Coolerator Ar1800xt0 Installation Guide
IMPORTANT:
Read and save
the& instructions.
Part No, 1155965 Rev. E
IMPORTANT
Installer: Leave Installation Instructions
with the homeowner.
Homeowner: Keep Installation Instructions
for future reference.
Save Installation Instructions for local
electrical inspector’s use.
Air Conditioner
Before you start...
Proper installation is your responsibility.
Make sure you have everything
necessary for correct installation.
It is the customer’s responsibility
to comply with the Installation
specifications provided.
Grounded electrical outlet
within reach of the power
supply cord is required. See
Electrical requirements.
Electrical Shock Hazard
It is the customer’s
responsibility:
l To contact a qualified
electrical installer.
l To assure that electrical
installation is adequate
and in conformance with
National Electrical Code,
ANSI/NFPA 704atest
edition and local codes
and ordinances.
Check location where air
conditioner will be installed.
The location should provide:
l A window large enough,
l Adequate wall support for
weight of air conditioner,
l An electrical outlet within
reach of sewice cord,
0 Free movement of air to
rooms to be cooled.
Electrlcal outlet must be
avallable wlthln reach ot
service cord.
Do not use extenslon cord.
Important: Observe all
governing codes and
ordinances.
1
Personal Injury/Product
Damage Hazard
l Because of the weight
and size of the air
conditioner, more than
one person is needed to
move, lift and safely
install it.
l Handle air conditioner
with care. Metal fins on
front and rear coils are
sharp.
. Do Not use the water that
collects inside the air
conditioner for drinking
purposes. It is not
sanitary.
l Maintain a firm hold on
the air conditioner to
prevent it from falling out
the window during
installation.
l Do Not locate air
conditioner where
cabinet front is exposed
to a heat source that
raises the surface
temperature above
120°F.
Failure to follow these
instructions could result in
\
personal injury or damage
to air conditioner.
Tools and
materials
needed for
installation:
-i
‘-2: . .
c
flat-blade .--a
screwdriver
Through-the-wall
installations:
wood
preservative
F . /-*
y.&
10, #10x1’
screws
or smaller bit
Parts supplied
for installation:
‘zrlndow lock 2.slde-
brockeh mbuntlna
window foci strip
gasket
round-head, hex-head.round-head,’ i&ierS
metal metal
.S_CES
-A \
screws
Installation parts are supplied for
double-hung windows up to 40
inches wide. Installation up to 54
inches can be made with a special,
wide window kit available from your
dealer or service center.
top-mountingA
or-$-
wood
screws
Specific electrical requirements are
Electrical
listed in the chart. Follow the
requirements for the type of plug on
requirements
the power supply cord.
Wiring
.
requirements
E!xtrical Shock Hazard
l Electrical ground is required on
this appliance.
l Improper connection of the
Plug Type P
equipment-grounding conductor
line can result in electrical
shock.
l Check with a qualified
J-prong
grounding
DIUO
electrician if you are in doubt as
to whether the appliance is
properly grounded. Do Not
modify the plug on the power
supply cord. If it will not fit the
outlet, have a proper outlet
installed by a qualified
grounding.
type wall
receptacle
electrician.
l Do Not use an extension cord
with this appliance. Such use
may result in a fire, electrical
pvwer
SUPPlY
CO!d
shock or other personal injury.
m Do Not have a fuse in the neutral
or grounding circuit. A fuse in the
neutral or grounding circuit
115volt- 230/208 volt - 2
103.5~ min.,
126.5~ max. 253~ max. 2
could result in electrical shock.
l Grounding wire must be
connected to grounding screw
located in lower left corner of air
conditioner when air conditioner
is in cabinet.
Failure to follow these instructions
:ould result in electrical shock.
A three-wire, single-phase, 60-Hz, AC
only, electrical supply is required on
a separate circuit. A 20-amp timedelay fuse or circuit breaker is
reql .ired. Copper wire (#14-gauge)
7Samp 12-amp rating 1
,atings or less
- double ,ingle outlet
Iutlet is
acceptable. a-te circuit.
‘.6 through
2-amp
atings - use
)nly a single
)utlet and
eparate
:ircuit,
is required.
The model and serial label is located
behind the front panel above the
coil area.
Exomended grounding
Do Not, under any circumstances,
remove the power supply cord
grounding prong.
‘C
For your personal safety, this
appliance must be grounded. This
appliance is equipped with a power
supply cord having a 3-prong
grounding plug. To minimize possible
shock hazard, the cord must be
Plug Type B Plug Type C
receptacle
receptacle
small
tandem 17
blades
grounding
prong
grounding
prong
#30/208 volt -
197.6~ min.,
Ir less - use a
2nd a sepa-
1 97.6~ min.
53~ max.
& rating
C
lr less - use a
si
ngle outlet
C
Ind a sepa-
r(
tie circuit.
Panel A
Loading...