Cooper P4R User Manual

Vault

These installation instructions are valid with the above Ametrix styles.

C-Scroll

Roundel

Installation Instructions

Sheet 1 of 2

Small, OUTDOOR

P4R

(P

endant

, 4

-way

, R

emote ballast

Visor and Non-Visor

Warning

that all sources of power are turned off. All
work must meet local/national codes and be
performed by a certified electrician.
mount fixtures vertically.

: Before starting any work ensure

Do not

)

Exploded view and part call-out

Cover plate

1/4-20 x4 1/2"
Hex cap bolt
(4x)

5/16-18 x1/2"
Nut
(4x)

Quad fixture assemblies require additional bracing/structure

around J-box to support fixture.

2

Attention:

Wiring the fixture

#8-32 x 3/8"
Set screw (2x)

Canopy

Wire seal

1

1/4" fasteners
(by others)
(4x)

#8-32 x3/8"
Set screw
(2x)

Cover plate

1.

Remove all 1/4-20 x4 1/2" hex bolts from bottom of pendant.

2.

Remove both #8-32 x 3/8" set screws and allow canopy to

slide down pendant.

3.

Run wires from J-box into pendant, ensure there is enough

wire to reach cover plate.

4.

Using appropriate fasteners, secure fixture to ceiling.

additional bracing around J-box to support fixture.
5

. Replace canopy and secure using both set screws.

3

Mounting Pendant to J-box

J-box
(by others)

Use additional bracing
around J-box to support
fixture.

Canopy

1/4-20 x4 1/2"
Hex cap bolts
(4x)

Use

Sealing the outdoor fixture

Cover plate

Wiring hole

1/4-20 x4 1/2"
Hex bolts
(4x)

1.

With pendant secure, slide fixture assembly onto pendant

and secure with four 1/4-20 x4 1/2" hex bolts.

2.

Remove cover plate and insert wires from fixture heads into

wires seals and pull through opening in pendant.

3.

Attach appropriate wires and ensure all connections are

properly matched.

4.

Push connections into pendant and secure cover plate.

Wiring seals
(4x)

#6-32 x1/2"
Socket cap screw
(8x)

#6-32 x5/8"
Socket cap screw
(4x) Compression fitting

1.

Ensure all door screws are secure on fixture head. Refer to
supplementary sheets for torque specs and aiming
instructions.

2.

Ensure gaskets on cover plates are smooth and compressed.

3.

Ensure wires entering compression fittings are sealed and
secure.

Cover plate
gasket (x2)

(x4)

ADY071469 REV B (ECN80481)

Vault w/ visor

LAMP

These installation instructions are valid with the above Ametrix styles

1

"

2

12.70

C-Scroll w/ visor

Mounting Plate Dimensions In [mm]

Length dependant

on order

6"

152.40

Roundel w/ visor

1

4

"

2

114.30

Installation Instructions

Small, OUTDOOR

P4R

(P

endant, 4-way, Remote ballast

Visor and Non-Visor

Warning

that all sources of power are turned off. All
work must meet local/national codes and be
performed by a certified electrician.
mount fixtures vertically.

2"

50.80

: Before starting any work ensure

Sheet 2 of 2

Do not

3

"

4

19.05

3
4

19.05

13
32

10.16
(4x)

)

"

"

Side view Top view

Lamping Size Chart

(lamps provided by others)

FIXTURE SIZE

(inches/ mm)

10

/ 273.05 39 W 1 T6 Ceramic Metal Halide

3/4

12

/ 323.85 70 W 1 T6 Ceramic Metal Halide

3/4

12

/ 323.85 150 W 1 T6 Ceramic Metal Halide

3/4

12

/ 323.85 26 W 1

3/4

12

/ 323.85 32 W 1

3/4

12

/ 323.85 42 W 1

3/4

WATTAGE

# OF

LAMPS

LAMP TYPE LAMP DESCRIPTION

4-Pin Triple

Tube

4-Pin Triple

Tube

4-Pin Triple

Tube

Compact Fluorescent

Compact Fluorescent

Compact Fluorescent

6"

152.40

1

4

"

2

114.30

(not to scale)

Use only GE or Sylvania

CFL lamps

10

/ 273.05 100 W 1 T4 Halogen (Single Ended)

3/4

12

/ 323.85 150 W 1 T4 Halogen (Single Ended)

3/4

12

/ 323.85 250 W 1 T4 Halogen (Single Ended)

3/4

ADY071469 REV B (ECN80481)