Cooler Master Glacer 240L User Manual

CPU Cooler and motherboard setup for use with: AMD® AM2/(+), AM3/(+), FM1, FM2, 939

1. Remove the OEM AMD Plastic bracket from the top of the motherboard

4. Apply Thermal Paste to top of CPU in a thin even layer.

2. Please remove the factory installed Intel mounting brackets from the CPU Cooler.

5. Remove the protective film on bottom of CPU Cooler.

3. Install the supplied AMD brackets to the CPU Cooler as shown below.

Radiator Mounting

With the CPU cooler hanging freely, and holding the radiator as shown, fasten it to the case using the provided screws.

Pump Mounting

Orientation of the radiator may vary depending on your case. A typical (most common) example is shown here.

Alternate tightening the 4 screws to the motherboard and back plate to provide even pressure to the CPU.

User Guide

Congratulations on your purchase of Cooler Master Liquid Cooling System (LCS). Your LCS has been factory prefilled, leak-tested, and once configured for your particular CPU socket,is designed for plug-and-play installation, as well as very low maintenance operations.

Prior to installing your LCS, we strongly suggest that you read this installation guide thoroughly, then make sure that all components are included in the package, and finally that you follow the installation sequence step-by-step. Improper installation may cause permanent damage to your system as well as to the LCS.

When in doubt, always contact our technical help first: http://www.coolermaster-usa.com/glacer

Specifications

Intel® LGA 1366/1150/1156/1155/775 Back-Plate Installation

Radiator

Material Brass Tubes, Copper Fins Body Dimensions 269mm x 127mm x 29mm / 10 19/32” x 5” x 1 9/64” Fill-Port thread G1/4

Fan

Dimensions 120mm x 120mm x 25mm Speed 2400 RPM Airflow 86.15 CFM

Static Pressure 0 → 2.65 mH20 Noise Level 16 → 40.33

Connector 4-Pin PWM

Pump

Speed PWM adjustable 1200 ~ 3500 RPM Voltage 12v Connector 4-Pin PWM, SATA power connector

Tubing

Material PVC Dimensions 5/8” x 3/8” (16/10mm)

CPU Socket Compatibility

Intel® LGA 1366, 1150, 1155, 1156, 775, 2011 AMD® AM2/(+), AM3/(+), FM1, FM2, 939

1. Remove the back bracket from the waterblock by loosening all 4 screws. Do not misplace as it is needed later.

4. Place the back plate on the bottom of motherboard making sure to align the standoffs with the motherboard holes. The CPU cooler can now be mounted to the motherboard.

2. Move each of the adjustable standoffs in position:

LGA 1366: 100% g out LGA 775: 100% f in LGA 1150/55/56: ~20% g out

5. Apply Thermal Paste to top of CPU in a thin even layer.

3. Remove the 4 adhesive foam pads.

6. Remove the protective film on bottom of CPU cooler.

Packing List

Intel® Back Plate x 1 LGA 2011 Spring Loaded Screws x 4

AMD® Bracket with screws x 2

Thermal Paste x 1 Radiator Mounting Screws x 8

Glacer 240L LCS (radiator, 120 mm fan x 2, tubing, waterblock with pump)

SOCKET 2011 Install:

Please remove the nylon retaining washer from each spring-loaded screw by snapping out of its groove, and set aside for future installations/upgrades.

Proceed to Radiator and Pump Mounting on back →

Install the provided Intel® LGA 2011 spring-loaded screws. Secure each spring-loaded screw to the bracket by snapping a nylon retaining washer into the groove of each screw body.

See online for refilling instructions

and additional information.