
both the magnitude and frequency of
transient inrush currents for parallel
capacitor bank switching applications
(Figure 2).
The Type VR switch utilizes two sets
of wedge-shaped moving contacts, one
set for arcing and the second for loadcarrying (Figure 3).
The Type VLR switch utilizes a set of
bayonet-type moving contacts which
operate within self-blast interrupterchambers for quick and effective arc
interruption when switching inductive
loads (Figure 4).
The contact structures for all three
phases are linked with bell cranks to a
common torque shaft operated by the
actuator mechanism located in the cabinet on the front of the switch.
Figure 2. Untanked Type VCR switch.
Figure 3.
Type VR contact arrangement.
Figure 4.
Type VLR contact arrangement.
2
Page 3
DESCRIPTION OF
OPERATION
Standard Actuator
These switches are equipped with a
motor-operated actuator mechanism
(Figure 5) for remote closing. Remote
tripping is accomplished by energizing a
trip-open solenoid which unlatches a
spring-loaded operating mechanism to
open the main switch contacts. Subsequent closing is accomplished by operating the motor which loads the opening
springs, latches the operating mechanism, and extends the opening spring
until it overtoggles and closes the main
switch contacts. Time of the closing
operation is approximately 10 seconds.
A mechanical schematic diagram
showing a single set of contacts connected to a straight line motion linkage
and a stored energy actuator is used to
illustrate operating principles. With the
contacts closed (Figure 6), the opening
spring is held extended by a rigidly
latched toggle mechanism. When the
opening circuit is energized, the trip
solenoid breaks the latch to collapse
the toggle and open the main contacts
(Figure 7). Both springs are relaxed; the
contacts cannot be tripped closed accidentally.
When the closing circuit is energized,
the motor operates to drive the crankarm on the gear reduction which
extends the toggle until it latches and
extends both the opening and closing
springs (Figure 8). Fur ther travel of the
crank arm overtoggles the closing
spring to close the switch and carry the
rigid toggle (and extended opening
springs) to the position shown in Figure
6, ready for another trip operation.
The selector switch provides orderly
transition from trip to close and from
close to trip.The selector switch is operated from the main shaft. When the
main contacts are closed the trip circuit
is enabled and the close circuit is disabled. When the main switch contacts
are open the trip circuit is disabled and
the close circuit is enabled. Figure 9
shows the circuit diagram for the standard actuator.
Figure 5. Standard actuator .
Figure 6.
Status of mechanism with switch
closed.
Figure 8. Status of mechanism during closing operation.
S260-20-9
Figure 7.
Status of mechanism with switch
open.
Figure 9. Standard actuator circuit diagram.
3
Page 4
Quick-Close Actuator
When equipped with the quick-close
actuator (Figure 10) the main switch
contacts close in 2.5 to 5 cyc/es after
energizing the closing circuit (compared
to 10 seconds for the standard operator). However, at least 10 seconds lapse
between an opening and closing operation to allow the motor operator to
preload the closing springs. The accessory includes a cam-operated cutout
switch to allow the motor to preload the
closing mechanism and a solenoidoperated latch to release the preloaded
closing mechanism.
With the contacts closed, mechanism
status is the same a shown in Figure 6.
When the opening circuit is energized,
the trip solenoid breaks the latch to collapse the toggle and open the switch
contacts (Figure 7). At the same time,
the closing motor is energized and
drives the crank arm to extend the toggle until it latches and extends both the
opening and closing springs. The closing mechanism is latched in the preloaded position by the closing solenoid
(Figure 11). When the closing circuit is
energized the closing solenoid releases
the overtoggled mechanism to close the
switch and return the mechanism to the
status shown in Figure 6.
Figure 12 shows the circuit diagram
for a control equipped with the quickclose feature with the main contacts
open. A close signal energizes the
quick-close coil, closing the main switch
contacts. The selector switch is operated to the left to disable the quick-close
coil circuit and enable the trip circuit. An
open operation energizes the trip coil,
opening the main switch contacts. The
selector switch is operated to the right
to disable the open circuit and the
cutout switch is operated to the left to
energize the motor.The motor operates
to preload the closing spring. At the
completion of this operation the cam on
the crank arm operates the cutout
switch to the right to de-energize the
motor.
Figure 10. Quick-close actuator.
Figure 11. Status of actuator with closing spring preloaded.
Figure 12. Quick-close actuator circuit diagram.
4
Page 5
S260-20-9
RATINGS AND SPECIFICATIONS
Table 1
Electrical Ratings
Rated maximum voltage (kv rms) 15.5
Nominal system voltage (kv rms) 2.4-14.4
Rated impulse withstand voltage
(BIL) (kv cress) 110
60-Hz insulation level withstand (kv rms)
Dry, 1 minute 50
Wet, 10 seconds 45
Rated continuous current (amps) 400
Table 2
Load Switching Ratings
Switch Power Current
Type Application Factor (amps)
VR Capacitive current
switching — 300
7.2 kv 14.4 kv
Inductive load 75-100 400 200
switching 50-75 200 100
10-50 100 50
VCR Capacitive current
switching* — 400
VLR Inductive load
switching 10-100 400
Table 3 Short-Time Current Ratings
Rated momentary asymmetrical current (amps) 20,000
Rated 1/2-second symmetrical current (amps) 13,500
Rated 1-second symmetrical current (amps) 10,000
Rated 4-second symmetrical current (amps) 6,000
Rated asymmetrical making current (amps) 20,000
Rated
MAINTENANCE
Frequency of Maintenance
Because these switches are applied
under widely varying operating and climatic conditions, maintenance intervals
are best determined by the user based
on actual operating experience. Cooper
Power Systems recommends the switch
be inspected and serviced yearly until
experience indicates a more advantageous schedule. In no case should the
service interval extend beyond 1200
operations.
Periodic Maintenance
Inspection
Each periodic maintenance inspection
should include at least the following:
1. By-pass and remove the switch from
service.
2. Inspect external components.
A. Clean the bushings and inspect
for chips, cracks and breaks.
Replace as necessary. (See
page 7 for procedure.)
B. Check for paint scratches and
other mechanical damage. Paint
to inhibit corrosion.
3. Perform a dielectric withstand test to
determine the insulation level. (See
page 6 for procedure.)
4. Loosen the head bolts and remove
the mechanism from the tank. Be
careful not to damage the gasket, if
the tank and head must be pried
apart to break the seal.
5. Allow the oil to drain off the mechanism.
6. Clean the internal components.
A. Remove all traces of carbon by
wiping with a clean, lint-free
cloth.
B. Flush the inter nal components
with clean transformer oil.
Table 4 Actuator Operating Data
Closing motor:
Nominal operating voltage (vac) 120
operating voltage range (vac) 95-130
Inrush current (amps) 6
Stead-state current (amps) 3
Running time (see) 10
Trip coil current at 120 vac (amps) 5
CAUTION: Never use
!
volatile solutions, detergents,
or water-soluble cleaners.
7. Check the moving and stationary
contacts.
A. Slight pitting and discoloration can
be dressed with crocus cloth or a
fine-tooth file.
B. Replace
tionary contacts if they are
severely eroded. (See page 7 for
procedures.)
NOTE: The contacts should be
replaced before erosion of the loadcurrent transfer surfaces impairs their
effectiveness.
8. Manually close and trip the switch
several times to check that all components perform properly. (See page
6 for manual closing procedure.)
9. Inspect the tank wall liners. Soft or
spongy areas indicate that water has
both
the moving and sta-
5
Page 6
been absorbed. Replace liners if
this condition is detected or even
suspected.
10. Check the dielectric strength of the
insulating oil.
A. A sample taken near the bottom
of the tank should have a
dielectric strength of not less
than 22 kv rms.
B. Low dielectric strength indicates
the presence of water or carbon
deposits; replace the oil. (See
Oil Condition.)
11. If oil must be replaced, drain the
tank and discard the tank wall liners.
12. Thoroughly clean out all sludge and
carbon deposits and rinse the tank
with clean oil.
13. Install new tank wall liners and fill
the tank with clean, new insulating
oil to within 1-1/4” of the top of the
tank flange. Oil capacity is approximately 19 gallons.
NOTE: Use only new, or like new reconditioned transformer oil which conforms
to the specifications in Cooper Power
Systems Reference Data R280 901, “Oil
Specifications and Test”.
14. Clean and examine the head gasket. Replace if it is damaged or has
taken a permanent set.
15. Clean the head gasket seat and
retank the switch.
A. Replace the head bolts and
torque to 12-15 ft-lbs. Apply
clamping force gradually and
equally, in rotation, to each bolt
to achieve an evenly distributed
gasket sealing pressure.
NOTE: Maximum gap between tank
flange and head casting shall be
3/16 inch.
16. Check the oil level with the dipstick
in the head and adjust the level to
the upper line on the stick.
17. Electrically operate the switch to
check for proper operation.
18. Repeat the high voltage dielectric
withstand test (Step 3) to make
sure the dielectric clearances within the tank have not been compromised.
Operating Instructions
ELECTRICAL OPERATION
The switch may be opened and closed
electrically by applying rated operating
voltage directly to the terminal block of
the actuator. See nameplate for rated
operating voltage for the control.
Standard Actuator
Refer to the connection diagram for the
standard actuator (Figure 9) and proceed as follows:
TO CLOSE SWITCH—Apply rated
operating voltage across terminals 2
and G long enough for the motor to
complete its closing cycle (approximately 10 seconds).
TO OPEN SWITCH—Momentarily
apply rated operating voltage across
terminals 3 and G to energize the trip
solenoid.
Quick-Close Actuator
Refer to the connection diagram for the
quick-close actuator (Figure 12) and
proceed as follows:
TO CLOSE SWITCH—Apply rated
operating voltage across terminals 1
and G. If the closing spring is not
preloaded, the motor will operate to
extend the spring (approximately 10
seconds). When closing spring is
preloaded, temporarily jumper terminals
1 and 2 to energize the quickclose
solenoid.
TO OPEN SWITCH—Apply rated operating voltage across terminals 3 and G
to energize the trip solenoid.
MANUAL OPERATION
A crank is included in the bottom of the
actuator cabinet for closing the switch
manually.
To Close Switch
STANDARD ACTUATOR—Apply crank
to shaft on the front of the mechanism
(Figure 13) and turn crank clockwise
until the closing spring overtoggles and
closes the switch (approximately 42
turns).
QUICK CLOSE ACTUATOR — Apply
crank to shaft on the front of the mechanism (Figure 13) and turn crank clockwise until the closing spring drive crank
hits its mechanical stop (approximately
42 turns). Then mechanically operate
the quickclose solenoid to release the
spring and close the switch.
Figure 13. Manually cranking actuator to close switch.
To Open Switch
For both the standard and quick-close
actuators, pull down the pull ring underneath the actuator cabinet to mechanically operate the trip solenoid.
Oil Condition
Oil plays an important role in the proper
functioning of the switch. It provides the
internal insulating barrier between phases and from phase to ground, and acts
as an arc quencher. Switching operations cause reductions of some of the
oil into chemical compounds, free carbon and gases. Some of these compounds form water-absorbing particles
which reduce the dielectric strength of
the oil. For effective switch operation the
oil must be replaced before it deteriorates below a safe level. OiI that has
been contaminated with carbon sludge
or has a dielectric strength of less than
22 kv should be replaced.
Used oil must be reconditioned
before using. Filtering may remove
absorbed and free water, and other contaminants to raise the dielectric strength
to an acceptable level. However, it does
not always remove water absorbing
contaminants. Thus, the dielectric
strength of the oil may fall rapidly after
the switch is returned to service. Therefore the switch should be filled with new
oil or oil that has been restored to likenew condition. Oil used in these switches conforms to ASTM Standard D3487,
Type l; its property limits are listed in
Reference Data R280-90-1; ”Oil Specifications and Tests”.
New oil should always be filtered
before using even though it is obtained
from an approved source. Passing oil
through a blotter press will remove free
water and solid contaminants such as
rust, dirt, and lint. When filtering the oil,
aeration should be kept to a minimum to
prevent moisture in the air from condensing in the oil and lowering its
dielectric strength.
Insulation Level Withstand Tests
High-potential withstand tests provide
information regarding the dielectric condition of the switch.Testing is performed
at 75% of the rated low-frequency withstand voltage (37.5 kv). Proceed as follows:
TEST 1: Proceed as follows:
1. Close the switch.
2. Ground switch tank and head.
3. Connect together all three bushings
on one side of the switch.
4. Apply test voltage (37.5 kv) to the
connected bushings.
• The switch should withstand the
test voltage for 60 seconds.
6
Page 7
TEST 2: Proceed as follows:
1. Close the switch.
2. Ground switch tank and head.
3. Ground the outer two bushings
(Phase A and Phase C).
4. Apply test voltage (37.5 kv) to the
center bushing (Phase B).
• The switch should withstand the
test voltage for 60 seconds.
TEST 3: Proceed as follows:
1. Open the switch.
2. Ground switch tank and head.
3. Connect and ground all three bush-
ings on one side of the switch.
4. Connect together the three bush-
ings on the other side of the switch.
5. Apply test voltage (37.5 kv) to the
ungrounded side of the switch.
• The switch should withstand the
test voltage for 60 seconds.
6. Reverse the test and ground connections to the bushings.
7. Again apply test voltage (37.5 kv) to
the ungrounded bushings.
• The switch should withstand the
test voltage for 60 seconds.
TEST RESULTS: These high potential
withstand tests provide information on
the dielectric condition of the switch.
A. If the switch passes the closed con-
tacts tests (Test 1 and 2) but fails
the open contacts test (Test 3) the
cause is likely to be in one or more
of the main contact assemblies.
B. If the switch fails the closed con-
tacts tests (Test 1 and 2) the cause
is likely to be a diminished electrical clearance or failed insulation.
C. After correcting the problem, retest
to confirm the repair.
SHOP REPAIR PROCEDURES
The procedures described in this section should be performed under the
cleanest possible conditions.No special tools are required for any of the
repair procedures.
Bushings
Bushing replacement generally consists of a thorough cleaning and careful examination for chips, cracks, or
other mechanical damage during the
periodic maintenance inspection.
Bushings must be replaced whenever
damage is discovered.
Note that the contact structures are
supported from the bottom of the
bushings. If more than one bushing is
damaged, replace only one bushing at
a time to maintain contact alignment.
To replace a bushing refer to Figure
14 and proceed as follows:
1. With the switch untanked, remove
the nut, lockwasher and flatwasher holding the contact structure to
the lower end of the bushing rod.
Figure 14. Bushing parts.
2. Remove the three hex head cap-
screws and clamps that secure the
bushing to the head and lift out the
complete bushing assembly.
3. Remove and discard the lower bushing gasket.
4. The complete bushing assembly can
be replaced or new porcelain only
can be installed depending upon the
extent of damage. If new porcelain
only is to be installed, proceed as
follows:
A. Unscrew the bushing terminal
and withdraw the rod from the
bottom of the porcelain; discard
the terminal gasket.
B. Inser t the rod assembly all the
way into the new porcelain, making sure the roll pin is seated in
the locking groove in the top of
the bushing.
C. Assemble the terminal to the
bushing rod using a new terminal
gasket; tighten to a torque of 35
ft-lbs.
NOTE: Apply a very small amount of
petroleum jelly to the knurled surface
of the inside face of the terminal
before assembling the terminal to the
bushing rod.
5. Twist off the split aluminum clamping
ring from the old bushing and reuse
if it is in good condition; replace the
ring if damaged.
NOTE: The clamping ring cushions and
distributes the pressure between the
porcelain and the clamps.DO NOT OMIT.
S260-20-9
6. Install the bushing assembly (new or
reworked) into the head casting
using a new lower bushing gasket.
Position the bushing with the studend of the terminal pointing outward.
7. Position the clamping ring with the
split centered between two clamping bolts.
8. Reassemble the bushing to the head
casting. Tighten the clamping bolts
evenly, a little at a time, to a torque
of 6-10 ft-lbs.
NOTE: Clamping forces must be applied
gradually and equally in rotation to each
bolt. This results in an evenly distributed
gasket sealing pressure.
9. Reconnect the bushing to the contact structure.
10. Recheck contact alignment as specified on page 9 or 12.
Contacts
The Type VR switch utilizes two sets of
wedge-shaped moving contacts; one set
for arcing, the second set for load-carrying (Figure 3). The Type VCR switch utilizes a set of wedge-shaped contacts for
arcing, a set of bayonet-type contacts
for load carrying, and resistors in series
with the arcing contacts for damping
capacitor switching transients (Figure
2). Contact service and alignment pro-
cedures are similar for both switches.
7
Page 8
NOTE: The contact structure for Type VCR
switches below serial 1770 uses wedgeshaped contacts for load-carrying as well as
arcing. It is strongly recommended that these
old-style contact assemblies be replaced
with the updated version.A contact assembly
kit, KA704VCR is available for this pur pose.
Three kits are required per switch. Instructions for replacing the contact structure are
included in the kit.
The Type VLR switch utilizes a set of
bayonet-type moving contacts which
operate within self-blast interrupter
chambers (Figure 4). Separate ser vice
and alignment procedures are included
for the T ype VLR switch.
Contact service and alignment will be
greatly simplified if the head assembly
is inverted; bushings down. The head
assembly can be supported on its bushings.
TYPE VR AND VCR SWITCHES
If it has been determined that the contacts must be replaced, refer to Figures
15 or 16, as appropriate, and proceed
as follows.
1. Remove and discard the moving contact assembly by removing the two
screws and stop nuts that attach the
assembly to the contact rod.
2. Remove the stationary contact
assembly.
A.Type VR switch (Figure 15)
(1) Remove the hardware that
attaches the stationary contact assembly block to the
contact support housing and
discard the entire contact
assembly.
Type VCR switch (Figure 16)
(1) Disconnect the resistor from
the bracket attached to the
arcing contact assembly.
(2) Remove the attaching hard-
ware that secures the entire
stationary contact assembly
to the contact housing.
(3) Remove the spacer, the arc-
ing contact assembly and
the insulator.
(4) Complete the disassembly by
removing the stud, lockwasher, and load-carrying
contact assemblies.
(5) Discard the arcing and load-
carrying contact assemblies.
Figure 15. Type VR contact structure.
Figure 16. Type VCR contact structure.
8
Page 9
S260-20-9
3. Inspect the contact support housing
and contact rod for damage. If
replacement is not required proceed
to step 5. If replacement is required,
proceed as follows:
A. Disconnect the contact rod from
the operating link by removing the
C-ring and link pin. (Figure 17)
Figure 17. Contact rod linkage.
B. Remove the outer hex nut, lock-
washer and flat washer from the
bushing rod and lift contact housing
off the bushing rods.
C. To remove the contact rod from the
housing drive out the roll pin and
pull off the movable contacts
anchor block.(Figure 18)
D.Replace the damaged assemblies
and reassemble the contact rod
to the housing.
4. Reinstall the contact support housing
and contact rod.
A. Set the contact housing assembly
on the bushing rods. See Figure
2 to determine the proper orientation of the damping resistors on
each phase of the Type VCR
switch.
B. VisualIy check that the contact
housing support brackets are
approximately centered on the
bushing rods.
C. Reassemble the flat washers,
lockwashers and outer hex nuts
to both bushing rods. Check that
a flat washer is assembled above
and
below each contact support
bracket. Jam nuts should be
snugged down but not tightened
completely until after contact
alignment has been completed.
D. Reconnect the contact rod to the
operating link with the link pin;
secure the pin with a C-ring.
E. With the switch mechanism in the
open position, the top edge of
the dashpot piston on the contact rod should be approximately
1/32 inch above the top surface
of the dashpot. (See Figure 19.)
Adjust the nuts on the bushing
rods to move the contact housing up or down as required.
5. Reassemble the stationary contact
assembly using new contacts.
A.T ype VR switch
( 1 ) Attach the block of the new
stationary contact assembly
to the support housing with
the hardware removed in
step 2A(1).
Figure 19. Initial adjustment.
B.T ype VCR switch
(1) Attach the load-carrying con-
tact assembly to the support
housing with the studs and
internal tooth lockwashers
removed in step 2B(4).
(2) Reassemble the insulator,
arcing contact assembly and
spacer onto the studs and
secure with the attaching
hardware removed in step
2B(2).
(3) Reconnect the resistor to the
bracket.
6. Install a new moving contact assembly to the anchor block of the bushing rod and secure with the screws
and stop nuts removed in step 1.
7. Align the contact assemblies.
A. Using a combination square
placed across the machined
edges of the head casting,
square the edge of the contact
housing with the head casting as
shown in Figure 20. obtain proper alignment by adjusting the
inner
hex nut.
NOTE: The “sailboat” alignment fixture described on page 40 can be
used to square VR and VCR contact
structures.
Figure 18. Contact rod removal.
9
Page 10
Figure 20. Lateral vertical alignment.
B.With the contact housing squared,
tighten both outer hex nuts without disturbing the position of the
inner nuts.
C. Using a flat plate spanning the
head casting as a base, square
the side of the contact housing
as shown in Figure 21. If not
square the contact housing can
be forced into the squared position.
D. Unhook the closing spring from
the drive stud on the front of the
actuator mechanism. Install the
manual closing crank and crank
clockwise untiI the drive stud
reaches 7 o’clock position;
approximately 42 revolutions.
E. Crank slowly from this point, to
bring the moving contacts toward
the stationary contacts.
NOTE: If the switch is equipped with
the quick-close feature, the mechanism will latch in the 7 o’clock position. To release, push the plunger of
the quickclose solenoid up into the
solenoid.
F. As the moving arcing contacts
approach engagement with the
stationary contacts, observe their
alignment. See Figures 22 and
23. The moving contacts in Figure 22 will engage the stationary
contacts evenly, making simultaneous contact on both sides and
with equal contact force. The
moving contacts in Figure 23
might make entry into the stationary contacts but with unequal
contact force.
Contact misalignment can be
corrected by twisting the moving
contact assembly about its shaft.
The link at the end of the contact
rod will permit enough twist to
obtain the required adjustment.
Figure 23. Contacts misaligned.
G. Viewing the contact assembly
from the end of the switch, as in
Figure 24, check that the moving contacts are entering
squarely into the moving contacts. A visual check that the
moving contact bar is parallel to
the edge of the housing is adequate assurance of this adjustment.
If adjustment is needed,
loosen the two stop nuts slightly
and shift the moving contact
bar.Tighten stop nuts securely.
Figure 21.
Longitudinal vertical alignment.
10
Figure 22.
Contacts aligned.
Figure 24.
Moving contact bar must be parallel to end of contact housing.
Page 11
H. To confirm proper contact
engagement, crank the actuator
mechanism to the fully closed
position. Check clearance
between the moving contact bar
and the contact rod guide block,
Figure 25. Clearance must be
between 1/32 and 1/16 inch.
If clearance is outside these
limits adjust the hex nuts on the
bushing rods to move the stationary contact assembly up or down
as required. Often, a half turn of
each nut provides the adjustment
required
Be careful to move the contact
housing evenly so as not to disturb its vertical alignment.
I. With the housing adjusted to pro-
vide the required gap, tighten the
bushing rod nuts securely. Hold
the inner nut in place with one
wrench while tightening the outer
nut with another wrench.
NOTE: Recheck the clearance (Step
H) and the vertical alignments (Steps
A and B) after bushing rod nuts are
tight.
J. After all three phases have been
reworked, reconnect the closing
spring to the drive stud.
Figure 25. Final contact clearance.
8. Check contact pressure.
A. Using a pressure gage as shown
in Figure 26 check the contact
pressure. Force on the gage rod
must be applied at right angles
to the contact surface. The force
required to separate a stationary
contact from its moving contact
should be 7.5 ± 0.5 lb.
Figure 26. Measuring fixed contact holding force.
NOTE: To help determine when the
applied force causes contact separation, an electrical continuity check
can be used.The faces of all contacts
except the set being measured are
isolated with strips of thin insulating
material.
B. The separating force on a new set
of contacts is generally greater
than 7.5 lb.Therefore, the adjustment of new contacts will be in
the direction of reducing contact
pressure.
C. To reduce contact pressure:
(1 ) Insert a screwdriver between
the stationary and moving
contact tips and pry in the
direction to move the stationary contact away from the
moving contact tip.Adjust the
pressure toward the high
side.
NOTE: A “feel” for applying proper leverage is easily determined
after the first trial. Make smalI
changes in pressure until experience has been gained.
D. To increase contact pressure:
(1 ) With the switch open, bend
each contact finger inward.
Then close switch and repeat
step C.
E. Equalize the pressure on each
side of a set of contacts as closely as possible.
F. After all contact pressure adjust-
ments have been made, check
that the contacts have a gap of
1/4 (+1/32 -1/16) inch. (See Figure 27.)
9. Manually operate the switch a few
times to observe contact alignment
and clearances to verify that all parts
have been properly secured.
S260-20-9
Figure 27. Stationary contact gap.
TYPE VLR SWITCH
If it has been determined that the contacts must be replaced, refer to Figure
28 and proceed as follows:
1. Remove the movable contact yoke
assembly.
A. Remove the stop nut and flat
washer from the end of the contact rod.
B. Remove the yoke positioning
spacers and drive out the roll
pin.
C. Note the flat washer arrange-
ment above and below the movable contact yoke. Be sure to
replace in the same order.
D. Remove and discard the mov-
able contact yoke assembly.
2. Remove the stationary contact as
sembly.
A. Remove the brass hex nuts, lock-
washers and flatwashers attaching the mounting brackets to the
bushing rods.
11
Page 12
Figure 28. Type VLR switch contact assembly.
B. Lift the entire contact housing
assembly from the bushings and
the contact rod, which remains
attached to the operating link.
3. Disassemble the stationary contact
assembly.
A. Remove the contact tube straps
by removing the round head
machine screw and associated
hardware.
B. To free the contact tubes from the
housing, grasp a tube firmly in
each hand and with a slow
steady movement spread the
tubes away from the housing, as
shown in Figure 29, until the
band is released from the tubes.
C. Remove and discard the station-
ary contact tube assemblies.
4. Reassemble the stationary contact
structure with new contact tube
assemblies.
A. Use the reverse order of step 3B
and Figure 29 to reassemble the
tubes and tube band, making
sure the notch in the tube lines
up with the tab in the band.
B. Secure the tubes to the housing
with the tube straps.
5. Reinstall the stationary contact structure into the switch.
A. Install the assembly over the con-
tact rod and attach to the bushing rods with the flat washers,
lockwashers, and brass nuts; do
not tighten.
Figure 29. Dismantling contact tubes.
6. Align the stationary contact assembly.
A. With the switch mechanism in the
open position, the top of the dashpot
piston on the contact rod should be
1/32 inch above the top surface of
the dashpot. (See Figure 19.) Adjust
the nuts on the bushing rod to move
the contact housing up or down as
required.
B. With a “sailboat” alignment fixture
spanning the machined surfaces
of the head casting, check the
axial squareness of the contact
housing as shown in Figure 30.
obtain proper squareness by
adjusting the bushing nuts while
Figure 30.
Checking axial and longitudinal
squareness with “sailboat”alignment fixture.
maintaining the alignment of step
6A.
NOTE: A typical sailboat alignment
fixture is shown in Figure 31. If a fixture is not available the procedure for
aligning VR and VCR contact boxes,
described on page 31, can be used.
C.With the contact housing squared,
tighten both outer bushing nuts
securely without disturbing the
position of the inner nuts.
D. Square the side of the contact
housing with the head casting as
shown in Figure 30. If misalignment exists, adjust by bending
the entire structure as required.
7. Install and align the movable contact
yoke assembly.
A. Replace the correct number of
washers above and below the
contact yoke as noted in Step 1
C during disassembly.
B. Reinstall roll pin, spacers, washer
and stop nut to complete the
reassembly.
C. Unhook the closing spring from
the drive stud and manually
crank the mechanism until the
drive stud reaches the 7 o’clock
position; approximately 42 revolutions.
D. Crank slowly from this point to
bring moving contacts toward the
stationary contacts.
NOTE: If switch is equipped with
quickclose accessory, the mechanism will latch in the 7 o-clock position. To release, push the quick close
solenoid plunger up into the solenoid.
E. As the moving contacts approach
the stationary contacts observe
their alignment. Misalignment
can be corrected by twisting the
12
Page 13
Figure 31.
Typical “sailboat”fixture for aligning contact housing.
rected by twisting the moving
contact yoke about the contact
rod. The link at the end of the
rod will permit enough twist to
obtain the adjustment required.
F. To confirm proper contact
engagement, crank the mechanism to the fully closed position.
Check clearance between the
movable contact yoke and the
top of the contact tubes as
shown in Figure 32.Vary
S260-20-9
the number of washers above
and below the yoke assembly to
obtain the proper clearance.
G. Manually trip open the switch and
reattach the closing spring.
8. ManualIy operate the switch a few
times to observe contact alignment
and clearances to verify that all parts
have been properly secured.
Actuator Mechanism
Normally, little maintenance is required
on the actuator mechanism. However,
periodic checks should be made to
assure trouble-free operation.
ELECTRICAL COMPONENTS
If the switch does not operate electrically but can be manually opened and
closed, check the electrical components.
1. Make a continuity check for broken or
loose wiring.
2. Manually operate the miniature con-
trol switches and check contact
operation.
3. Apply rated operating voltage to the
motor and solenoids to verify their
operation.
Replace any components or wiring
found defective. The connection diagram for the standard operator is shown
in Figure 33; and for the quick-close
operator in Figure 34.
Figure 32.
Type VLR switch contact engagement.
Figure 33.
Connection diagram for standard operator.
13
Page 14
Figure 34. Connection diagram for quick-c lose operator.
TRIP SOLENOlD
If the trip solenoid plunger becomes
rusted, it can be cleaned with crocus
cloth. A severely eroded plunger and/or
frame, or a faulty solenoid necessitates
the replacement of the entire trip
solenoid assembly. Proceed as follows:
1. Remove the speed-nut and washerfrom the upper end of the manual
trip rod to free the trip solenoid
mounting plate.
2. Remove the screws and lockwashers
attaching the mounting plate to the
speed reducer frame, and lift out the
mounting plate as shown in Figure
35.
3. To replace the solenoid assembly,
first remove the retaining ring
attaching the plunger link to the toggle lever, then cut the black solenoid
leads close to the coil and remove
the attaching hardware to free the
solenoid frame from the mounting
plate.
4. Install new solenoid assembly,
reconnect the plunger link to the
toggle trip lever, and secure with a
C-ring. Splice the white and black
leads to the solenoid leads.
5. Attach mounting plate to the speed
reducer frame and reinstall the
washer and speed-nut to the upper
end of the manual trip rod. Be sure
the crook of the pull rod extends
above the plunger pin.
Figure 35. Detaching mounting plate.
14
Page 15
MOTOR REPLACEMENT
The actuator motor used in Type VR,
VCR, and VLR switches with ser ial
numbers below those listed in Table 4 is
no longer available. To adapt the new
motor to these switches a motor
replacement kit, KA725VR, is available.
The kit includes the new motor and all
parts required for the adaptation.
Replacement instructions are included
with the kit.
Switches with serial numbers above
those referenced in Table 4 have the
new design motors installed during
manufacture and do not require the
replacement kit. They may be replaced
directly on a one-to-one basis.
To replace a motor simply disconnect
the motor leads and remove the attaching hardware. Make sure the drive gear
on the motor shaft meshes correctly
with its mating reduction gear when
installing the new motor.
S260-20-9
Table 4
Switches Requiring Motor
Replacemnt Kit.
Below
Type Serial Number
VR 2809
VCR 2344
VLR 1208
SPEED REDUCER
Speed reducer maintenance is limited
to a periodic greasing of gears with an
allweather, non-freezing grease. If
speed reducer must be replaced, refer
to Figure 36 and proceed as follows:
1. With the main switch contacts open,
remove the closing spring from the
crank lever drive pin.
2. Disconnect the two black motor
leads.
3. Remove the pull rod and the mount-
ing plates.See page 45.
4. Remove the C ring, identified in Fig-
ure 37, to free the toggle assembly
pin. Raisethetr ipleverandpulloutthepin, releasing a spacer and
freeing the spring link and toggle
from the shaft lever.
Figure 36.
Actuator parts identification.
Figure 37. Operating shaft lever attachement.
15
Page 16
5. Remove hexhead screws that secure
the speed reducer to the actuator
housing.
6. Lift out the speed reducer with toggle
assembly and opening springs
attached as shown in Figure 38.
Remove the springs from the lower
spring link.
7. Remove the C ring to release the flat
washer, lower spring link, spacer and
toggle assembly from the toggle
shaft. Remove C r ing and closing
spring bushing from the crank lever.
8. Replace spring link and spacer on
toggle shaft of new speed reducerand secure with C ring. Attach
opening springs to spring link.
CAUTION: Stop bolt, for
!
operating shaft lever, is factory
set and should never be readjusted.
9. Install new speed reducer in actuator housing. Moderately tighten hexhead screws. Be sure latch lever is
positioned behind stop-lever roll pin
as shown in Figure 36.
10. Lift trip lever and insert toggle pin to
secure toggle, spacer, and upper
spring link to shaft lever. Secure pin
with C ring. Attach opening springs
to upper spring link. Be sure toggle,
spacer, and link are positioned as in
Figure 37.
11. Attach mounting plate to speed
reducer frame. Slip pull rod through
mounting plate slot and secure with
speed nut and washer.
12. Tighten hexhead screws that secure
speed reducer to actuator housing.
13. Install closing spring bushing and
secure with C ring.
14. Attach closing spring onto crank
lever drive pin. Operate actuator
mechanism manually with crank to
close contacts. Open contacts with
manual trip rod. Repeat operation
of actuator mechanism electrically
and check for proper operation.
Figure 38. Detached speed reducer .
16
Page 17
S260-20-9
SERVICE PARTS LIST
The service parts and hardware listed
and illustrated include only those parts
and assemblies usually furnished for
repair or involved in the maintenance
procedures described in this manual.
Further breakdown of listed assemblies
is not recommended.
Dimensions of all common hardware
parts have been carefully checked so
that they may be locally acquired. The
suffix letter of the 14 character catalog
number for common hardware parts
codes the plating of the part:
A—No plating; raw material
H—Silver
M—Black oxide
Q—Cadmium + zinc + chromate
Y —Zinc + chromate
Z —Electro zinc + bronze irridite
A hardware kit, Catalog No.
KA849R1, contains an assortment of
roll pins, cotter pins, retaining rings,
stop nuts, etc.— common hardware
parts used in Cooper Power Systems
switches that may not be readily locally
available.
To assure correct receipt of any part
order, always include switch type and
serial number. Because of Cooper
Power Systems continuous improvement policy, there may be instances
where the parts furnished may not look
exactly the same as the parts ordered.
However, they will be completely interchangeable without any rework of the
recloser.
All parts carry the same warranty as
any whole item of switchgear, i.e.
against defects in material or workmanship within a period of one year from
date of shipment.
17
Page 18
Figure 39. T ank and head assemb ly parts.
18
Page 19
Tank and Head Assembly Parts
(Figure 39)
S260-20-9
Item Catalog Per
Qty.
No. Description Number Assy.
1 Bushing assembly, complete
(includes items 6, 7, 8 and 9)
Standard creepage KA160E7 6
17-inch creepage KA160E8 6
2 Capscrew, hex hd, 3/8-16 x
1-5/8, stl K730101137162Q 18
3 Bushing clamp KP41L 18
4 Clamping ring KP121L 6
5 Lower bushing gasket KP2020A29 6
6 Terminal KA143L900 1
7 Terminal gasket KP2090A57 1
8 Ceramic bushing
Standard creepage KP130VR 1
17-inch extra creepage KP318VR 1
9 Bushing rod KA160E907 1
10 Vented dipstick KA213VR 1
11 O-ring gasket KP2000A46 1
12 Capscrew, hex hd, 3/8-16
x 3, stl K73101137300Q 10
13 Washer KP2028A23 10
14 Combination nut and pin KP3061A3 10
15 Capscrew, hex hd,1/2-13
x 1-1/4, stl K730101150125Q 2
16 Split lockwasher, med,1/2, stl K900801050000Z 2
17 Lifting lug KP456H1 2
Item Catalog Per
Qty.
No. Description Number Assy.
18 Head casting (includes
operating shaft bushing) KA701VR 1
19 Oil seal KP259VR 1
20 Head gasket KP2103A6 1
21 Shaft and levers assembly KA23VR 1
22 Rubber seal KP2090A44 1
23 Indicator KA19VR 1
24 Roll pin, 3/16 x 1-1/8, stl K970801187112M 1
25 Washer KP164VR 1
26 External retaining ring KP2013A1 1
27 Shaft bearing KP88VR 1
28 Split lockwasher, med, 5/8, stl K900801062000Q 6
29 Capscrew, hex hd, 5/8-18 x 2,
stl K730101162200Q 6
30 Retaining ring, Type C, 1/4
stl (WA514) K970901250000M 6
31 Pin KP3124A18 3
32 Contact operating link KP17VR 3
33 Tank liner kit KA761H3-2 1
34 Tank assembly KA3VCR 1
35 Capscrew, hex hd, 1/2-13 x 1,
stl K730101150100Q 1
36 Parallel ground clamp KA227H 1
37 Pipe plug 1/2, sq hd KP2007A3 1
38 Oil sampling and drain valves KA809R 1
19
Page 20
Figure 40. Type VR contact assembly parts.
Type VR Contact Assembly Parts (Figure 40)
Item Catalog Per
Qty.
No. Description Number Assy.
1 Hex jam nut, light, 5/8-18,
brass K880725318062A 4
2 Washer KP2028A45 4
3 Split lockwasher, med, 5/8,
bronze K900830062000A 2
4 Retaining ring, Type C, 1/4,
stl (WA514) K970901250000M 2
5 Pin KP31 24A18 1
6 Contact rod assembly KA200VR 1
Stationary contact assembly
complete (includes items 7
through 11) KA199VR1 1
20
Item Catalog Per
No. Description Number Assy.
7 Contact housing support
8 Mounting bracket KP134VR1 2
9 Stationary contact assembly KA209VR 2
10 Capscrew, hex hd, 5/16-18 x
11 Split lockwasher, med, 5/8, stl K900801062000A 4
12 Movable contact assembly KA201VR 1
13 Machine screw, rd hd, 10-32
Qty.
assembly KA211 VR1 1
2-1/4, stl K730101131225A 4
x 1, stl K721501310100A 2
Page 21
S260-20-9
Figure 41. Type VCR contact assembly parts.
Type VCR Contact Assembly (Figure 41)
Qty.
Item Catalog Per
No. Description Number Assy.
1 Hex jam nut, light, 5/8-18
brass K88072S318062A 4
2 Washer KP2028A45 4
3 Split lockwasher K9008300620000A 2
4 Retaining ring, Type C, 1/4,
stl (WA514) K970901250000M 2
5 Pin KP3124A18 1
Contact assembly, complete
(includes items 6 through 24) KA704VCR 1
6 Contact rod assembly KA200VR 1
7 Movable contact assembly KA36VCR 1
8 Machine screw, rd hd, 10-32
x 1, stl K721501310100A 2
9 Elastic stop nut, 10-32 KP2020A1 2
Stationary contact assembly
complete (includes items 10
through 24) KA30VCR 1
10 Contact support assembly KA34VCR 1
11 Mounting bracket KP134VR2 2
12 Stationary contact assembly,
load KA32VRC 2
13 Internal tooth lockwasher
5/16 sil brz K901033031000A 4
Item Catalog Per
Qty.
No. Description Number Assy.
14 Double-ended stud KP138VCR 4
15 Plate, right hand KP127VCR1 1
Plate, left hand KP127VCR2 1
16 Stationary contact assembly,
arcing
Right hand KA33VCR1 1
Left hand KA33VCR2 1
17 Plate KP128VCR 2
18 Plain washer, 5/16, SAE, stl K900201031000A 4
19 Internal tooth lockwasher,
5/16, sil brz K901033031000A 4
20 Hex nut, 5/16-18, stl K881001118031A 4
21 Resistor mounting bracket
right hand KP118VCR901 1
Resistor mounting bracket,
left hand KP118VCR902 1
22 Split lockwasher, med, No.8,
stl K900801008000A 4
23 Machine screw rd hd
8-32 x 7/16, stl K721501108043A 4
24 Resistor, 3.2 ohms (Cutler
Hammer G3AL320) K999904250136A 2
21
Page 22
Figure 42. Type VLR contact assembly parts.
22
Page 23
Type VLR Contact Assembly (Figure 42)
S260-20-9
Item Catalog Per
Qty
No. Description Number Assy.
1 Hex jam nut, light, 5/8-18,
brass K880725318062A 4
2 Washer KP2028A4S 4
3 Split lockwasher, med, 5/8
bronze K900830062000A 2
4 Retaining ring, Type C 1/4
stl (WAS14) K970901250000M 2
5 Pin KP3124A18 1
6 Contact rod assembly KA5VLR 1
Stationary contact assembly
complete (includes items 7
through 13) KA4VLR1 1
7 Contact housing support KA3VLR 1
8 Stationary contact housing
assembly KA7VLR 1 2
Item Catalog Per
Qty.
No. Description Number Assy.
9 Machine screw, rd hd, 10-32
x 2-1/2, stl K721501310250A 2
10 Split lockwasher, med
No.10, stl K900801010000Z 2
11 Hex nut, 10-32, stl K881001332010A 2
12 Tube strap KP111 VLR 2
13 Contact tube band KA98VR 1
14 Movable contact yoke
assembly KA16VLR 1
15 Spacer KP1505R 1
16 Plain washer, 5/8 SAE,
steel K900201031000A 4
17 Stop nut KP2020A4 1
18 Roll pin, 1/8 x 13/16 K970801125081M 1
23
Page 24
Figure 43. Actuator mechanism parts.
24
Page 25
Actuator Mechanism Parts (Figure 43)
S260-20-9
Item Catalog Per
Qty.
No. Description Number Assy.
1 Cover KP129VR 1
2 Cover gasket KP2084A1 1
3 Plate, MANUAL TRIP KP245VR 1
4 Plate, OPEN KP730R 1
5 Self-tap screw, rd hd, Type Z,
No.2 x 3/16, sst K801515002018A 4
6 Manual trip assembly KA65VR900 1
7 Spring KP157VR 1
8 Spacer KP3007A8 1
9 Plain washer, 1/4 AN, stl K900201026050Z 1
10 Plain washer, No.10S, brass K900525020043A 1
11 Speed nut KP2005A1 1
12 Mounting plate KP87VR 1
13 Machine screw, rd hd, 10-32
x 3/4, sst K721515310075A 2
14 Split lockwasher, med, No.10,
stl K900801010000Z 2
15 Trip solenoid assembly
120 vac KA185VR1 1
125 vdc KA185VR2 1
48 vdc KA185VR3 1
24 vdc KA185VR4 1
16 Machine screw, 10-32 x 1/2, stl K72150130050Z 4
17 Elastic stop nut, 10-32 KP2020A1 4
18 Nylon wire clip KP2006A1 1
19 Pin KP314VR 1
20 Link KP83VR 1
21 Spacer KP3004A24 1
22 Plain washer, No.6 SAE, stl K900201006000Z 1
23 Retaining ring, Type C, 1/4,
stl (WA514) K970901250000M 1
24 Support and lever assembly KA41VR 1
25 Machine screw, 10-32 x 1/2, stl K721501310050Z 2
26 Elastic stop nut, 10-32 KP2020A1 2
27 Closing spring KP533GW 1
28 Retaining ring, Type C, 3/8,
stl (WA518) K970901375000M 1
29 Sleeve KP280VR 1
30 Retaining ring, Type C, 5/16,
stl (WA516) K970901312000M 1
31 Plain washer, No.20S, brass K900525312000A 1
32 Spring link KP31VR 2
33 Spacer KP3011A6 1
34 Plain washer, 1/2, brass K900525056125A 1
35 Toggle assembly KA11 VR1 1
36 Retaining ring Type C, 5/16,
stl K970901312000A 2
37 Spacer KP3010A7 1
38 Pin KP3125A7 1
39 Opening spring KP35VR 2
40 Speed reducer (includes items
42 through 45) KA32VR 1
41 Capscrew, hex hd, 5/16-18
x 3/4, stl K731001131075Q 4
42 Split lockwasher, med, 5/16, stl K900801031000Z 4
43 Motor assembly KA225VR 1
44 Spacer KP3009A159 3
45 Split lockwasher, med, 14, stl K900801025000Z 3
46 Machine screw, rd hd, 1/4-28
x 1 -18, stl K721501325112Q 3
47 Receptacle assembly KA129VR 1
48 Self tap screw, rd hd, Type Z,
No.6 x 3/8, stl K801515006037A 4
Item Catalog Per
Qty.
No. Descrliption Number Assy.
49 Plug assembly KA98NR 1
50 Terminal strip KP2101A7 1
51 Marker KP40VR 1
52 Machine screw, rd hd, 8-32
x 3/4, stl K721501108075Z 2
53 Split lockwasher, med, No.8,
stl K900801008000Z 2
54 Hex nut, 8-32, stl K881001132008Z 2
55 Switch mounting panel KP344VR 1
56 Machine screw, rd hd, 100-32
x 3/4, stl K721501310075Z 3
57 Split lockwasher, med, No.10,
stl K900801010000Z 3
58 Plain washer, No. 10, stl K900201010000Z 3
59 Spacer KP3007A37 3
60 Switch and latch assembly KA182VR900 2
61 Machine screw, rd hd, 8-32
x 1/2, stl K721501108050Z 4
62 Elastic stop nut, 8-32 KP2020A5 4
63 Spacer KP3007A35 2
64 Crank assembly KP141VR 1
65 Self-tap screw, pan hd,.10-32
x 1/8, sst KP751717110037A 1
66 Mounting clip KP1091ME 1
67 Latch-in spring KP72VR 1
68 Machine screw, rd hd, 10-32
x 7/8, stl K721501310087Z 2
69 Split lockwasher, med, No.10
stl K900201010000Z 2
70 Hex nut, 10-32, stl K881001332010Z 2
71 Machine screw, rd hd, 5/16-18
x 1-1/4, brass K721525131125A 1
72 Flat washer, 5/16 AN, stl K900201032056Z 2
73 Hex nut, 5/16-28, stl K880201118031Q 1
74 Latch KP268VR 1
75 Wing nut K881201118031Z 1
76 Counter assembly KA28C03 1
77 Self-tap screw, rd hd, No.6
x 3/8, sst K801515006037A 2
78 Capscrew, hex hd, 3/8-16
x 1-1/2, stl K730101137150Q 1
79 Hex nut, 3/8-16, stl K880201116037Q 1
80 Split lockwaser, med, 3/8, stl K900801037000Z 1
81 Plate, CLOSED KP729R 1
82 Nameplate KP131 VR 1
83 Control rating plate KP289VR1 6
84 Self-tap screw, rd hd, Type Z,
No.2 x 3/16, stl K801515002018A 6
85 Cover KP158VR 1
86 Gasket KP649VR 1
87 Machine screw, rd hd, 10-32
x 3/4, sst K721515310075A 4
88 Split lockwasher, med, No.10,
stl K900801010000Z 4
89 Hex nut, 10-32, stl K880201332010Z 4
90 Gasket KP78VR 1
91 Gasket KP77VR 1
92 Mechanism housing KA230VR1 1
93 Capscrew, hex hd, 3/8-16 x 1,
stl K730101137100Q 4
94 Split lockwasher, med, 3/8, stl K900801037000Z 4
25
Page 26
Figure 44. Quick-close mechanism parts.
Type VR Contact Assembly Parts (Figure 40)
Item Catalog Per
Qty.
No. Description Number Assy.
1 Bracket KP188VR 1
2 Machine screw, rd hd, 10-32
x 3/4, stl K721501310075Z 2
3 Split lockwasher, med, No. 10,
stl K900801010000Z 2
4 Plain washer, No.10 SAE,
brass K900225010000Z 2
5 Solenoid assembly, 120 vac KA185VR1 1
6 Machine screw.rd hd, 10-32
x 5/16, stl K721501310031Z 2
7 Split lockwasher, med, No. 10,
stl K900801010000Z 2
8 Machine screw, rd hd, 8-32 x 1,
stl K721501108100Z 1
9 Hex nut, 8-32, stl K881001132008Z 2
10 Plain washer, No. 8S, brass K900525014031A 1
11 Latch assembly KA72VR 1
12 Pin KP185VR 1
Item Catalog Per
Qty.
No. Description Number Assy.
13 Bracket KP186VR 1
14 Cam KP312VR 1
15 Machine screw, rd hd, 1/4-20
x 1 /2, stl K721501125050Z 1
16 Split lockwasher, med, 1/4 K900801025000Z 1
17 Miniature switch KP2181A13 1
18 Insulation KNC1070A1 1
19 Machine screw, rd hd, 6-32
x 1, stl K721501106100Z 2
20 Elastic stop nut, 6-32 KP2020A6 2
21 Latch assembly KA204VR900 1
22 Spacer KP3032A11 1
23 Machine screw, 6-32 x 1, brass K721525106100A1 1
24 Plain washer, No. 6S, brass K900525017037A 1
25 Split lockwasher, med, No. 6,
sil brz K900830006000A 1
26 Hex nut, 6-32 brass K881025132006A 1
26
Page 27
Page 28
©1989 Cooper Industries, Inc.
P.O. Box 2850, Pittsburgh, PA 15230
11/83
KBP
Loading...