COOLSHIRT?SYSTEMS Pro Air & Water System Manual
Pro Air & Water System
Made in the U.S.A
Congratulations on your purchase of the world’s finest Driver Cooling System
The COOLSHIRT® Pro Air & Water System is the finest Driver Cooling System Available today. Used
by drivers in all levels of racing, this system delivers the ultimate in driver cooling comfort. The Pro
Air & Water System delivers temperature controlled cooled water to the driver’s COOLSHIRT® while
providing cooled HEPA-4 filtered, blower enhanced air to the driver’s helmet.
COOLSHIRT Personal Cooling Systems are manufactured in the USA and contain the highest quality
components available. With proper installation and maintenance, your system will provide you with
years of dependable service. Please inspect your purchase to ensure that your system contains the
selected components listed below. If there are any discrepancies, please contact COOLSHIRT
SYSTEMS Customer Service at 800-345-3176 immediately.
Included with your system:
Quantity
_________ 1
_________ 1
_________ 1
_________ 1
_________ 1
_________ 2
_________ 1
_________ 1
_________ 1
_________ 1
_________ 1
_________ 1
_________ 2
Part #
PSAW-12/24
H-12-S
FC-2
MT-12/24
AIRH-8
HEF-1½
HEF-H
A-x3X3FT
HEF-4
FS-10
FS-1
BF-235
IC
Description
Platinum Series Cooling Unit w/ heat exchanger & internal pump
12-foot insulated water hose with quick disconnects
Dual Flow Temperature Control Switch for Air & Water
Mounting Tray with tie-down strap
8-foot x 1½” diameter heavy-duty clear Helmet Air Hose
Blue Air Hose Connectors: 1/½” diameter
Blue helmet connector for Air Hose
3’ x 3” heavy duty clear intake air hose
4” blue intake air Hose-to-Blower connector
HEPA-4 Micron Air Filters: 10 per package
Metal Screen for Air Filter
235CFM Blower with 1½” Blue Filter Housing attached
Block Ice Container
System Specifications:
Dimensions
PSAW-12: 14”L x 9.5”W x 11”H
PSAW-24: 15.5”L x 10.5”W x 13”H
© 2014 COOLSHIRT SYSTEMS, 170 Andrew Drive, Stockbridge GA 30281
Office : 800-345-3176 Fax: 678-289-4325 www.coolshirt.com
__________________________________________________________________
Cooling Time
3 Hours
6 Hours
Dry Weight
6 lbs.
7 lbs
Power Required
235 CFM Blower: 2.9A, 12V Water Pump: 2.0A, 12V
235 CFM Blower: 2.9A, 12V Water Pump: 2.0A, 12V
Pro Air & Water System
Installation Instructions:
MOUNTING TRAY (MT-12/24) and COOLING UNIT (PSAW-12/24)
1) Select mounting tray location and permanently attach the tray to the racecar with any
appropriate hardware (not provided). Place cooling unit into the mounting tray.
2) Thread the tie down strap through one of the two slots provided on the cooling unit, then
run the strap down through the slot on the same side of the mounting tray. Run the strap
lengthwise under the cooling unit between the mounting tray and cooling unit, through the
slot on the other side of the mounting tray and up through the slot in the top of the
cooling unit.
3) Use the clamp provided on the strap to secure the cooling unit to the tray. The cooling unit
and mounting tray were packaged this way from the factory prior to shipping to
illustrate proper placement of the tie-down strap.
Note: Ensure that the 12-foot water hose
driver. Do not allow the hose to come into contact with any hot metals as this may
damage the hose.
BLOWER (BF-235)
1) Select the cockpit location for the blower and permanently mount the blower to the
racecar using any appropriate hardware (not provided)
2) Make sure that the 3-inch air intake is pointed towards the outside of the car. Place filter
and screen and fasten with a tie-wrap or clamp (not provided).
CAUTION: DO NOT OVER TIGHTEN AS THIS CAN CAUSE DAMAGE TO THE FAN BLADES
and the 8-foot x 1½” air hose can reach the
TEMPERATURE CONTROL SWITCH
1) Select the location for the Temperature Control Switch and permanently mount the switch
to the racecar using any appropriate hardware (not provided). The switch has a faceplate
that allows for convenient in-dash mounting or it may be mounted at any location that is
accessible by the driver
2) Wire the cooling unit and the blower to the Temperature Control Switch using appropriate
lengths of wire (not provided). As the instructions provided with the switch illustrate:
Cooling Unit: brown = + (positive), black= - (negative)
Blower: yellow= + (positive), black= - (negative)
Now wire the Temperature Control Switch to the racecar’s 12V system and ground
properly using the instructions provided with the switch.
© 2014 COOLSHIRT SYSTEMS, 170 Andrew Drive, Stockbridge GA 30281
Office : 800-345-3176 Fax: 678-289-4325 www.coolshirt.com
Loading...